NANOLUX LED SN720 Pro Operating Manual

ALWAYS COMPLY WITH LOCAL
INSTALLATION REGULATIONS AND CODES
The fixture is suitable for indoor environment. Do not install your fixture in wet or
outdoor environment. Do not operate the fixture close to combustible materials. The
fixture will get hot during operation. Do not touch the fixture during or right after
operation. Make sure the power cord does not touch any hot part of the fixture. Make
sure the light bars are clean and inserted correctly. The normal operating environment
temperature should be below 104°F. Exceeding the maximum environmental
temperature will stress electronic components, which will lead to shorter lifetime and
decreased reliability.
DIMMING FUNCTION
This model is compatible with NCCS-RTU/0-10V. When using the function, please
press the to show 0.
DIM mode selection button
Insert telephone wire into the jack of the fixture and 0-10V Lighting Controller, and
then Dimming function on the LED fixture is enabled.
● Maximum of 120 units can be controlled by 0-10V Lighting Controller.
● Simulate sunrise and sunset for dimming.
● Turn off the device automatically following the setting time and temperature.
In & Out jacks included on the fixture allows for multi-fixtures connected in parallel.
CAUTION:
After installation, verify installation was a success by cycling the lights on/off a few
times, by setting 'over temperature shut down' to a low value like 85°F, and rubbing the
temperature probe with your fingers, tricking the 0-10V Lighting controller/NCCS RTU
into an over temperature condition and shutting the lights off. Then leave the probe
alone, and after recommended 10-15 minutes the 0-10V Lighting controller/ NCCS
RTU should turn all the lights back on.
For detailed instructions, please refer to 0-10V Lighting Controller operating manual.
RTU is removed from the fixture during operation, the fixture will automatically turn off
after 10 seconds. If the RTU loses communication with the DTU for any reason, the
fixture will automatically turn off after 10 minutes. If the fixture continues to turn off for
any reason during operation with the RTU in NCCS mode, replace the RTU and
confirm it is communicating with the DTU.
For further NCCS RTU customer support and tech support pages, visit www.
nanoluxtech.com.
When using 0-10V Lighting controller, please insert 0-10V module control wire into the
RJ11 jack of a Nanolux fixture. If 0-10V Lighting controller loses communication with
fixture due to some type of errors, especially resulting from short circuit, fixture will
shut off automatically in 5 seconds. Fixture will turn back on if errors are fixed.
Max 60 Units
LED LED LED
Max 60 Units
LED LED LED
TROUBLE SHOOTING
Problem Probable cause(s)
One or more
Make sure power is on and
fixtures are
Disconnect from power source.
cables are plugged in.
completely off.
Broken cable or wire connecting
Dimming Repair or replace any
controller to fixture or wire
damaged cables if necessary.
failure
connecting fixture to fixture.
The power supply settings do Disconnect fixture from the
LED will not
not match with local AC power supply. Check settings
come on.
voltage and frequency. and correct if necessary.
-04-
SCOPE OF USE AND MAINTENANCE
● Comply with local installation regulations.
● Store the fixture in a dry and clean environment, with an ambient temperature of
-10°C ~ 50°C and ambient humidity of less than 90% RH. It is recommended that
the fixture shall not stay unused for more than six months. If it has stayed unused for
more than six months, please test to ensure fixture is functioning at 100%.
● Please keep products safe. Avoid mechanical pressure, excessive vibration and
dropping the unit during the process of assembly to protect the light bar and track.
● Keep away from water, oil and organic solvent, or it will reduce the efficacy and have
the potential risk of electric leakage.
● All equipment, devices and machines shall be effectively grounded.
● Regularly check and clean the dust from LED array.
1. Disconnect from power supply before general care.
2. Remove the dust from the light bar by using low-pressure compressed air.
3. Clean the diode array with a soft cloth to prevent it from being scratched.
4. Be sure not to touch the diode with your bare hands, even after the LED is
disconnected from power supply.
● It is recommended that you contact a licensed electrician or an expert if any of the
following happens:
1. The cable or the plug has been damaged.
2. The unit has been exposed to rain.
3. Significant changes in the unit performance.
4. Fixture or light bar dropped and corner of its enclosure got bent.
● There are no serviceable parts inside the LED. Opening the LED will void its
warranty.
WARRANTY
Nanolux warrants manufacturing defects of this product if it is used under normal
operating conditions for a period of five (5) years from the original date of purchase. If
the product shows manufacturing defects within this period and that defect is not
caused by user error or improper use, Nanolux shall, at its discretion, either replace or
repair the product by using applicable new or refurbished parts. For any service,
return the product to your shop along with the original sales receipt.
PRODUCT PACKING LIST
No.
A
B
C
D
Possible fixes or
corrective maintenance
PATENTED PRODUCTS, COUNTERFEITING NOT ALLOWED.
A
B
Name Quantity
Folding Fixture 1
YO-Ratchet 4
Telephone Wire 1
Operating Manual 1
Designed by NANOLUX in California
Made in China
OPERATING
MANUAL
LED SN630&720
&830&1000 Pro
NCCS-RTU/0-10V COMPATIBLE
Manual
LED SN630 Pro (6 light bars)
C D
LED SN720 Pro (8 light bars)
LED SN830 Pro (8 light bars)
LED SN1000 Pro (10 light bars)