Page 1
ORDER NO. ITD0310055C2 LCD TV TX-22LT3 LH12 Chassis SPECIFICATIONS Power Source AC 100~240V, 50/60Hz Power Consumption Average use: 67W Stand-by condition: 1.8W TV set DC 15V, 3.8 A max. 22-inch (558 mm), 16:9 aspect ratio LCD panel Screen Size 486.8mm(W) x 273.6mm(H)
Page 2
Playback of NTSC tape from some PAL video recorders (VCR) M.NTSC Playback from M.NTSC Videorecorders (VCR) NTSC (AV input only) Playback from NTSC Videorecorders (VCR) Aerial-Rear Operating Conditions Temperature: 41°F-95°F(5-35°C) Humidity: 5%-90% RH (non-condensing) Connection Terminals AV1 (Scart connecter) 21 Pin socket (Audio/Video in, Audio/Video out, RGB in, Q-Link) AV2 (Scart connecter) 21 Pin socket (Audio/Video in, Audio/Video out, S-Video...
Page 3
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Page 4
2. Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistorsand semiconductor "chip" components.
Page 5
electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparableconductive material).
Page 6
If the CCU ports have been checked and found to be incorrect or not located then “--” will appear in place of “O.K.”. Display Ref. No. Description P.C.B. IC1004 EEPROM DG-Board GC2M IC9001 Global Core DG-Board IC9007 RGB A/D Converter DG-Board IC4001 AVSW...
Page 7
Board Name Function A-Board Main (DC Power Supply, Audio, Input Select, AV Connector) B - Board Tuner DG - Board Global Core, RGB Processor, Micro Processor, Pixel Converter) K - Board Switch PD - Board Back Light Inverter PH - Board Back Light Inverter V - Board RM, LED...
Page 8
4. Remove the fixing screw (1pcs). 5. Remove the hinge cover. 6. Remove the fixing screws (4pcs). 7. Remove the tilt base. 5.2. Removing the rear cover 1. Remove the tilt base. (See 5.1.) 2. Remove the fixing screws (9pcs).
Page 9
3. Remove the rear cover. 5.3. Removing the shield plate 1. Remove the rear cover. (See 5.2.) 2. Remove the fixing screws (8psc). 3. Remove the shield plate. 5.4. Removing the PH shield plate and the PD shield plate 1. Remove the shield plate. (See 5.3.) 2.
Page 10
5.5. Removing the speaker box 1. Remove the shield plate (See 5.3.) 2. Remove the fixing screws A (2pcs) and B (2pcs). 3. Remove the angle. 4. Disconnect the coupler(A9), and unlock the cable clamper and hook to free the cable 5.
Page 11
5.7. Removing the switch unit 1. Remove the shield plate. (See 5.3.) 2. Disconnect the coupler (K1). 3. Remove the fixing screws (2pcs). 4. Remove the switch unit. 5.8. Removing the K-Board 1. Remove the switch unit. (See 5.7.) 2. Remove the fixing screws (2psc). 3.
Page 12
2. Remove the V-Board. (See 5.6.) 3. Disconnect the couplers (PH1, PH2, PD1, PD2 and DG6900), and unlock the cable clampers to free the cable. 4. Remove the chassis. - Disconnecting flexible cable from the coupler. / Lift up both ends of the cable lock (brown colored) simultaneously to release the locking.
Page 13
5.10. Removing the tuner cover and the terminal cover 1. Remove the rear cover. (See 5.2.) 2. Remove the tuner cover. *The tuner cover lever is pulled up and remove the tuner cover. 3. Remove the fixing screws (4pcs). 4. Remove the terminal cover. *A hooks is removed.
Page 14
5.12. Removing the A-Board 1. Remove the shield plate. (See 5.3.) 2. Remove the angle. (See 5.5.) 3. Remove the terminal cover. (See 5.10.) 4. Remove B-Board. (See 5.11.) 5. Disconnect the couplers (A1,A2, A3 and A5). 6. Disconnect the coupler (A9), and unlock the cable clamper to free the cable.
Page 15
5.14. Removing the DG-Board 1. Remove the shield plate. (See 5.3.) 2. Disconnect the couplers (DG1, DG2, DG3 and DG6900). *When removing coupler (DG6900), cautions are required for the handling of a connector. (See 5.9.) 3. Remove the fixing screws (4pcs). 4.
Page 16
5.16. Removing the PD-Board 1. Remove the rear cover. (See 5.2.) 2. Remove the PD shield plate. (See 5.4.) 3. Disconnect the couplers (PD1, PD2, PD3 and PD5). 4. Remove the fixing screw (1pcs). 5. Remove the PD-Board. 5.17. Removing the LCD panel 1.
Page 17
6. Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Mode. 6.1. How to enter SERVICE 1 1. In sound menu, set BASS to MAXIMUM, and set TREBLE to MINIMUM.
Page 30
Ref. No. Part No. Part Name & Description Pcs Remarks C823 ECJ2XB1H104K C 0.1UF, K, 50V C824 ECJ2VF1H103Z C 0.01UF, Z, 50V C826,27 ECJ2VF1H103Z C 0.01UF, Z, 50V C828 F2A1E471A102 E 470UF, 25V C829 F2A1E471A096 E 470UF, 25V C830 F2A1C6810005 E 680UF, 16V C832 F2A0J122A139...
Page 31
Ref. No. Part No. Part Name & Description Pcs Remarks C1031 ECJ1XC1H151J C 150PF, J, 50V C1033 ECJ1XF1C104Z C 0.1UF, Z, 16V C1034 ECJ1XC1H220J C 22PF, J, 50V C1035 ECJ1XB1H102K C 1000UF, Z, 50V C1036 ECJ1XF1C104Z C 0.1UF, Z, 16V C1037 ECJ1VB1H221K C 220UF, K, 50V...
Page 32
Ref. No. Part No. Part Name & Description Pcs Remarks C2202 ECJ2XB1H682K C 6800PF, K, 50V C2203 ECA1HEN2R2 E 2.2UF, 50V C2204 F2A1H2R2A120 E 2.2UF, 50V C2206 ECA1VM221 E 220UF, 35V C2207 F2A1E471A105 E 470UF, 25V C2208 ECJ2YF1C225Z C 22PF, Z, 16V C2209 ECJ2VF1H104Z C 0.1UF, Z, 50V...
Page 33
Ref. No. Part No. Part Name & Description Pcs Remarks C4039 EEVHP1C100R E 10UF, 16V C4046-50 ECJ2XC1H181J C 180PF, J, 50V C4051 ECJ2VF1H104Z C 0.1UF, Z, 50V C4052-54 ECA1CEN100 E 10UF, 16V C4056,57 ECJ2VF1H104Z C 0.1UF, Z, 50V C4101-04 ECJ2XC1H561J C 560PF, J, 50V C4105,06 ECJ2XC1H271J...
Page 34
Ref. No. Part No. Part Name & Description Pcs Remarks C6066-69 ECJ1XF1C104Z C 0.1UF, Z, 16V C6071,72 ECJ1XF1C104Z C 0.1UF, Z, 16V C6073 EEVHB0J101 E 100UF, 6.3V EEVHB0J101P C6074-76 ECJ1XF1C104Z C 0.1UF, Z, 16V C6077 ECJ1VF1A105Z C 1UF, Z, 10V C6078 ECJ1VB1H332K C 3300PF, K, 50V...
Page 35
Ref. No. Part No. Part Name & Description Pcs Remarks C9077-79 ECJ1VF1H103Z C 0.01UF, Z, 50V C9081 ECJ1XF1C104Z C 0.1UF, Z, 16V C9082-87 ECJ1VF1A105Z C 1UF, Z, 10V C9088 ECJ1XC1H470J C 47PF, J, 50V C9089-91 ECJ1XF1C104Z C 0.1UF, Z, 16V C9092 ECJ1VF1H103Z C 0.01UF, Z, 50V...
Page 36
Ref. No. Part No. Part Name & Description Pcs Remarks C9188 ECJ1XB1C104K C 0.1UF, Z, 16V C9190 ECJ1VF1A105Z C 1UF, Z, 10V C9191,92 ECJ1XC1H330J C 33PF, J, 50V C9193 EEVHB0G101 E 100UF 4V C9196,97 ECJ1VB1H103K C 0.01UF, K, 50V C9199 ECJ1XF1C104Z C 0.1UF, Z, 16V C9201...
Page 42
Ref. No. Part No. Part Name & Description Pcs Remarks R638 ERJ12YJ103 M 10KOHM,J, 1/2W ERJ12YJ103U R660,61 ERJ12NF2000 M 20 OHM, , 1/2W R801 ERJ6GEYJ103 M 10KOHM,J,1/10W R802 ERJ6GEYJ153 M 15KOHM,J,1/10W R803 ERJ6GEYJ102 M 1KOHM,J,1/10W R804 ERJ6ENF1781 M1.78KOHM, 1/10W R805 ERJ6ENF1102 M 11KOHM, 1/10W R806...
Page 43
Ref. No. Part No. Part Name & Description Pcs Remarks R1016 EXB38V680J RESISTOR ARRAY R1018 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R1019 ERJ3GEYJ0R00 M 0 OHM, 1/16W R1020 ERJ3GEYJ103 M 10KOHM,J,1/16W R1023 ERJ3GEYJ225V M 2.2MOHM,J,1/16W R1024 ERJ3GEYJ392 M 3.9KOHM,J,1/16W R1027 EXB38V680J RESISTOR ARRAY R1028 ERJ3GEYJ473...
Page 44
Ref. No. Part No. Part Name & Description Pcs Remarks R1096,97 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R1099 ERJ3GEYJ473 M 47KOHM,J,1/16W R1101 ERJ3GEYJ473 M 47KOHM,J,1/16W R1102 EXB38V473J RESISTOR ARRAY R1105 ERJ3GEYJ0R00 M 0 OHM, 1/16W R1107 ERJ3GEYJ103 M 10KOHM,J,1/16W R1111 ERJ6GEYJ562 M 5.6KOHM,J,1/10W R1112,13 ERJ3GEYJ103...
Page 45
Ref. No. Part No. Part Name & Description Pcs Remarks R2529,30 ERJ6GEYJ104 M 100KOHM,J,1/10W R2532 ERJ6GEYJ472 M 4.7KOHM,J,1/10W R3001 ERJ3GEYJ103 M 10KOHM,J,1/16W R3002,03 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R3004,05 ERJ3GEYJ103 M 10KOHM,J,1/16W R3006-10 ERJ3GEYJ473 M 47KOHM,J,1/16W R3012 ERJ3GEYJ473 M 47KOHM,J,1/16W R3013-20 EXB38V473J RESISTOR ARRAY...
Page 46
Ref. No. Part No. Part Name & Description Pcs Remarks R4109,10 ERJ6GEYJ333 M 33KOHM,J,1/10W R4111 ERJ6GEY0R00 M 0 OHM, 1/10W R4112 ERJ6ENF3301 M 3.3KOHM, 1/10W R4113 ERJ6GEYJ472 M 4.7KOHM,J,1/10W R4116 ERJ6GEYJ102 M 1KOHM,J,1/10W R4117 ERJ6ENF3301 M 3.3KOHM, 1/10W R4126,27 ERJ6GEYJ104 M 100KOHM,J,1/10W R4150,51 ERJ6GEYJ333...
Page 47
Ref. No. Part No. Part Name & Description Pcs Remarks R6060 ERJ3GEYJ102 M 1KOHM,J,1/16W R6061 ERJ3GEYJ0R00 M 0 OHM, 1/16W R6062 ERJ3GEYJ104 M 100KOHM,J,1/16W R6063 ERJ3GEYJ0R00 M 0 OHM, 1/16W R6064 ERJ3GEYJ392 M 3.9KOHM,J,1/16W R6065 ERJ3GEYJ0R00 M 0 OHM, 1/16W R6066 ERJ3GEYJ104 M 100KOHM,J,1/16W...
Page 48
Ref. No. Part No. Part Name & Description Pcs Remarks R9083 ERJ6ENF51R0 M0.51KOHM, 1/10W R9084 ERJ3GEYJ221 M 220 OHM,J,1/16W R9085 ERJ3GEYJ0R00 M 0 OHM, 1/16W R9086 ERJ3EKF1800 M 180 OHM, 1/16W R9087 ERJ6ENF51R0 M0.51KOHM, 1/10W R9088 ERJ6ENF68R0 M 68 OHM, 1/10W R9089 ERJ6ENF82R0 M 82 OHM, 1/10W...
Page 49
Ref. No. Part No. Part Name & Description Pcs Remarks R9149,50 ERJ3GEYJ0R00 M 0 OHM, 1/16W R9154 ERJ3GEYJ103 M 10KOHM,J,1/16W R9155 ERJ3GEYJ153 M 15KOHM,J,1/16W R9156 ERJ3GEYJ103 M 10KOHM,J,1/16W R9157 ERJ3GEYJ153 M 15KOHM,J,1/16W R9158 ERJ3GEYJ103 M 10KOHM,J,1/16W R9159 ERJ3GEYJ153 M 15KOHM,J,1/16W R9161 ERJ3GEYJ223 M 22KOHM,J,1/16W...
Page 50
ZA601-03 K4ZZ01000121 EARTH LUG Ref. No. Part No. Part Name & Description Pcs Remarks ZA661,62 K4ZZ01000121 EARTH LUG ZA6001-08 TESA169 SHIELD CLIP ZA6009-12 K4CD01000002 TERMINAL ZB001 TMME227 CLAMPER 11. Schematic Diagram for printing with A4 12. Cover for printing with A4...
Page 60
TO DG3 (DG-BOARD) Q608 T602 Q605 PA601 BACK LIGHT Q606 IC602 PWM CONTROL INV_DET FROM IC3002-41 (DG-BOARD) IC601 OP AMP INV_PWM Q601 FROM IC6004-98 (DG-BOARD) Q602 LIGHT ON TO A-BOARD FROM IC1001-97 (DG-BOARD) (OVER Q603,604 VOLTAGE PROTECT) TX-22LT3 Power Block Diagram...
Page 64
S2-2 21PIN SLOW V/Y OUT SCRAT AV2-Q-LINK C/PB OUT Q-LINK Q4001 MONIV VIDEO_OUT VIDEO IN VIDEO_IN V IN JK4001 L IN SDA1 R IN SCL1 Q4102 B-BOARD TV-V Q2102,Q2103 TNR001 VIDEO TUNER SDA1 SDA1 SCL1 SCL1 TX-22LT3 Signal Block Diagram...
Page 65
SDA1 EOOFER AMP RESQ RESQ SCL1 WOOFER AMP STB TO DG1 (DG-BOARD) C/PB C/PB GREEN BLUE IC4110 MUTE Q4156 MUTE CONT AV1-Q-LINK RESQ RESQ Q-LINK Q-LINK AV2-Q-LINK CONT Q-LINK_SEL Q-LINK SEL Q4155 SDA1 SDA1 SCL1 SCL1 TX-22LT3 Signal Block Diagram...
Page 86
ORDER NO. ITD0310055C2 LCD TV TX-22LT3 LH12 Chassis Power Source Aerial-Rear AC 100~240V, 50/60Hz Power Consumption Operating Conditions Average use: 67W Temperature: 41°F-95°F(5-35°C) Stand-by condition: 1.8W Humidity: 5%-90% RH (non-condensing) TV set DC 15V, 3.8 A max. Connection Terminals AV1 (Scart connecter)
TX-22LT3 1 Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
TX-22LT3 2 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
TX-22LT3 3 Self Check 1. Self-Check is used to automatically check the bus lines and hexadecimal code of the TV set. 2. To get into the Self -Check mode press the Down ( ) button on the customer controls at the front of the set, at the same time pressing the Recall button on the remote control, and the screen will show : If the CCU ports have been checked and found to be incorrect or not located then “--”...
TX-22LT3 4 Chasis Board Layout Board Name Function A-Board Main (DC Power Supply, Audio, Input Select, AV Connector) B - Board Tuner DG - Board Global Core, RGB Processor, Micro Processor, Pixel Converter) K - Board Switch PD - Board...
TX-22LT3 5 Servicing method 5.1. Removing the tilt base 1. Lay down the main unit so that the rear cover faces upward. 2. Remove the AV cable cover. 3. Remove the tuner cable cover. 5.2. Removing the rear cover 1. Remove the tilt base. (See 5.1.) 2.
TX-22LT3 5.4. Removing the PH shield plate 5.6. Removing the V-Board and the PD shield plate 1. Remove the speaker box. (See 5.5.) 2. Disconnect the coupler (A5). 1. Remove the shield plate. (See 5.3.) 3. Remove the fixing screw (1pcs).
TX-22LT3 5.9. Removing the chassis 5.10. Removing the tuner cover and the terminal cover 1. Remove the PH shield plate and the PD shield plate. (See 5.4.) 1. Remove the rear cover. (See 5.2.) 2. Remove the V-Board. (See 5.6.) 2.
TX-22LT3 5.12. Removing the A-Board 5.14. Removing the DG-Board 1. Remove the shield plate. (See 5.3.) 1. Remove the shield plate. (See 5.3.) 2. Remove the angle. (See 5.5.) 2. Disconnect the couplers (DG1, DG2, DG3 and DG6900). 3. Remove the terminal cover. (See 5.10.) *When removing coupler (DG6900), cautions are required for the handling of a connector.
TX-22LT3 5.16. Removing the PD-Board 1. Remove the rear cover. (See 5.2.) 2. Remove the PD shield plate. (See 5.4.) 3. Disconnect the couplers (PD1, PD2, PD3 and PD5). 4. Remove the fixing screw (1pcs). 5. Remove the PD-Board. 5.17. Removing the LCD panel 1.
TX-22LT3 6 Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Mode. 6.1. How to enter SERVICE 1 1. In sound menu, set BASS to MAXIMUM, and set TREBLE to MINIMUM.
1.5V D817 D818 Q606 IC602 PWM CONTROL STB_2.5V INV_DET FROM IC3002-41 (DG-BOARD) IC601 OP AMP INV_PWM Q601 FROM IC6004-98 (DG-BOARD) Q602 LIGHT ON TO A-BOARD FROM IC1001-97 (DG-BOARD) (OVER Q603,604 VOLTAGE PROTECT) TX-22LT3 TX-22LT3 Power Block Diagram Power Block Diagram...
V IN JK4001 L IN Q-LINK SDA1 Q-LINK R IN AV2-Q-LINK CONT SCL1 Q-LINK_SEL Q-LINK SEL Q4155 Q4102 SDA1 SDA1 SCL1 SCL1 B-BOARD TV-V Q2102,Q2103 TNR001 VIDEO TUNER SDA1 SDA1 SCL1 SCL1 TX-22LT3 Signal Block Diagram TX-22LT3 Signal Block Diagram...
TNPA2897 TNPA2897 SEE REVERSE FOR ORDERNO. CAUTION HIGH VOLTAGE PH-BOARD (COMPONENT SIDE) TNPA2897 R660 C663 D661 CAUTION TNPA2897 HIGH C665 ORDER NO. VOLTAGE C660 C664 CAUTION C661 HIGH VOLTAGE D660 C662 R661 CONNECT PROPERLY TX-22LT3 TX-22LT3 PH-BOARD TNPA2897 PH-BOARD TNPA2897...