Page 1
HX260FC T3 FOREST MACHINE (HX260FC T3) This manual was produced by DAEMO engineering and some revisions have been made in HYUNDAI CONSTRUCTION EQUIPMENT...
Page 2
Hyundai Construction Equipment. To ensure safe use and maintenance of this equipment, please read and understand this User Manual before use. Contact Hyundai Construction Equipment if you have any questions about contents of this User Manual.
HX260FC T3 Contents Ⅰ. Safety 1. Basic Precautions 2. Dangerous Operations Ⅱ. Specifications 1. Name of Each Part 2. Forest Equipment 3. Hydraulic Circuit Diagram Ⅲ. Installation 1. Preparations Before Work Ⅳ. Operation 1. Operating Precautions 2. Operation of Lever and Pedal Ⅴ.
HX260FC T3 Ⅰ. Safety *Dangerous operations presented below are prohibited for safe use of this equipment. *Dangerous operations can arouse serious damaging or failure of the equipment. 1. Basic Precautions Check and gain full knowledge of safety labels in this Manual and on the equipment. Forest equipment must be maintained in standard state at all times, and no alteration is allowed.
Page 5
HX260FC T3 Prevention of burn After stopping the equipment, conduct inspection and maintenance once temperature of the equipment is cooled down. Be careful about getting burned by hot oil. Gear oil, operating oil, high pressure hose and other pipe parts reach high temperature during operation.
Page 6
HX260FC T3 Fire prevention Remove inflammable substances nearby the equipment. Inspect status of hydraulic pipes and leaking of operating oil, and perform maintenance and repair as necessary. Leakage of inflammable liquids such as fuel, lubricant and operating oil can cause fire. Inspect short circuit and damaging of electric wiring that cause spark, and keep connecting parts of power cables clean.
Page 7
HX260FC T3 Precaution for inspection and maintenance of hydraulic parts Stop the equipment on a flat and solid ground surface. Put attachments down on the ground and stop the engine. Do not perform maintenance immediately after work. Wait until the entire equipment is completely cooled down.
HX260FC T3 2. Dangerous Operations The work methods introduced below are not permitted for the safe use of the equipment. Such operations can cause serious damaging and failure of your equipment. Do not work over the permitted scope of work.
Page 9
HX260FC T3 Do not rotate the body using the grapple. Do not rotate the body using the boom cylinder or wood grapple. Do not move the grapple above people. Do not move the wood grapple above people’s head or truck operating room. Direct collision with the wood grapple or dropping of workpiece can lead to serious injury or damaging of truck.
Page 10
HX260FC T3 Do not rotate the wood grapple when it is touching the ground surface. Doing so can seriously damage the wood grapple, arm and connector. Do not operate hastily. Hasty operation can cause overturn of the equipment. Be careful to maintain stability of the...
Page 11
HX260FC T3 Do not drive at high speed on a rough flatland with uneven floor. If the floor is rough, frozen or uneven, drive as slow as possible. Driving at high speed can weigh excessive impact on the body and wood grapple.
HX260FC T3 Ⅲ. Installation 1. Preparations Before Work 1) Inspect the amount of hydraulic oil. If insufficient, fill the oil tank with enough hydraulic oil. 2) Check that the stop valve is opened. 3) Operate after checking that all bolts and nuts are tightened properly.
- Remove any obstacles within the work scope. - Do not perform dangerous operations presented in this Manual. - Contact Hyundai Construction Equipment for remodeling of the equipment. After work - During maintenance and repair, guarantee stable working conditions and equipment.- Inspect leaking of operating oil, cooling water and engine oil, as well as loosening of the hydralic hose, bolts and nuts.
If an abnormality is discovered during operation or inspection, identify the cause and perform maintenance immediately. If the cause is unclear or there is a problem in the hydraulic unit, contact Hyundai Construction Equipment. 2. Inspection Method - Be especially careful about safety.
HX260FC T3 3. Preparations Before Maintenance Before starting maintenance work described in this Manual, stop the equipment as below for maintenance unless described otherwise. - Place the equipment on a safe and flat place. - Attach a “Do not start” tag to the work lever.
HX260FC T3 5. Types and Causes of Ordinary Troubles Failure Type Cause of Failure Temperature of operating oil fails to reach normal level. RPM of the engine is too low. Flow of operating oil is low. There is an obstacle on the hydraulic line.
Page 23
PARTS MANUAL SPECIAL ATTACHMENT HX260FC T3...
Page 24
CONTENTS C. HYDRAULIC GROUP BOOM PIPING KIT(# 0009-) ----------------------- C070 GREASE PIPING KIT(# 0009-) ----------------------- C080 ----------------------- ARM PIPING KIT(# 0009-) C140 ATTACH PIPING KIT(# 0009-) ----------------------- C180 ----------------------- MAIN PIPING KIT(# 0009-) C300 MAIN PIPING KIT(# 0009-) ----------------------- C301 E.
MAIN PIPING KIT(#0009-) HX260FC T3 ITEM PART NO DESCRIPTION QTY SERIAL NO REMARK * XKBN-06490 PIPING KIT-MAIN STANDARD 1 XKBN-06393 . VALVE-RELIEF 2 XKBN-06394 . VALVE ASSY-REDUCING 3 XKBN-06395 . VALVE-FLOW CONTROL 4 XKBN-06396 . PIPE-MCV 5 XKBN-06397 . HOSE-P.D 6 XKBN-06398 .
Page 37
MAIN PIPING KIT (2/2)(#0009-) HX260FC T3 P2 PORT 5 22 T PORT 8 15 P1 PORT 6 22 T PORT 12 13 B PORT A PORT A PORT 9 19 P PORT 10 13 B PORT 11 13 MCV D5...
SUPPORT & SIDE COVER PART HX260FC T3 ITEM PART NO DESCRIPTION QTY SERIAL NO REMARK * XKBN-06365 COVER-SIDE&SUPPORT PART 1 XKBN-06314 . BOX ASSY-TOOL 2 XKBN-06315 . GUARD-REAR 3 XKBN-06316 . COVER-FRONT SIDE LH 4 XKBN-06317 . COVER ASSY-REAR SIDE LH 5 XKBN-06318 .
Page 76
SUPPORT & SIDE COVER PART HX260FC T3 ITEM PART NO DESCRIPTION QTY SERIAL NO REMARK * XKBN-06365 COVER-SIDE&SUPPORT PART 1 XKBN-06314 . BOX ASSY-TOOL 2 XKBN-06315 . GUARD-REAR 3 XKBN-06316 . COVER-FRONT SIDE LH 4 XKBN-06317 . COVER ASSY-REAR SIDE LH 5 XKBN-06318 .
FRONT PART SUPPORT & SIDE COVER HX260FC T3 SECTION A-A G310...
Page 78
FRONT PART SUPPORT & SIDE COVER HX260FC T3 ITEM PART NO DESCRIPTION QTY SERIAL NO REMARK * XKBN-06366 COVER-FRONT&SUPPORT PART 1 XKBN-06342 . BOOM ASSY 2 XKBN-06343 . STOPPER ASSY-BOOM CYLINDER 3 XKBN-06344 . PIPE-HARNESS GUIDE 4 XKBN-05679 . COVER-WORK LAMP 5 XKBN-06345 .
Page 80
UNDER COVER PART HX260FC T3 ITEM PART NO DESCRIPTION QTY SERIAL NO REMARK * XKBN-06304 COVER-UNDER 1 XKBN-06305 . COVER-FRONT UNDER LH 2 XKBN-06306 . COVER-FRONT UNDER LH 3 XKBN-06307 . COVER-REAR UNDER LH 4 XKBN-06308 . COVER-MIDDLE UNDER 5 XKBN-06309 .
MAIN FRAME GROUP HX260FC T3 ITEM PART NO DESCRIPTION QTY SERIAL NO REMARK * XKBN-06364 FRAME-MAIN PART 1 XKBN-06303 . FRAME ASSY-MAINE 2 XKBN-06304 . COVER-UNDER G490...
FRONT ATTACH KIT(#0009-) HX260FC T3 ITEM PART NO DESCRIPTION QTY SERIAL NO REMARK * XKBN-06462 ATTACH KIT-FRONT STRAIGHT 1 XKBN-06415 . BOOM ASSY SEE PH020, 5.7M 2 XKBN-06417 . ARM ASSY SEE PH030, 3.8M 3 XKBN-06491 . PIPING KIT-BOOM SEE PC070 4 XKBN-06492 .
Page 97
FRONT ATTACH KIT(2/2)(#0009-) HX260FC T3 SECTION A-A SECTION B-B SECTION C-C SECTION D-D H120-1 H120...
Page 98
FRONT ATTACH KIT(#0009-) HX260FC T3 ITEM PART NO DESCRIPTION QTY SERIAL NO REMARK * XKBN-06462 ATTACH KIT-FRONT STRAIGHT 1 XKBN-06415 . BOOM ASSY SEE PH020, 5.7M 2 XKBN-06417 . ARM ASSY SEE PH030, 3.8M 3 XKBN-06491 . PIPING KIT-BOOM SEE PC070 4 XKBN-06492 .
Page 99
NUMERICAL PART INDEX PART NO PAGE ITEM PART NO PAGE ITEM PART NO PAGE ITEM 21K6-42402 G120 18 S017-16035D H011 11 XKBN-00065 C300 21K8-00760 G120 23 S017-16040D H011 13 XKBN-00079 C080 21K8-31301 G120 24 S017-20030D H011 14 XKBN-00085 C070 21K8-41301 G020 41 S035-082026 C080...
Page 100
NUMERICAL PART INDEX PART NO PAGE ITEM PART NO PAGE ITEM PART NO PAGE ITEM XKBN-05656 G310 6 XKBN-06145 G300 33 XKBN-06215 G020 XKBN-05656 H120 6 XKBN-06145 G370 11 XKBN-06216 G020 XKBN-05674 G300 15 XKBN-06163 G300 27 XKBN-06216 G120 XKBN-05679 G310 4 XKBN-06166 G300...
Page 101
NUMERICAL PART INDEX PART NO PAGE ITEM PART NO PAGE ITEM PART NO PAGE ITEM XKBN-06253 G030 3 XKBN-06290 G570 27 XKBN-06329 G300 XKBN-06254 G030 4 XKBN-06291 G570 28 XKBN-06330 G300 XKBN-06255 G030 5 XKBN-06292 G570 29 XKBN-06331 G300 XKBN-06256 G030 6 XKBN-06293 G570...
Page 102
NUMERICAL PART INDEX PART NO PAGE ITEM PART NO PAGE ITEM PART NO PAGE ITEM XKBN-06366 G310 * XKBN-06403 C301 11 XKBN-06437 C070 XKBN-06367 E010 * XKBN-06404 C300 15 XKBN-06439 C140 XKBN-06369 C180 1 XKBN-06405 C300 17 XKBN-06440 C140 XKBN-06370 C180 2 XKBN-06406 C300...
Page 103
NUMERICAL PART INDEX PART NO PAGE ITEM PART NO PAGE ITEM PART NO PAGE ITEM XKBN-06480 C080 XKBN-06481 C080 XKBN-06489 C180 XKBN-06490 C300 XKBN-06491 C070 XKBN-06491 H120 XKBN-06492 C140 XKBN-06492 H120 XKBN-06493 C080 XKBN-06493 H120 XKBN-06494 C301 Y020-100111 H020 Y020-100111 H030 Y470-120000 C070...