Related Manuals for Hyundai CUT- 401
Summary of Contents for Hyundai CUT- 401
- Page 1 DC INVERTER PLASMA CUTTER CUT- 401 User Manual Original Instructions For Your Safety Read and understand this manual before use. Keep this manual for future reference. HYUNDAI...
- Page 2 CUT-401 We are still constantly improving this welder, therefore, some parts of this welder may be changed in order to achieve the better quality, but the main functions and operations will not be alternated and changed. Your understanding would be greatly appreciated.
-
Page 3: Table Of Contents
CUT-401 Table of Contents Safety General Description Main Parameters ............................Operation Control and Description ......................Installation Debugging and Operation Caution Maintenance Troubleshooting Exploded Drawing ............................1 0 HYUNDAI... -
Page 4: Safety
• Have a fire extinguisher nearby, and have a trained person to use it. • Airtight container welding is forbidden • Must not use the machines for other purposes except welding, such as pipe thawing, battery charging, heating. HYUNDAI... - Page 5 • Do not move the shielding gas bottle when the control valve is in place. Fix the gas bottle securely in an upright position to a separate wall rack or bottle cart. • Always close the gas bottle after use. Electrical connection must be performed by qualified personnel in accordance with relevant national and local regulations. HYUNDAI...
-
Page 6: General Description
Rate Output Current & Voltage 40A/96V No-load Voltage M Rated Duty Cycle (%) Protection Class IP21S Insulation Class HF Oscillating Pilot Arc Model Burner Inter Diameter (mm) Pressure of Air Compressor (kg) Cutting thickness (mm) 1-12 Net weight (kg) HYUNDAI... -
Page 7: Operation Control And Description
4. Operation Control and Description Temperature indicator Power indicator Power switch Output current adjustment gas-electric Earth Air plug intergrated connector clamp CUT-401 The panel picture above is for reference only. If any difference with the real machine, please follow with the real machine. HYUNDAI... -
Page 8: Installation Debugging And Operation
2) Avoid using in sunshine and rainy environment. 3) Keep machine dry and avoid water into machine. 4) Do not use the cutting machine in environment where is polluted with high density of dust or corrosive gas in the air. HYUNDAI... -
Page 9: Caution
Then machine will be operated normally. Avoid toppling over. Make sure the welding power source shall not be placed on tilted plane. &caution Creepage-protecting switch should be added when you are using the machine HYUNDAI... -
Page 10: Maintenance
To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. T hey can take this product for environmental safe recycling. HYUNDAI... -
Page 11: Troubleshooting
3. Check the high voltage diode on the bottom board not lit. 4. Check if HF electric capacity 102/10 KV is leaking 5. Check if relay is damaged. 1. Input voltage is too low. Arc is not starting. 2. Pressure of air compressor is too high or low. HYUNDAI... -
Page 12: Exploded Drawing
19. Screw M6*16 41. Screw M5X20 25. Fan 20. Bottom case 42. Side wind shield board 30. Middle board 21. Insulation bottom board 43. Screw M4X16 47. Top board 22. Copper stud 18*6 44. Top insulation board 53. Solenoid valv HYUNDAI... - Page 13 CUT-401 HYUNDAI...
- Page 14 HYUNDAI DC Inverter PLASMA CUTTER Declaration Conformity 2016 HYUNDAI Corporation 25, Yulgok-ro 2-gil, Jongno-gu, Seoul 03143 Korea Declare that the product detailed below : DC INVERTER PLASMA CUTTER MODEL : CUT-401 Satisfies the requirements of the Council Directives : EC-Low voltage directive 2014/35/EU...
- Page 16 25, Yul g ok-ro 2- g il, Jon g no- g u, Seoul 0 3 143, Korea, Post Code : 0 3 143 + 822390 1 114 www.h y undaicor p .com Co py ri g ht HYUNDAI Cor p oration All ri g hts reserved. Made in P.R.C HYUNDAI...