Related Manuals for KitchenAid 5KSM65 Series
Summary of Contents for KitchenAid 5KSM65 Series
- Page 1 Stand Mixer 5KSM65XX W11428517A.indd 1 W11428517A.indd 1 3/30/2020 12:03:39 PM 3/30/2020 12:03:39 PM...
-
Page 2: Parts And Features
PARTS AND FEATURES Motor Head Attachment Knob Speed Control Lever Attachment Hub (see the “Optional Attachments” Beater Height Adjustment Screw section) Bowl Support Flat Beater Locating Pins Flex Edge Beater* Stainless Steel Bowl** Wire Whip Beater Shaft Spiral Dough Hook Bowl Lift Lever (not shown) * Included with select models only. -
Page 3: Product Safety
PRODUCT SAFETY IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. Misuse of appliance may result in personal injury. 2. To protect against risk of electrical shock, do not put Stand Mixer in water or other liquid. -
Page 4: Electrical Requirements
PRODUCT SAFETY 12. Remove the Beaters, Wire Whip, or Spiral Dough Hook from the Stand Mixer before washing. 13. Never leave the appliance unattended while it is in operation. 14. Refer to the “Care and Cleaning” section for instructions on cleaning the surfaces in contact with food. -
Page 5: Accessory Guide
ACCESSORY GUIDE Operating Accessory Use to Mix Description time Flex Edge Beater Normal to Cakes, Creamed frostings, Candies, Flat Beater heavy mixtures Cookies, Biscuits, Pie pastry, Meat 1-10 minutes loaf, Mashed potatoes. Spiral Dough Hook Mixing and Breads, Rolls, Pizza dough, Coffee kneading yeast cakes buns. -
Page 6: Product Assembly
PRODUCT ASSEMBLY Turn the Stand Mixer to “0” (OFF) and then Place bowl lift lever in down position. unplug. IMPORTANT: If the bowl is not securely snapped into place, it will be unstable and wobble during use. Locating pin Spring latch To Attach the Bowl: Fit the bowl supports over locating pins and press down on back of the bowl until bowl pin snaps into spring... -
Page 7: Product Usage
PRODUCT USAGE BEATER TO BOWL CLEARANCE Your Stand Mixer is adjusted at the factory so the Flat Beater just clears the bottom of the bowl. If, for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, you can correct clearance easily. -
Page 8: Optional Attachments
OPTIONAL ATTACHMENTS KitchenAid offers a wide range of optional attachments such as the Spiralizer, Pasta Cutters, or Food Grinder that may be attached to the Stand Mixer attachment power hub as shown below. Turn the Stand Mixer to “0” (OFF) and then Remove the Attachment Hub cover. -
Page 9: Product Disassembly
PRODUCT DISASSEMBLY Turn the Stand Mixer to “0” (OFF) and then Press accessory upward and turn to the left. unplug. Pull down the accessory from Beater Shaft. Place Bowl-Lift Lever in the down position. Grasp bowl handle and lift straight up and off Locating Pins. -
Page 10: Care And Cleaning
CARE AND CLEANING IMPORTANT: Do not immerse the Stand Mixer body in water or other liquids. The following parts are Dishwasher-safe Turn the Stand Mixer to “0” (OFF) and then parts, top rack only: unplug. Stainless Steel Bowl**, Flat Beater, Flex Edge Beater* and Spiral Dough Hook. -
Page 11: Troubleshooting Guide
TROUBLESHOOTING GUIDE WARNING Electrical Shock Hazard Plug into an earthed outlet. Do not remove an earth prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, re, or electrical shock. Problem Solution Under heavy loads with extended mixing time periods, you... - Page 12 ©2020 KitchenAid. All rights reserved. KITCHENAID and the design of the Stand Mixer are trademarks in the U.S. and elsewhere. W11428517A 03/20 W11428517A.indd 12 W11428517A.indd 12 3/30/2020 12:03:43 PM 3/30/2020 12:03:43 PM...