Table of Contents
Advertisement
Turn the key to position 2 in the ignition lock
X
(
page 138).
Y
Select one of buttons ; to ? to control the
X
garage door drive.
To start programming mode: press and
X
hold one of buttons ; to ? of the integrated
garage door opener.
The garage door opener is now in program-
ming mode. After a short time, indicator
lamp : begins to light up yellow.
Indicator lamp : lights up yellow immedi-
ately the first time button ;, = or ? is pro-
grammed. If the selected button has already
been programmed, indicator lamp : lights
up yellow after ten seconds have elapsed.
Release button ;, = or ?. Indicator
X
lamp : flashes yellow.
To program the remote control: point
X
garage door remote control A towards but-
tons ; to ? on the rear-view mirror at a dis-
tance of 5 to 20 cm.
Press and hold button B on remote control
X
A until indicator lamp : lights up green.
When indicator lamp : lights up green: pro-
gramming is finished.
When indicator lamp : flashes green: pro-
gramming was successful. The next step is to
synchronise the rolling code (
Release button B of remote control A of the
X
garage door drive.
If indicator lamp : lights up red: repeat the
programming process for the corresponding
button on the rear-view mirror. When doing
so, vary the distance between remote control
A and the rear-view mirror.
The required distance between remote con-
trol A and the integrated garage door opener
depends on the garage door drive system.
Several attempts may be required. You
should test every position for at least
25 seconds before trying another position.
Synchronising the rolling code
Observe the "Important safety notes"
(
page 284).
Y
If the garage door system uses a rolling code,
you will also have to synchronise the garage
door system with the integrated garage door
opener in the rear-view mirror. To do this, you
will need to use the programming button on the
door drive control panel. The programming but-
ton may be placed at different locations depend-
ing on the manufacturer. It is usually located on
the door drive unit on the garage ceiling.
Familiarise yourself with the garage door drive
operating instructions, e.g. under "Program-
ming of additional remote controls", before car-
rying out the following steps.
Your vehicle must be within range of the garage
door or gate opener drive. Make sure that nei-
ther your vehicle nor any persons/objects are
present within the sweep of the door or gate.
Turn the key to position 2 in the ignition lock
X
(
Y
Get out of the vehicle.
X
Press the programming button on the door
X
drive unit.
Usually, you now have 30 seconds to initiate
the next step.
Get into the vehicle.
X
Press previously programmed button ;, =
X
or ? of the integrated garage door opener
until the door closes.
The rolling code synchronisation is then com-
plete.
Problems when programming
If you have problems when programming the
integrated garage door opener, please note the
page 285).
Y
following:
Check the transmitter frequency used by
R
garage door drive remote control A and
whether it is supported. The transmitter fre-
quency can usually be found on the back of
the garage door drive remote control.
Replace the batteries in garage door remote
R
control A. This increases the likelihood that
garage door remote control A will transmit a
strong and precise signal to the integrated
garage door opener in the rear-view mirror.
When programming, hold remote control A
R
at varying distances and angles from the but-
ton which you are programming. Try various
angles at a distance between 5and 20 cm or
at the same angle but at varying distances.
If there is another remote control for the same
R
garage door drive, perform the programming
steps again using this remote control. Before
performing these steps, make sure that new
batteries have been fitted in garage door drive
remote control A.
Note that some remote controls transmit only
R
for a limited period (the indicator lamp on the
remote control goes out). Press button B on
page 138).
Features
285
Z
Advertisement
Table of Contents
