Setting The Digital Input (Digital In) Terminals-Digital In1/2; Setting Auto Surround-Auto Surrnd; Setting The Auto Function Mode-Auto Mode - JVC RX-E51BEB Instructions Manual

Setting the digital input (DIGITAL IN)
terminals—DIGITAL IN1/2
When you use the digital input terminals, register what
components are connected to which terminals—DIGITAL IN1/2
(see page 9) so that the correct source name will appear when
you select the digital source.
For DIGITAL IN 1(DVR/DVD) terminal:
EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
LPCM L C R PL
DOLBY D NEO : 6
S . WFR LFE
DTS AAC DSP 3D
LS SB RS
96 / 24 AUTO SR
DVR/DVD
VIDEO
TV
(Back to the beginning)
For DIGITAL IN 2(VIDEO) terminal:
EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
LPCM L C R PL
DOLBY D NEO : 6
S . WFR LFE
DTS AAC DSP 3D
LS SB RS
96 / 24 AUTO SR
VIDEO* VCR*
DVR/DVD*
* The one selected for "DIGITAL IN1" will be skipped.
DVR/DVD For DVD player (or DVD recorder).
VIDEO For the component connected to the VIDEO IN jack
on the rear of the receiver.
VCR For VCR.
TV For TV.
Initial setting: DVR/DVD (for "DIGITAL IN1")
VIDEO (for "DIGITAL IN2")
Setting Auto Surround—AUTO SURRND
You can enjoy the Surround mode simply by selecting the source
(with digital input selected for that source).
• Auto Surround also works when the input mode changes from
analogue to digital.
• For details about the Surround/DSP modes, see pages 29 to 31.
Select "AUTO SR: ON" when activating Auto Surround.
AUTO SR: ON
The AUTO SR indicator lights up on the display.
• If a multi-channel signal comes in, an appropriate
Surround mode will be turned on.
• If a Dolby Digital 2-channel or DTS 2-channel signal
with surround signal comes in, "PLII MOVIE" will be
selected.
• If a Dolby Digital 2-channel or DTS 2-channel signal
without surround signal comes in, "SURRND OFF
(stereo)" will be selected.
• If a Linear PCM signal comes in, nothing will
change.
AUTO SR:OFF
Select to deactivate Auto Surround.
Initial setting: AUTO SR:OFF
AUTO MUTING SLEEP AUTO MODE
ATT
HP
MHz
kHz
VCR
AUTO MUTING SLEEP AUTO MODE
ATT
HP
MHz
kHz
TV*
(Back to the beginning)
NOTES
• This function does not take effect in the following cases:
– While playing an analogue source,
– While selecting any of DSP modes (see page 31), or one of
the fixed digital decode mode—"DGTL D.D." or "DGTL DTS"
(see page 11), and
– While listening with the headphones.
• If you press SURROUND with Auto Surround activated, Auto
Surround will be canceled temporarily for the currently selected
source.
Auto Surround setting will be restored in the following cases:
– When you turn the receiver off and on,
– When you change the source,
– When you change the analogue/digital input, and
– When you select "AUTO SR: ON" again.
Setting the Auto Function mode
—AUTO MODE
The source will be selected automatically simply by turning on a
video component.
• This function takes effect for the video components connected
to the receiver using the SCART cable—DVR/DVD and VCR.
Auto Function mode works as follows:
• When a video component is turned on, the receiver selects the
video component as the source (and the TV input is changed
automatically).
• When a video component currently selected as the source is
turned off, the receiver changes the source to the video source
previously selected—DVR/DVD, VCR, or VIDEO.
MODE: AUTO1 Auto Function mode works when the receiver
is turned on or when TV Direct is activated.
MODE: AUTO2 Auto Function mode works when the receiver
is turned on or off, or when TV Direct is
activated. (When a video component is turned
on while the receiver is off, TV Direct is
activated and the receiver selects the video
component as the source.)
MODE:MANUAL You need to select the source manually.
Initial setting: MODE:MANUAL
When "MODE: AUTO1" or "MODE: AUTO2" is selected, the AUTO
MODE indicator lights up on the display.
NOTES
• When selecting VCR as the source, "MODE: AUTO1" or "MODE:
AUTO2" may not work if you only turn on the VCR. If this
happens, you may need to start playback to activate Auto
Function mode.
• When Auto Function mode is set to "MODE: AUTO2," the TV
Direct may be activated after recovery from a power failure.
19