Changing The Display Brightness; Turning Off The Power With The Sleep Timer; Making Sounds Natural - JVC RX-D301S Instructions Manual

Changing the display brightness

You can dim the display—Dimmer.
From the remote control ONLY:
Press DIMMER repeatedly.
• Each time you press the button, the display brightness changes
as follows:
DIMMER 1: Dims the display.
DIMMER 2: Dims the display more than DIMMER 1.
DIMMER 3: Turns off the display.
(Temporarily canceled when you operate the
receiver.)
DIMMER OFF: Cancels the Dimmer (normal display).
Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
• Each time you press the button, the shut-off time changes in 10
minute intervals. The SLEEP indicator lights up on the display.
ANALOG
AUTO SURR
L R
S.WFR
10min 20min 30min 40min 50min 60min
OFF (canceled)
90min
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off
time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly so that "SLEEP OFF" appears on the
display. (The SLEEP indicator goes off.)
• The Sleep Timer is also canceled when you turn off the
receiver.

Making sounds natural

JVC's CC (Compression Compensative) Converter eliminates
jitter and ripples, achieving a drastic reduction in digital distortion
by processing the digital music data in 24 bit-quantization and by
expanding the sampling frequency to 176.4 kHz (for fs 44.1 kHz
signals)/192 kHz (for fs 48 kHz signals) on the front speakers.
By using the CC Converter, you can obtain a natural sound field
from both digital and analog sources.
Press CC CONVERTER repeatedly.
• Each time you press the button, the mode changes as follows:
CC CNVRTR 1: Select when playing back an analog
source or a digital source with non
compressed digital sound signal (Linear
PCM).
The CC CONVERTER 1 indicator lights
up on the display.
CC CNVRTR 2: Select when playing back a source with
compressed digital sound signal (Dolby
Digital or DTS).
The CC CONVERTER 2 indicator lights
up on the display.
CC CNVRTR OFF: Select when not using the CC Converter.
16
NOTE
When "DVD MULTI" is selected as the source, this function is not
available.
SLEEP indicator
SLEEP
80min 70min
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power, and
• when you change the source.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analog/digital input mode (see page 14)
• Bass boost (see page 25)
• Digital equalization pattern (see page 24)
• Input attenuator mode (see page 25)
• Midnight mode (see page 21)
• Speaker output level (see page 24)
• Surround/DSP mode selection (see page 33)
NOTE
If the source is FM or AM, you can assign a different setting
for each band.
Signal and speaker indicators on the display
Signal indicators
L C R
S.WFR LFE
ANALOG DUAL MONO
DIGITAL AUTO
L C
LS S RS
LINEAR PCM
S.WFR
DIGITAL
LS S
SB
SB SB
96 / 24
SB SB
The signal indicators light up as follows:
L: • When digital input is selected: Lights up when the
left channel signal comes in.
• When analog input is selected: Always lights up.
R: • When digital input is selected: Lights up when the
right channel signal comes in.
• When analog input is selected: Always lights up.
C: Lights up when the center channel signal comes in.
LS: Lights up when the left surround channel signal comes
in.
RS: Lights up when the right surround channel signal comes
in.
S: Lights up when monaural surround signal comes in.
SB: Lights up when the surround back channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
NOTE
When "DVD MULTI" is selected as the source, all the signal
indicators except "SB," "S," and "LFE" light up.
The speaker indicators light up as follows:
• The subwoofer indicator (
S.WFR
"SUBWOOFER" is set to "SUBWFR
see page 19.
• The other speaker indicators light up only when the
corresponding speaker is set to "SML (small)" or "LRG
(large)," and also when required for the current playback.
Speaker indicators
L C R
S.WFR LFE
AUTO SURR
R
HEADPHONE
LS S RS
PL x
LFE
NEO : 6 DSP
RS
3D-PHONIC SB
SB SB
SB
VIRTUAL SB
) lights up when
< >
YES ." For details,