Audio/Mic[2/2] Menu Screen; Lcd/Vf[1/4] Menu Screen - JVC GY-HD250 Instructions Manual

MENU SCREENS
AUDIO/MIC[2/2] Menu
Screen
In VTR mode, the screen changes to the AUDIO menu screen.
Item Function/Setting (bold characters indicate initial settings)
AUDIO MONITOR Selects whether stereo or mixed audio is output from the PHONES jack when the MONITOR SELECT switch is set
to BOTH.
STEREO : Stereo audio (CH-1 audio is output to L and CH-2 audio is output to R)
* Outputs only the CH-1 audio from the monitor speaker.
MIX : Mixed audio (CH-1 and CH-2 mixed audio is output to L and R)
FAS AUDIO Selects the recording level adjusting method for FAS (Full Auto Shooting). (CH-1, CH-2)
AUTO : Sets to AUTO.
SW SET : Follows settings for the AUDIO SELECT switch.
X See "2 [CH-1/CH-2 AUDIO SELECT] switch" on page 13.
X See "g [FULL AUTO] switch" on page 19.
SEARCH AUDIO [DV] Selects whether to output audio when searching a tape recorded in DV format. (This also includes slow playback.)
ON : Audio is output.
OFF : Audio is not output.
PB AUDIO CH [DV] Selects which channel audio to output when playing back a DV tape with the audio signal recorded in 4 channels.
(Can only be set in VTR mode)
CH1/2 : Outputs the CH-1 and CH-2 channel audio.
GY-HD250/GY-HD251 records the audio in CH-1 and CH-2 while shooting.
MIX : Outputs all 4 channels of audio at the same time.
CH3/4 : Outputs the CH-3 and CH-4 channel audio.
MEMO
GY-HD250/GY-HD251 does not have a function for dubbing to the CH-3 and CH-4 channels.
PAGE BACK When the cursor is in this position, press the SHUTTER dial to the AUDIO/MIC[1/2] menu screen.
88

LCD/VF[1/4] Menu Screen

The LCD/VF menu screen consists of four screens. (1/4 screen, 2/4 screen, 3/4 screen, 4/4 screen)
The LCD/VF[1/4] menu screen can only be set in camera mode.
In VTR mode, this screen consists of two screens. (1/2 screen, 2/2 screen)
Item Function/Setting (bold characters indicate initial settings)
ZEBRA Switches the luminance level of the subject sections where the zebra pattern is displayed.
60-70% : Zebra pattern is displayed in sections with luminance levels between 60% and 70%.
70-80% : Zebra pattern is displayed in sections with luminance levels between 70% and 80%.
85-95% : Zebra pattern is displayed in sections with luminance levels between 85% and 95%.
OVER95% : Zebra pattern is displayed in sections with luminance levels over 95%.
OVER100% : Zebra pattern is displayed in sections with luminance levels over 100%.
F. NO/IRIS IND. Selects whether or not the F-number of the lens iris/iris level mark is displayed in the status display on the LCD mon-
itor or in the viewfinder. (STATUS 1 screen)
OFF : F-number and iris level mark is not displayed.
F.NO : F-number is displayed.
F.NO+IND. : F-number and iris level mark is displayed.
FILTER Selects whether or not the FILTER position of this device is displayed in the status display on the LCD monitor or in
the viewfinder. (STATUS 1 screen)
OFF : FILTER position is not displayed.
ON : FILTER position is displayed.
*1 Selects whether or not the safety zone is shown on the LCD monitor or in the viewfinder together with the form of
SAFETY ZONE
the safety zone indication.
OFF : Not displayed.
4:3 : 4:3 zone is displayed.
14:9 : 14:9 zone is displayed.
16:9 : 16:9 zone is displayed.
16:9+4:3 : 16:9 zone and 4:3 zone are display mixed. (This cannot be selected when DV format is set.)
2.35:1 CE : Displays 2.35:1 zone in the middle of the screen.
(Only in HDV format or 24P or 25P mode)
2.35:1 CH : Displays 2.35:1 zone at the top of the screen.
(Only in HDV format or 24P or 25P mode)
*1 Sets whether or not a center mark is displayed when the safety zone is displayed.
CENTER MARK
ON : Center mark is displayed.
OFF : Center mark is not displayed.
MEMO
When the SAFETY ZONE item is set to OFF, "- - -" is indicated and this item cannot be selected.
FOCUS ASSIST Sets the FOCUS ASSIST function. Press the [FOCUS ASSIST] button on page 14 (6) or page 18 (7) to operate
the FOCUS ASSIST function.
NORMAL : Only the [FOCUS ASSIST] function operates.
(The focus area becomes blue, red or green, making it easier to focus.)
ACCU-FOCUS : The FOCUS ASSIST function and ACCU-FOCUS (forced focus) function operates.
This makes the depth of field shallower, making it easier to focus. ACCU FOCUS automatically
turns OFF after approximately 10 seconds.
COLOR Sets the display color for focusing when running the FOCUS ASSIST function.
BLUE : Displays the area of focus in blue.
RED : Displays the area of focus in red.
GREEN : Displays the area of focus in green.
LEVEL Sets the display range of the focal area when the FOCUS ASSIST function is in use.
LOW : Displays the focal area narrower than MIDDLE.
MIDDLE : Displays the focal area in normal setting.
HIGH : Displays the focal area wider than MIDDLE.
NEXT PAGE When you display the LCD/VF[2/4] menu screen, move the cursor to this position and press the SHUTTER dial.
PAGE BACK When the cursor is in this position, press the SHUTTER dial to return to the TOP MENU screen.
*1
SAFETY ZONE and CENTER MARK will not be displayed when this device is in VTR mode (PLAY, STL, FWD, REV).
89