Page 1
WHEEL BALANCER USER MANUAL Pls read this manual before operation...
Page 2
The operation manual made for you can give you the instructions on how to use and maintenance the machine. It will directly effect the entire functions and the endurance of the machine. Before operate the machine, carefully read the following instructions. Series number:CB460X Model.: Manufacturing date.:...
CONTENT WARNING------------------------------------------------------------------------------------- -------------------------------------------------1 INTRODUCTION------------------------------------------------------------------------------------ -----------------------------------------1 INSTALLATION------------------------------------------------------------------------------------- -----------------------------------------2 ELECTRICATION CONNECTION------------------------------------------------------------------------------------------------------2 SAFETY REGULATION-------------------------------------------------------------------------------------------------------------------3 BRIEF INTRODUCTION ON THE WHEEL BALANCER-------------------------------------------------------------------------3 MEANING OF THE SCALE---------------------------------------------------------------------------------------------------------------3 APPEARANCE OF THE MACHINE----------------------------------------------------------------------------------------------------4 CHARACTERISTIC AND FUNCTION--------------------------------------------------------------------------------------------------4 OPERATION NOTE----------------------------------------------------------------------- --------------------------------------------------5 GENERAL-------------------------------------------------------------------------------------------- -----------------------------------------5 TRANSPORT--------------------------------------------------------------------------------------- -------------------------------------------6 DETACHING THE PACKAGE------------------------------------------------------------------------------------------------------------6 OPERATION OF THE MACHINE --------------------------------------------------------------------------------------------------------7 TRANSPORTATION AND INSTALLATION -------------------------------------------------------------------------------------------7 HANDOVER NOTE----------------------------------------------------------------------------- ---------------------------------------------7 CABLE OF THE MACHINE ---------------------------------------------------------------------------------------------------------------7...
WARNING NOTE On the condition that confirm the operation of the Can cause the dangerous of slight injuries or machine including the operation system, tools damage to the subject and operation unsafe. and accessories operated properly and/or without being damaged, you can have some period limit Carefully read the instruction before use the of the guarantee during which the manufacturer machine.
following methods described. INSTALLATION Electrical connect Detach the package, lift and install the machine in accordance with the following instruction. Any electrical connect to the machine will be only executes by the qualified personnel and should It will damage the machine or endanger the be in accordance with the current regulation.
-Do not remove or abrade any label of the Safety regulation warning and instruction on the danger or replace the label missing or fuzzy. You must get the label from your nearest dealer if any label is missing or damaged. It will cause the serious injuries to the operators -Check the use and the relative accident and the other persons if not in accordance to the...
performance • Apply the central synthesis signal manage system with the characteristic of high intelligent and long life. rotation part • Main shaft adopts the high quality bearing with This label is near the balance shaft and hint the the characteristic of low noise and high precision. operator that this is a rotation part which is •...
Machine start when optional Adapt different 28 Max. wheel weight 130kg hood lower down model 29 Package size 1300mmX1000m Outer package Quick nut with standard Adapt different mX1150mm handle model 30 Weight of the 240KG net weight 10 Caliper/weight/han standard Adapt different machine 31 Temperature...
unbalance position. The range of the periodically maintenance to avoid the damage measurement see the part of the technical data. and accident. Note the following issues • Do not detach the wheel balancer by yourselves. • Do not collide the rotation part of the shaft Any instruction not specified in the manual is considered to be impropriate and unreasonable operation.
or not. A、When transport the machine, be careful to •Remove the anchor bolt and detach the wheel avoid the scratch and collide of the machine. balancer but we cannot carry the mail shaft of B、Carefully check if there are any damage or the wheel balancer.
frequency stabilizer to keep the stable of the of the wheel balancer voltage and frequency. NT:50Kg size:1129×1190×728mm (L*W*H) C、Requirement to the socket: Small size wheel balancer should be equipped with the power cord B、Air pressure conversion 1Mpa=l0Bar and the plug before out of the factory. The 1Bar=14.5Psi customer should directly equip the socket 1Bar≈1Kg/cm2...
using. *Dynamic wheel balancer must use the separate FIG 6 rated power source and connect with any other electrical equipment to the socket. If without the reliable earth power source, you must provide the reliable power source. * The input power cable must be firmly fixed. * If you have to move the wheel balancer, you must equip the protective device to avoid the *When the weight of the tire exceeds 15kg,you...
If the light of the workplace is bad, lighting equipment shall be ready by you. The ordinary fluorescent or incandescent lighting is better, it is no need too bright, the brightness not affecting any operation is appropriate 2.5) Parameter display/...
Page 14
Press to the option select item Enter self-calibration following FIG 9...
Suitable to the big tire assemble Mount the tire flange disk (fixed on the main Main shaft shaft ) Select the cone adapting to the center hole of the wheel cone quick tire and mount on the wheel balancer following the indication of the figure.
machine can also automatically start by the VALUE DISPLAY program setup. The minimum value of the standard weight is 5g DISPLAY UNBALANCE VALUE so if the weight you use is less than 5 g, the When the spin ends, the display will display the wheel balancer will not display the value and only displays the state of ―00‖.
When balance heavy-duty vehicles such as truck, please press and the truck balance mode light ALU2 Dis1=Dis+ ¾’’ Dis2=distance from 0 point to the outside of the When balance the car, please press and the flange disk-½’’ Dia1=Dia-1‖ car balance mode light Dia2=Dia-2 ½’...
Page 18
outside/inside tested and remove the unbalance when the wheel spin. Default condition( the indication lamps are not lightup) select the mode for car or for truck...
Static balance FIG 16 ALU Aluminum alloy rim balance mode ALU is the approximate weight summarized from the different sizes of the rim. See the introduction of the balance modes.(FIG 15). Press to enter in cycle and the static mode. ALU mode applies the clip of the weight according to the weight clip position in FIG15.You can also select the weight special scale to assist the completion of the weight clip.
Select a suitable tire with the small unbalance value and mount it on the main shaft and input the parameter of the rim correctly. Car mode and truck mode must be self-calibrated separately. Refer to the FIG9, press the key to enter the program of [ CAL]-[ CAL] and then press to enter the...
(7) Insert the vertical ( ┴) & horizontal ( ∥) sensor plugs according to the original position. (8) Calibrate the balancer again and install the upper cover and the side panel after check result is normal. (9)After change the computer board, phase sensor or the pressure sensor , it must self-calibrate.
Page 22
Description Cause Solution Start the machine but 1. Socket fault 1. Check the power supply circuit, 2.power board fault not display or the main plug and socket 3.The cable between the switch indicating lamp 2. Change the power board power board & main board not light 3.
WHEEL BALANCER ACCESSORY Standard accessory Accessory Name Quantity Accessory Name Quantity Cone/ flange 1 set 1 piece disk scale pliers 1 piece thread 1 piece shaft Quick nut 1piece weight 1piece Keep the working area clean. MAINTENANCE Never use the compressed air /water water spray to remove the dust and residual on the machine.
Make the calibration once per 6months. (established upon the rolling of the greases), LUBRICATION mm/10 spheres test, The only rotating parts of the wheel balancer are impression diam., ASTM the motor and the balancing shaft, so the bearing D 2266, mm these components must...
Page 25
Your help is crucial to reduce the amount of Electrical and electronic equipment must never natural resources used manufacturing be disposed of in the usual municipal waste but electrical and electronic equipment, minimize the use of landfill for product disposal and improve must be separately collected for their proper treatment.