Related Manuals for Nedap VP5001
Summary of Contents for Nedap VP5001
- Page 1 Instruction Manual InTouch, model VP5001 User Manual Version 03.000 / July 2022 / EN Original instructions Dairy Farming...
- Page 2 Copyright © Nedap N.V. All rights reserved. The information in this document is subject to change without notice, it is not to be reproduced in any way, in whole or in part, without the written consent of Nedap N.V. All trademarks referenced belong to their respective owners.
- Page 3 InTouch, model VP5001 InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN...
-
Page 4: Table Of Contents
Maintenance ..................13 Maintenance scheme ....................13 Troubleshooting .................. 14 Handling Instructions ................. 15 Glossary ..................... 16 Appendix .................... 17 InTouch menu overview ....................17 InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN... -
Page 5: Safety
General safety instructions Warning Always turn off the mains power supply when working on the electrical installation. Warning Always wear proper protection when installing and maintaining the Nedap VP5001. Caution Installation and service should only be done by locally qualified personnel. Caution Install the system according to the local rules and regulations. - Page 6 Make sure all cables are properly concealed, and form no danger for stumbling. Animal welfare and safety The automated actions of the Nedap Livestock Management systems do never discharge the installer and the user of the system from his/her responsibility to assure and to take care of the well-being of the animals.
-
Page 7: Intouch Overview
2.1 InTouch introduction The Nedap InTouch is used to control the milking process at each individual milking point of the whole parlor. The InTouch control unit is able to show real time milk yields for specific cows, measured by the SmartFlow milk meter. - Page 8 3. Milk cluster 9. Take off/Vacuum valve 4. Milk hose 10. Vacuum line for cleaning 5. Milk hose bracket 11. Vacuum valve 6. Milk line InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN...
-
Page 9: First Use
3 First use The first time the Nedap InTouch units are used after installation, the following tasks must be completed by the installer (in cooperation with the farmer): 1. Add animals to Velos using the Add animal option on the Farm or Quick entry window: a. -
Page 10: Operation
It is advised to keep the InTouch control panel as clean as possible to improve the usability of the control panel. InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN... - Page 11 LED is blinking or continuously on, this indicates that the milk cluster is down. When the Cluster LED is off, the milk cluster is up. InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN...
-
Page 12: Using The System
The Take off indicator is shown as three red dashes on the left side of the display. The Take off interval is set in Velos. InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN... - Page 13 The InTouchU display shows StArt. – 2. Press the Main button for a SHORT period again: – The attention light turns green. – The milking starts. InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN...
- Page 14 If the first group of cows has been milked and a cow in the next group is not identified, proceed as follows: 1. Go to the Nedap Parlor Monitor. 2. Correct the cow ID in the Cow information section (see the Parlor Monitor User Manual for more information).
-
Page 15: Maintenance
Regularly clean the outside of the InTouch with a soft cloth and a non-aggressive cleaning agent. The InTouch control panel must be cleaned at least once per two weeks. It is allowed to power wash the outside of the InTouch. InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN... -
Page 16: Troubleshooting
• Check the wiring. the SmartFlow is not received. • No animal identification. • It is still possible to operate the Main button. InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN... -
Page 17: Handling Instructions
In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive WEEE 2012/19/EU). InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN... -
Page 18: Glossary
VP8002 Velos Processing Unit (VPU) Velos Processing Unit (VP8002) VPU-online An online address for the herd manager that makes the Nedap system worldwide accessible by the Internet. Velos software Nedap software to control the system InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN... -
Page 19: Appendix
Enable pulsator 1 Enable pulsator 2 Testing active pulsator connection mode Display test. Enable all display segments and flash all LEDs InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN... - Page 20 Capacitive touch button value 1 Capacitive touch button value 2 Factory settings Set to 99 to restore factory defaults InTouch, model VP5001 / User Manual Dairy Farming Version 03.000 / July 2022 / EN...
- Page 21 ...
- Page 22 ...