Intermec EasyCoder PF8 Install Manual
Cutter
Hide thumbs
Also See for EasyCoder PF8:
- User manual (62 pages) ,
- Quick start manual (2 pages) ,
- Programmer's reference manual (180 pages)
Advertisement
Quick Links
Download this manual
See also:
User Manual
This PF8 Cutter Installation Instructions describes how to install a cutter
module in your PF8 printer. Your shipping contents include these items:
• One cutter module
• Two screws
• Two mounting brackets (one for the PF8d and another for the PF8t)
• These instructions
This kit must only be installed by an authorized service
technician. Intermec assumes no responsibility for personal
injury or damage if the installation is performed by an
unauthorized person.
Dieser Satz darf nur von einem autorisierten
Wartungstechniker installiert werden. Intermec übernimmt
keine Verantwortung für Verletzungen oder Sachschäden, falls
Warnung
die Installation von nicht autorisiertem Personal durchgeführt
wird.
The discharge of electrostatic energy accumulated on the
human body, clothing, or other surfaces can damage or
destroy the printhead or electronic components used in these
printers. Avoid touching the electrical connectors when
installing the cutter module.
Die Entladung von elektrostatischer Energie, die im
menschlichen Körper, in Kleidungsstücken oder auf anderen
Oberflächen gespeichert ist, kann den Druckkopf oder
elektronische Komponenten dieser Drucker beschädigen oder
zerstören. Vermeiden Sie, die Steckverbinder nicht berühren.
Cutter Installation Instructions
Advertisement
Related Manuals for Intermec EasyCoder PF8
Summary of Contents for Intermec EasyCoder PF8
- Page 1 • Two mounting brackets (one for the PF8d and another for the PF8t) • These instructions This kit must only be installed by an authorized service technician. Intermec assumes no responsibility for personal injury or damage if the installation is performed by an unauthorized person.
- Page 2 Spannungen führen. Immer das Netzkabel abziehen, bevor das Elektronikfach geöffnet wird. Warnung Disconnect power and place the printer on a flat surface. Open the top cover by pressing the cover open buttons on either side of the top cover. Remove the front cover piece.
- Page 3 Holding the mounting bracket in the slot, tip the printer up and tighten the screws to attach the mounting bracket to the printer. Push the cutter electrical connector through the cable access hole.
- Page 4 Put the cutter on the mounting bracket. Turn the printer over and tighten the screws to hold the cutter in place. Open the bottom case cover to access the main board of the printer. Note: You can use a coin or a screwdriver to open the bottom case...
- Page 5 Check the pin configuration of the socket before plugging in the connector. Close the bottom case cover. Your printer is now able to print on media for cut-off operation. Refer to the PF8d/PF8t User’s Guide (P/N 934-011-xxx) for instructions on loading media for cut-off operation.
- Page 6 Spannungen führen. Immer das Netzkabel abziehen, bevor das Elektronikfach geöffnet wird. Warnung Disconnect power and place the printer on a flat surface. Open the top cover by pressing the cover open buttons on either side of the top cover. Press the green locking buttons and open the ribbon rewind mechanism.
- Page 7 Plug the cutter connector into the cutter socket. Note: There are two sockets on the board, one is for the stripper and the other is for the cutter. Check the pin configuration of the socket before plugging in the connector. Put the cutter in the front cover space.
- Page 8 Hold the cutter module in place and tighten the screws. Your printer is now able to print on media for cut-off operation. Refer to the PF8d/PF8t User’s Guide for instructions on loading media for cut-off operation. Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A.