Setting Language - Insignia IS-TV040923 Owner's Manual

AUDIO/VIDEO JACK CONNECTIONS
4. To connect the TV to a VCR with an S-VIDEO Cable
Set the TV/AV selection for this connection, to AUX1.
If you connect a VCR with a S-VIDEO cable to the S-VIDEO IN jack on the rear of the TV, you must also connect the audio
cables to the AUDIO IN jacks on the rear of the TV. The S-VIDEO cable only carries the video signal. The audio signal is
separate.
VCR

SETTING LANGUAGE

This TV can display the on-screen language in English, Spanish or French.
On-screen language selection (step 3) will automatically appear on the screen when you press the MENU button initially.
Select the language you prefer first, then proceed with the other menu options.
1
Press the MENU button.
2
Press the SET + or – button to
select the "LANGUAGE" mode,
then press the ENTER button.
NOTE:
If Spanish or French is chosen, the Closed Caption indicators will be in the selected language, but the Closed Caption text
will not be affected by the language selection.
TV OPERATION
1 To turn on the TV, press the POWER button.
2
The VOLUME can be adjusted to a desired level by
pressing the VOL (VOLUME)
The sound level will be indicated on the TV screen by
green bars and a number. As the sound level in-
creases, so do the number of bars and the number on
the screen. The same is true for decreasing the level.
3
Set the TV/CATV menu option to the appropriate
position. When shipped from the factory, this menu
option is in the CABLE TV setting. See "TO MEMO-
RIZE CHANNELS".
TV - VHF/UHF channels
CATV - CABLE TV channels
4
CH (CHANNEL) and
Press and release the CH (CHANNEL)
The channel automatically stops at the next channel
set into memory. Press and hold the button down to
change channels more quickly.
For proper operation, before selecting channels,
they should be set into the TV's memory.
See "TO MEMORIZE CHANNELS".
3T11131A [E] P02-07
Rear of TV
AUDIO (L)
AUDIO (R)
(not supplied)
MENU
CH SETUP
PICTURE
STABLE SOUND ON OFF
LANGUAGE
V-CHIP SET
or button.
buttons
or button.
7
NOTE: When the S-video cable and the video cable
are connected to each jack at the same time,
the S-video cable takes precedence over the
video cable.
(not supplied)
3
Press the SET + or – button to
select the desired language:
English (ENGLISH), Spanish
(ESPAÑOL) or French
(FRANCAIS), then press the
ENTER button.
4 Press the MENU button until the menu screen is
cleared.
Direct Channel Selection buttons (0-9)
Press these buttons to select a channel. The channel
number will appear on the upper right corner of the TV
screen. If an invalid channel number is selected, the display
will revert to the original channel.
TV Mode Direct Channel Selection
When the TV/CATV menu option is in the TV position, all
channels can be instantly selected by using two buttons.
(For example, to select channel 2, press "0", then "2". If you
press only "2", channel selection will be delayed for a few
seconds). For channels 10 and above, press the 2 digits in
order.
CATV Mode Direct Channel Selection
When the TV/CATV menu option is in the CATV position,
channels can be selected as follows:
CH. 1-9 Press "0" twice, then 1-9 as needed.
Example, to select channel 2, press
"002".
CH. 10-12 Press "0", then remaining 2 digits.
Example, to select channel 12, press
"012".
CH. 13-99 Press the 2 digits in order.
Example, to select channel 36, press
"36".
CH. 100-125 Press the 3 digits in order.
Example, to select channel 120, press
"120".
NOTE: If the station being viewed stops broadcasting, the
TV will automatically shut off after 15 minutes.
2/24/05, 2:47 PM
(CONTINUED)
7