Hoshizaki DCM-500BAH Instruction Manual
Cubelet icemaker / dispenser
Hide thumbs
Also See for DCM-500BAH:
- Service manual (69 pages) ,
- Parts list (46 pages) ,
- Instruction manual (32 pages)
Related Manuals for Hoshizaki DCM-500BAH
Summary of Contents for Hoshizaki DCM-500BAH
- Page 1 Hoshizaki Hoshizaki America, Inc. Cubelet Icemaker / Dispenser Models DCM-500BAH DCM-500BAH-OS DCM-500BWH DCM-500BWH-OS INSTRUCTION MANUAL “A Superior Degree of Reliability” www.hoshizaki.com ® Issued: 3-13-2008...
- Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write, or send an e-mail message to the HOSHIZAKI Technical Support Department for assistance. HOSHIZAKI AMERICA, INC.
-
Page 3: Table Of Contents
Please retain this booklet for any further reference that may be necessary. I. Specifications ... 4 A. Nameplate Rating ... 4 1. DCM-500BAH (air-cooled) ... 4 . DCM-500BAH-OS (air-cooled) ... 5 3. DCM-500BWH (water-cooled) ... 6 4. DCM-500BWH-OS (water-cooled) ... 7 B. -
Page 4: Specifications
I. Specifications A. Nameplate Rating 1. DCM-500BAH (air-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE COMPRESSOR GEAR MOTOR FAN MOTOR AGITATING MOTOR DISPENSING MOTOR OTHER MAXIMUM FUSE SIZE MAX. HACR BREAKER (USA ONLY) MAX. CIRC. BREAKER (CANADA ONLY) -
Page 5: Dcm-500Bah-Os (Air-Cooled)
2. DCM-500BAH-OS (air-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE COMPRESSOR GEAR MOTOR FAN MOTOR AGITATING MOTOR DISPENSING MOTOR OTHER MAXIMUM FUSE SIZE MAX. HACR BREAKER (USA ONLY) MAX. CIRC. BREAKER (CANADA ONLY) MINIMUM CIRCUIT AMPACITY DESIGN PRESSURE... -
Page 6: Dcm-500Bwh (Water-Cooled)
3. DCM-500BWH (water-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE COMPRESSOR GEAR MOTOR FAN MOTOR AGITATING MOTOR DISPENSING MOTOR OTHER MAXIMUM FUSE SIZE MAX. HACR BREAKER (USA ONLY) MAX. CIRC. BREAKER (CANADA ONLY) MINIMUM CIRCUIT AMPACITY DESIGN PRESSURE... -
Page 7: Dcm-500Bwh-Os (Water-Cooled)
4. DCM-500BWH-OS (water-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE COMPRESSOR GEAR MOTOR FAN MOTOR AGITATING MOTOR DISPENSING MOTOR OTHER MAXIMUM FUSE SIZE MAX. HACR BREAKER (USA ONLY) MAX. CIRC. BREAKER (CANADA ONLY) MINIMUM CIRCUIT AMPACITY DESIGN PRESSURE... -
Page 8: Dimensions/Connections
B. Dimensions/Connections 1. DCM-500BAH... -
Page 9: Dcm-500Bah-Os
2. DCM-500BAH-OS... -
Page 10: Dcm-500Bwh
3. DCM-500BWH... -
Page 11: Dcm-500Bwh-Os
4. DCM-500BWH-OS... - Page 12 5. DCM-500BAH(-OS) or DCM-500BWH(-OS) on optional SD-450 or SD-500 Stand Unit: inch (mm) SD-450 6-1/4" (667) -1/8" (56) 1-7/16" (37) SD-500 5-7/8" (658)
-
Page 13: Installation And Operating Instructions
7) This icemaker can be installed on a countertop or optional stand. If using an optional stand, the recommended stands are HOSHIZAKI STAND SD-450 or SD-500. B. How to Remove Panels See Fig. 1 •... -
Page 14: Location
C. Location 1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F (7°C to 38°C); Normal operating water temperature should be within +45°F to +90°F (7°C to 3°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect icemaker performance. -
Page 15: Electrical Connection
E. Electrical Connection 1. Electrical connections must be made in accordance with the instructions on the "WARNING" tag, provided with the pig tail leads in the junction box. . Electrical connections must meet national, state, and local electrical code requirements. Failure to meet these code requirements could cause severe injury to individuals or extensive damage to equipment. -
Page 16: Water Supply And Drain Connections
• A plumbing permit and services of a licensed plumber may be required in some areas. • External filters, strainers, or softeners may be required depending on the water quality. Contact your local Hoshizaki distributor for recommendations. • Water supply inlet is 1/" female pipe thread (FPT). - Page 17 DCM-500BAH(-OS) Drip Tray Drain Outlet 3/4" FPT Bin Drain Outlet 3/4" FPT DCM-500BWH(-OS) Condenser Drain Outlet 3/8" FPT Condenser Water Supply Inlet 1/2" FPT Drip Tray Drain Outlet 3/4" FPT Bin Drain Outlet 3/4" FPT Separate piping to approved drain.
-
Page 18: Final Checklist
G. Final Checklist 1) Is the icemaker level? ) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°C to +38°C) and the water temperature within +45°F to +90°F (+7°C to +3°C) all year around? 3) Is there at least 6"... -
Page 19: Startup
H. Startup 1. All parts are factory-adjusted. Improper adjustments may result in failure. . If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 1) Open the water supply line shut-off valve. ) Remove the front panel. -
Page 20: Controls And Adjustments
The figures on the label indicate dispensing time (sec.). See Fig. 5. When shipped, the portion control is set at the minimum dispensing time (0.6 sec.). DCM-500BAH(-OS); DCM-500BWH(-OS) ... . Approximately 0.7 oz./0.6 sec. Approximate amount of ice dispensed per second. -
Page 21: Cleaning And Maintenance
A. Cleaning and Sanitizing Instructions HOSHIZAKI recommends cleaning this unit at least twice a year. More frequent cleaning, however, may be required in some existing water conditions. 1. To prevent injury to individuals, do not use any ammonia type cleaners. -
Page 22: Water System
1. Water System a) Cleaning Solution Dilute 9.6 fl. oz. (0.9 l) of recommended cleaner, Hoshizaki "Scale Away" or "LIME-A- WAY" (Economics Laboratory, Inc.), with 1.6 gal. (6.0 l) of warm water. b) Cleaning Procedure 1) Close the water supply line shut-off valve. - Page 23 Perform after cleaning and sanitizing the water system as outlined above. a) Cleaning Solution Dilute 9.6 fl. oz. (0.9 l) of recommended cleaner, Hoshizaki "Scale Away" or "LIME-A- WAY" (Economics Laboratory, Inc.), with 1.6 gal. (6.0 l) of warm water.
- Page 24 3) Remove the front cover of the storage bin. 4) Remove the motor bracket thumbscrews, first from the vertical plane and then from the horizontal plane. While holding on to the corresponding agitator or auger, move the agitating motor or the dispensing motor towards you. Remove the agitator and the dispensing auger from the storage bin.
-
Page 25: Maintenance
Consult with your local distributor about inspection and maintenance service. To obtain the name and phone number of your local distributor, visit www.hoshizaki.com or call Hoshizaki Technical Support at 1-800-33-1940 in the USA. 1. Only qualified service technicians should attempt to service or maintain this icemaker. -
Page 26: Preparing The Icemaker For Long Storage
C. Preparing the Icemaker for Long Storage When the icemaker is not used for two or three days under normal conditions, it is sufficient to only move the control switch to the "OFF" position. When storing the icemaker for extended time or in sub-freezing temperatures, turn the water off and drain out all water from the water lines and remove the ice from the storage bin. - Page 27 3) Attach a compressed air or carbon dioxide supply to the condenser water supply line drain valve. 4) Open the water regulating valve by using a screwdriver to pry up on the spring retainer underneath the spring. While holding the valve open, blow out the condenser using the compressed air or carbon dioxide supply until water stops coming out.
- Page 28 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A2EE10A...