Page 1
Reliability is a beautiful thing CUBELET ICE DISPENSER INSTRUCTION MANUAL DCM-500BAF DCM-500BWF DCM-750BAF DCM-750BWF ISSUED: REVISED: NOV. 18, 2003 APRIL 13, 1998...
Page 2
HOSHIZAKI provides this manual primarily to assist qualified service technicians in the installation, maintenance and service of the ice dispenser. Should the reader have any questions or concerns which have not been satisfactorily addressed, please call or write to the HOSHIZAKI Technical Support Department for assistance.
[b] DCM-500BWF (Water-cooled) [b] DCM-500BWF (Water-cooled) [b] DCM-500BWF (Water-cooled) [b] DCM-500BWF (Water-cooled) [b] DCM-500BWF (Water-cooled) MODEL NUMBER MODEL NUMBER MODEL NUMBER MODEL NUMBER MODEL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE...
[c] DCM-750BAF (Air-cooled) [c] DCM-750BAF (Air-cooled) [c] DCM-750BAF (Air-cooled) [c] DCM-750BAF (Air-cooled) [c] DCM-750BAF (Air-cooled) MODEL NUMBER MODEL NUMBER MODEL NUMBER MODEL NUMBER MODEL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE...
[d] DCM-750BWF (Water-cooled) [d] DCM-750BWF (Water-cooled) [d] DCM-750BWF (Water-cooled) [d] DCM-750BWF (Water-cooled) [d] DCM-750BWF (Water-cooled) MODEL NUMBER MODEL NUMBER MODEL NUMBER MODEL NUMBER MODEL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE AC SUPPLY VOLTAGE...
II. GENERAL INFORMATION 1. CONSTRUCTION 1. CONSTRUCTION 1. CONSTRUCTION 1. CONSTRUCTION 1. CONSTRUCTION Hoshizaki Cubelet Ice Dispensers, models DCM-500BAF, DCM-500BWF, DCM-750BAF and DCM-750BWF include Water Supply, Freezer, Condensing, Storage, Dispensing and Control Assemblies. Fig. 1 Fig. 1 Fig. 1 Fig. 1...
2. OPERATION - How it works 2. OPERATION - How it works 2. OPERATION - How it works 2. OPERATION - How it works 2. OPERATION - How it works Water flows from a potable water source through the Water Supply Line Shut-off Valve, enters at the water inlet fitting and on to the Water Supply Assembly.
Nameplate. 6) Check that a spare fuse is provided as an accessory. For DCM-500BAF and DCM-500BWF, 1 A and 0.5 A fuses, and for DCM-750BAF and DCM-750BWF, 3 A and 0.5 A fuses are located on the Control Box.
3. LOCATION 3. LOCATION 3. LOCATION 3. LOCATION 3. LOCATION This ice dispenser is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F; normal operating water temperature should be within +45°C to +90°C. Operation of the ice dispenser, for extended periods, outside of these normal temperature ranges may affect production capacity.
3) Remove the Front Panel by lifting up and pulling toward you. 4) Place the ice dispenser on the Cabinet Stand. Combination: SD-450 ..DCM-500BAF, BWF SD-700 ..DCM-750BAF, BWF 5) You must secure the ice dispenser to the Cabinet Stand with four bolts (Cabinet Stand accessory).
Page 17
DIMENSIONS WITH DCM-500BAF ON SD-450 Unit: inch (mm.) Fig. 4 Fig. 4 Fig. 4 Fig. 4 Fig. 4...
Page 18
DIMENSIONS WITH DCM-750BAF ON SD-700 Unit: inch (mm.) Fig. 5 Fig. 5 Fig. 5 Fig. 5 Fig. 5...
6. ELECTRICAL CONNECTION - See Fig. 6 6. ELECTRICAL CONNECTION - See Fig. 6 6. ELECTRICAL CONNECTION - See Fig. 6 6. ELECTRICAL CONNECTION - See Fig. 6 6. ELECTRICAL CONNECTION - See Fig. 6 This ice dispenser requires a ground that meets the national and local electrical code requirements.
7. WATER SUPPLY AND DRAIN CONNECTIONS - See Fig. 7 and 8 7. WATER SUPPLY AND DRAIN CONNECTIONS - See Fig. 7 and 8 7. WATER SUPPLY AND DRAIN CONNECTIONS - See Fig. 7 and 8 7. WATER SUPPLY AND DRAIN CONNECTIONS - See Fig. 7 and 8 7.
Page 21
Fig. 7 Fig. 7 Fig. 7 Fig. 7 Fig. 7 Air Cooled Model Fig. 8 Fig. 8 Fig. 8 Fig. 8 Fig. 8 Water Cooled Model...
8. FINAL CHECK LIST 8. FINAL CHECK LIST 8. FINAL CHECK LIST 8. FINAL CHECK LIST 8. FINAL CHECK LIST 1) Is the ice dispenser level? 2) Is the ice dispenser in a site where the ambient temperature is within +45°F to +100°F all year around? 3) Is there at least a 6"...
9. START UP - See Fig. 9 9. START UP - See Fig. 9 9. START UP - See Fig. 9 1. All parts are factory-adjusted. Improper adjustments may result in failure. 2. If the unit is turned off, wait for at least 3 minutes before restarting the ice dispenser to prevent damage to the Compressor.
Page 24
Motor(s) after 30 minutes of running. 12) Move the Dispense Mode Switch, located at the bottom of the Middle Front Panel, to the “PORTION” or “CONTINUOUS” position. 13) Press the Push Button to dispense ice, and the dispensing mechanism will operate. 14) Press the Push Button to dispense water, and the Water Valve will open.
11. PREPARING THE ICEMAKER FOR LONG STORAGE - See Fig. 11 11. PREPARING THE ICEMAKER FOR LONG STORAGE - See Fig. 11 11. PREPARING THE ICEMAKER FOR LONG STORAGE - See Fig. 11 11. PREPARING THE ICEMAKER FOR LONG STORAGE - See Fig. 11 11.
Page 27
Before operating the dispenser next time, check that the Water Supply Line Drain Valve is closed, and open the Water Supply Line Shut-off Valve. Note: When shutting off the ice dispenser at sub-freezing temperatures, run the ice dispenser with the Water Supply Line Shut-off Valve closed, and blow out the water inlet line, by using air pressure.
1) Close the Water Supply Line Shut-off Valve. 2) Dilute approximately 9.6 fl. oz. of recommended cleaner, Hoshizaki "Scale Away" or “Lime-Away” (Economics Laboratory, Inc.) with 1.6 gal of water.
Page 29
8) Wait for 10 minutes before starting the icemaking process. Then turn on the Power Switch and move the Control Switch to the “ICE” position. Run the ice dispenser until it stops automatically. Note: This ice dispenser will not run without the Front Panel. Replace the Top Panel and the Front Panel.
Then remove the Agitator(s) and the Dispensing Auger. See Fig. 13. Note: Models DCM-750BAF and BWF are provided with two Agitators, and models DCM-500BAF and BWF with one Agitator. 3) Remove the Bin Control Bracket Assembly. See Fig. 14 4) Remove the Snap Pin, the Shaft and the Activator.
Page 31
6. Remove the Spout Cover and, the black Ice Dispensing Spout and the Water Dispensing Nozzle. See Fig. 16. 7) Immerse the parts removed in the above steps 2) through 6) in the cleaning and sanitizing solution for about 15 minutes each. 8) Rinse these parts thoroughly with clean water.
Consult with your local distributor about inspection and maintenance service. To obtain the name and phone number of your local distributor, call Hoshizaki Technical Support at 1-800-233-1940. 1) Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean, soft cloth.
Page 33
3) Air Filter (Air-cooled model only) - See Fig. 17. A plastic mesh air filter removes dirt or dust from the air and keeps the Condenser from getting clogged. As the filter becomes clogged, the ice dispenser’s performance will be reduced.
Page 34
HOSHIZAKI HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH PEACHTREE CITY, GA 30269...