Table of Contents
Advertisement
Available languages
Available languages
English
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Removing, Changing and/or Replacing the
Cutting Dies (Fig. E)
WARNING: Never attempt to repair a damaged
or worn cutting die. This could weaken the die and
result in a serious injury. Discard the entire set and
replace with a new set.
The tool is equipped with a stationary cutting die
moveable cutting die
4
. Cutting die orientation is critical
when changing or replacing the cutting dies.
1. Loosen both cutting die cap screws
counterclockwise using the hex wrench provided.
nOTE: Always replace both cutting dies and screws.
Cutting edges on the inside sliding against each other.
Laser marked arrows indicate the cutting edge.
8
3
and a
11
2. Tighten cutting die cap screws
hex wrench.
3. Install a battery and cycle the tool to ensure proper
assembly and alignment prior to making a cut.
CAUTION: If the cutting die cap screws or hex wrench
are lost or damaged replace with identical replacement
parts. Recommended replacement parts for use with
your tool are available at extra cost from your local
dealer or authorized service center. Always use identical
replacement parts
Installing and Removing the Battery Pack
(Fig. D)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
and firmly pull the battery pack out of the tool
6
handle. Insert it into the charger as described in the charger
section of this manual.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Proper Hand Position (Fig. G)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
12
.
Belt Hook (Fig. F)
Included with Some Models
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the belt hook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing a belt hook, use
only the screw that is provided. Be sure to securely tighten
the screw.
A belt hook
can be be attached to either side of the tool
9
using only the screw
10
11
clockwise using the
5
into the tool handle, align the
provided, to accommodate left- or
Advertisement
Table of Contents
