Makita DC10SB Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Drill
  5. DC10SB
  6. Instruction manual

Makita DC10SB Instruction Manual

Cordless led flashlight, cordless impact wrench
Hide thumbs Also See for DC10SB:
Table of Contents

Advertisement

Quick Links

Symbols
The followings show the symbols used for the equipment. Be sure that you understand their meaning before use.
• Indoor use only.
• DOUBLE INSULATION
• Charging.
• Delay charge (Battery cooling, or
too cold battery).
• Delay charge (Too hot or too cold
battery).
• Do not short battery.
• Do not expose battery to water or
rain.
Specification:
Model
DC10SB
Input
Output
D.C. 10.8 V – D.C. 12 V (max.)
Weight
0.63 kg (1.5 lbs)
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
SAVE THESE
1.
INSTRUCTIONS
– This manual contains important safety and
operating instructions for battery charger.
2.
Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3.
CAUTION – To reduce risk of injury, charge only
Makita type rechargeable batteries. Other types
of batteries may burst causing personal injury and
damage.
4.
Non-rechargeable batteries cannot be charged with
this battery charger.
5.
Use a power source with the voltage specified on the
nameplate of the charger.
6.
Do not charge the battery cartridge in presence of
flammable liquids or gases.
7.
Do not expose charger to rain or snow.
8.
Never carry charger by cord or yank it to disconnect
from receptacle.
9.
After charging or before attempting any maintenance
or cleaning, unplug the charger from the power
source. Pull by plug rather than cord whenever
disconnecting charger.
DC10WD
A.C. 120 V 50 – 60 HZ
0.35 kg (0.77 lbs)
• Read instruction manual.
• Ready to charge.
• Charging complete.
• Defective battery.
• Cooling abnormality.
• Do not destroy battery by fire.
• Always recycle battery.
10. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
11. Do not operate charger with damaged cord or plug. If
the cord or plug is damaged, ask Makita authorized
service center to replace it in order to avoid a hazard.
12. Do not operate or disassemble charger if it has
received a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualified
serviceman. Incorrect use or reassembly may result
in a risk of electric shock or fire.
13. The battery charger is not intended for use by young
children or infirm persons without supervision.
14. Young children should be supervised to ensure that
they do not play with the battery charger.
15. Do not charge battery cartridge when room
temperature is BELOW 10°C (50°F) or ABOVE 40°C
(104°F). At the cold temperature, charging may not
start.
16. Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
17. Do not allow anything to cover or clog the charger
vents.
IMPORTANT: Read Before Using.
DC10SB
DC10WD

Advertisement

Table of Contents
loading

Related Manuals for Makita DC10SB

Summary of Contents for Makita DC10SB

  • Page 1 11. Do not operate charger with damaged cord or plug. If the cord or plug is damaged, ask Makita authorized – This manual contains important safety and service center to replace it in order to avoid a hazard.
  • Page 2 BL1021B cartridge BL1041B NOTE: • The battery charger is for charging Makita-battery When the battery cartridge is too hot, charging does not begin until the battery cartridge temperature reaches cartridge. Never use it for other purposes or for other manufacturer’s batteries.
  • Page 3 • Follow the steps instructed in this manual, and complete – One more screw (only for DC10SB) (4mm (5/32”) x the whole procedures at once. The charger may fall and more than 40mm (1-9/16”)) - for supporting the cause injury or damage if you stop the work in the half charger.
  • Page 4 (DC10SB) 30mm 69mm 90mm ≧ ≧ (1-3/16”) (2-23/32”) (3-9/16”) 30mm ≧ (1-3/16”) 32mm 50mm ≧ ≧ (1-9/32”) (1-31/32”) 180mm ≧ 110mm (7-3/32”) 75mm ≧ (4-11/32”) (2-31/32”) ≈8mm (5/16”) 115mm ≧ (4-17/32”) (DC10WD) 55mm 115mm ≧ ≧ (2-3/16”) (4-17/32”) 35mm ≧...
  • Page 5 INSTRUCTION MANUAL Cordless Driver Drill FD05 FD06 Read Before Using. IMPORTANT:...

  • Page 6: Specifications

    SPECIFICATIONS Model: FD05 FD06 Drilling capacities Steel 10 mm (3/8") Wood 21 mm (13/16") Fastening Wood screw 5.1 mm x 63 mm (7/32" x 2-1/2") capacities Machine screw M6 (1/4") No load speed High (2) 0 - 1,700 /min (RPM) Low (1) 0 - 450 /min Overall length...

  • Page 7: Cordless Driver Drill Safety Warnings

    parts. This will ensure that the safety of the power jewellery or long hair can be caught in moving parts. tool is maintained. If devices are provided for the connection of Follow instruction for lubricating and chang- ing accessories. dust extraction and collection facilities, ensure these are connected and properly used. Use of Keep handles dry, clean and free from oil and dust collection can reduce dust-related hazards.

  • Page 8: Functional Description

    If you can see the red indicator on the causing fires, personal injury and damage. It will upper side of the button, it is not locked completely. also void the Makita warranty for the Makita tool and charger. CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen.

  • Page 9: Switch Action

    Electric brake This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after the switch trigger is released, have the tool serviced at a Makita service center. Lighting up the front lamp 1. Indicator lamps 2.

  • Page 10: Reversing Switch Action

    Reversing switch action Speed change 1. Speed change lever 1. Reversing switch lever CAUTION: Always set the speed change lever fully to the correct position. If you operate the tool with CAUTION: Always check the direction of the speed change lever positioned halfway between the rotation before operation.

  • Page 11: Installing Hook

    Graduation Machine screw Wood Soft wood – ɸ3.5 x 22 ɸ4.1x 38 screw (e.g. pine) Hard wood – ɸ3.5 x 22 – (e.g. lauan) – ɸ4.1x 38 ASSEMBLY CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

  • Page 12: Screwdriving Operation

    Installing driver bit holder Screwdriving operation Optional accessory CAUTION: Adjust the adjusting ring to the proper torque level for your work. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or driver bit may be damaged. Place the point of the driver bit in the screw head and apply pressure to the tool.

  • Page 13: Using Holster

    Thread a waist belt or similar through holster alcohol or the like. Discoloration, deformation or holder. cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool 1.
  • Page 14 Driver bit holder • Holster • Plastic carrying case • Hook • Makita genuine battery and charger NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
  • Page 15 < USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: •...
  • Page 16 Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita luminaire and charger. Tips for maintaining maximum battery life 1.
  • Page 17 INSTRUCTION MANUAL Cordless Impact Wrench WT02 IMPORTANT: Read Before Using.
  • Page 18 EPTA-Procedure 01/2014, are shown in the table. Applicable battery cartridge and charger Battery cartridge BL1016 / BL1021B / BL1041B Charger DC10SB / DC10WD • Some of the battery cartridges and chargers listed above may not be available depending on your region of residence. WARNING: Only use the battery cartridges and chargers listed above.
  • Page 19 Power tools can produce electromagnetic fields Store idle power tools out of the reach of chil- (EMF) that are not harmful to the user. However, dren and do not allow persons unfamiliar with users of pacemakers and other similar medical the power tool or these instructions to operate devices should contact the maker of their device and/ the power tool.
  • Page 20 Only use genuine Makita batteries. number of blow Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
  • Page 21 Tips for maintaining maximum Indicating the remaining battery battery life capacity Charge the battery cartridge before completely dis- Only for battery cartridges with the indicator charged. Always stop tool operation and charge the battery cartridge when you notice less tool power. Never recharge a fully charged battery cartridge.
  • Page 22 Depress the reversing switch lever from the is released, have the tool serviced at a Makita service A side for clockwise rotation or from the B side for coun- center.
  • Page 23 Installing or removing impact socket OPERATION CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red indicator on the upper side of the button, it is not locked completely. Insert it fully until the red indicator cannot be seen.
  • Page 24 (70) M10 (3/8″) To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should (60) be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. M10 (3/8″) (40) M8 (5/16″) OPTIONAL (30) M8 (5/16″)
  • Page 25 < USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: •...

This manual is also suitable for:

Dc10wdCt323Fd05Fd06Ml103Wt02

Table of Contents