Page 4
Copyright This document and parts thereof must not be reproduced or copied without written permission from ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose. The software or hardware described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such license.
Page 5
In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other than under explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or damage resulting from the use of this manual or the application of the equipment.
Page 6
(EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB in accordance with the product standards EN 50263 and EN 60255-26 for the EMC directive, and with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive.
Table of contents Table of contents Section 1 Introduction...............7 This manual..................7 Intended audience................7 Product documentation...............7 Product documentation set............7 Document revision history.............8 Related documentation..............8 Symbols and conventions..............8 Symbols..................8 Document conventions..............9 Functions, codes and symbols............10 Section 2 IEC 60870-5-103 data mappings........15 Overview...................15 Supported functions................15 Indications and controls..............18 General Data(FUN=0) IEC 60870-5-103 standard......18...
Page 8
Table of contents LD0.MAPGAPC2 Multipurpose analog protection function (2)....................27 LD0.MAPGAPC3 Multipurpose analog protection function (3)....................27 LD0.MAPGAPC4 Multipurpose analog protection function (4)....................28 LD0.MAPGAPC5 Multipurpose analog protection function (5)....................28 LD0.MAPGAPC6 Multipurpose analog protection function (6)....................28 LD0.MAPGAPC7 Multipurpose analog protection function (7)....................28 LD0.MAPGAPC8 Multipurpose analog protection function (8)....................29 LD0.MAPGAPC9 Multipurpose analog protection function (9)....................29...
Page 10
1:1 LED state)................49 LD0.FKEYGGIO1 LHMI LED indications........50 LD0.SECRSYN1 Synchrocheck indications .......50 Class 2 data measurands..............51 Class 2 private measurand data (6 and 7)........52 Section 3 Interoperability profile for 620 series IEC 60870-5-103..............55 Physical layer...................55 Electrical interface...............55 Optical interface................55 Transmission speed..............55 Link layer..................55...
Page 11
Table of contents Earth fault indications in monitor direction......57 Fault indications in monitor direction........57 Auto-reclosure indications in monitor direction.......58 Measurands in monitor direction..........59 Generic functions in monitor direction........59 Selection of standard information numbers in control direction..................59 System functions in control direction........59 Generic functions in monitor direction........59 Basic application functions............60 Miscellaneous................60...
Section 1 1MRS757657 A Introduction Section 1 Introduction This manual The point list manual describes the outlook and properties of the data points specific to the IED. The manual should be used in conjunction with the corresponding communication protocol manual. Intended audience This manual addresses the communication system engineer or system integrator responsible for pre-engineering and engineering for communication setup in a...
1.3.2 Document revision history Document revision/date Product version History A/2013-05-07 First release Download the latest documents from the ABB Website http://www.abb.com/substationautomation. 1.3.3 Related documentation Name of the document Document ID IEC 60870-5-103 Communication Protocol Manual 1MRS757647 Symbols and conventions 1.4.1...
Section 1 1MRS757657 A Introduction of a hazard which could result in corruption of software or damage to equipment or property. The information icon alerts the reader of important facts and conditions. The tip icon indicates advice on, for example, how to design your project or how to use a certain function.
Page 18
Section 1 1MRS757657 A Introduction Function IEC 61850 IEC 60617 IEC-ANSI Multipurpose analog protection, MAPGAPC7 MAP (7) MAP (7) instance 7 Multipurpose analog protection, MAPGAPC8 MAP (8) MAP (8) instance 8 Multipurpose analog protection, MAPGAPC9 MAP (9) MAP (9) instance 9 Multipurpose analog protection, MAPGAPC10 MAP (10)
Page 19
Section 1 1MRS757657 A Introduction Function IEC 61850 IEC 60617 IEC-ANSI Runtime counter for machines and MDSOPT1 OPTS (1) OPTM (1) devices, instance 1 Runtime counter for machines and MDSOPT2 OPTS (2) OPTM (2) devices, instance 2 Measurement Three-phase current measurement, CMMXU1 3I (1) 3I (1)
Page 20
Section 1 1MRS757657 A Introduction Function IEC 61850 IEC 60617 IEC-ANSI Time delay on (8 pcs), instance 4 TONGAPC4 TON (4) TON (4) Set reset (8 pcs), instance 1 SRGAPC1 SR (1) SR (1) Set reset (8 pcs), instance 2 SRGAPC2 SR (2) SR (2)
Section 2 1MRS757657 A IEC 60870-5-103 data mappings Section 2 IEC 60870-5-103 data mappings Overview This document describes the IEC 60870-5-103 data points and structures available in the IED. The point lists describe a superset of all data available through the standard configuration/s.
Section 2 1MRS757657 A IEC 60870-5-103 data mappings Indications and controls Table 3: Explanations of the indications and controls table columns Column name Description IEC 61850 Original IED data object identification. Described in the IEC 61850 format as name Logical Device.Logical Node and thereafter .Data Object.Data Attribute. Logical Node is the same as the application function block name.
Section 2 1MRS757657 A IEC 60870-5-103 data mappings IEC 61850 name SA name Description DPI value ASDU .Q4.stVal Input 4 signal 10=On .Q5.stVal Input 5 signal 10=On .Q6.stVal Input 6 signal 10=On .Q7.stVal Input 7 signal 10=On .Q8.stVal Input 8 signal 10=On 2.3.4 LD0.MVGAPC2 Multipurpose binary inputs (2)
Section 2 1MRS757657 A IEC 60870-5-103 data mappings IEC 61850 name SA name Description DPI value ASDU .Rs6.ctlVal Reset flip-flop 6 10=Reset .Rs7.ctlVal Reset flip-flop 7 10=Reset .Rs8.ctlVal Reset flip-flop 8 10=Reset 2.3.9 LD0.SPCGGIO1 Multipurpose binary outputs (1) The binary outputs can be configured either as pulse- or persistent-type outputs. Pulse- type outputs are triggered with the write value "ON".
Section 2 1MRS757657 A IEC 60870-5-103 data mappings Table 13: LD0.SPCGGIO2 Multipurpose binary outputs (2) IEC 61850 name SA name Description DPI value ASDU LD0.SPCGGIO2 .SPCS01.ctlVal Output control 1 10/01=On/Off 1,20 .SPCS02.ctlVal Output control 2 10/01=On/Off 1,20 .SPCS03.ctlVal Output control 3 10/01=On/Off 1,20 .SPCS04.ctlVal...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings IEC 61850 name SA name Description DPI value ASDU .SPCS12.ctlVal Output control 12 10/01=On/Off 1,20 .SPCS13.ctlVal Output control 13 10/01=On/Off 1,20 .SPCS14.ctlVal Output control 14 10/01=On/Off 1,20 .SPCS15.ctlVal Output control 15 10/01=On/Off 1,20 .SPCS16.ctlVal Output control 16...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings 2.3.24 LD0.MAPGAPC4 Multipurpose analog protection function Table 27: LD0.MAPGAPC4 Multipurpose analog protection function (4) IEC 61850 name SA name Description DPI value ASDU LD0.MAPGAPC4 .Str.general START Stage Start 10=Start .Op.general OPERATE Stage Operate 10=Operate 2.3.25 LD0.MAPGAPC5 Multipurpose analog protection function...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings 2.3.28 LD0.MAPGAPC8 Multipurpose analog protection function Table 31: LD0.MAPGAPC8 Multipurpose analog protection function (8) IEC 61850 name SA name Description DPI value ASDU LD0.MAPGAPC8 .Str.general START Stage Start 10=Start .Op.general OPERATE Stage Operate 10=Operate 2.3.29 LD0.MAPGAPC9 Multipurpose analog protection function...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings 2.3.32 LD0.MAPGAPC12 Multipurpose analog protection function (12) Table 35: LD0.MAPGAPC12 Multipurpose analog protection function (12) IEC 61850 name SA name Description DPI value ASDU LD0.MAPGAPC12 .Str.general START Stage Start 10=Start .Op.general OPERATE Stage Operate 10=Operate 2.3.33...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings 2.3.72 LD0.EFHPTOC1 Non-directional earth-fault and sensitive earth-fault protection - high stage 1 Table 75: LD0.EFHPTOC1 Non-directional earth-fault and sensitive earth-fault protection - high stage 1 IEC 61850 name SA name Description DPI value ASDU LD0.EFHPTOC1 High stage...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings 2.3.76 LD0.DEFHPDEF1 Directional earth-fault protection - high stage 1 Table 79: LD0.DEFHPDEF1 Directional earth-fault protection - high stage 1 IEC 61850 name SA name Description DPI value ASDU LD0.DEFHPTOC1 High (1) stage .Str.general START -start...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings 2.3.80 LD0.VMMXU1 Phase voltage (1) limit supervision Table 83: LD0.VMMXU1 Phase voltage (1) limit supervision IEC 61850 name SA name Description DPI value ASDU LD0.VMMXU1 .HiAlm.stVal HIGH_ALARM High alarm 10=Alarm .HiWrn.stVal HIGH_WARN High warning 10=Warning .LoWrn.stVal...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings IEC 61850 name SA name Description DPI value ASDU .ClsAlm.stVal TRV_T_CL_ALM Cls travel time alarm 10=Alarm .SprChaAlm.stVal SPR_CHR_ALM Spring charge time alarm 10=Alarm .OpNumAlm.stVal OPR_ALM CB operations alarm 10=Alarm .OpNumLO.stVal OPR_LO CB operations lockout 10=Lockout .LonTmAlm.stVal MON_ALM...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings IEC 61850 name SA name Description DPI value ASDU .ItlByPss.stVal ITL_BYPASS Interlocking bypass 10=Bypassed CTRL.DCXSWI1 .BlkOpn.stVal BLK_OPEN Open blocked 10=Blocked .BlkCls.stVal BLK_CLOSE Close blocked 10=Blocked CTRL.DCCSWI1 .stSeld.stVal SELECTED DC selected 10=Selected .Pos.stVal/ctlVal POSITION DC pos/control 10/01=Close/Open...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings IEC 61850 name SA name Description DPI value ASDU 00/01/11=LED .ISCSO7.stVal LED 7 state State 00/01/11=LED .ISCSO8.stVal LED 8 state State 00/01/11=LED .ISCSO9.stVal LED 9 state State 00/01/11=LED .ISCSO10.stVal LED 10 state State 00/01/11=LED .ISCSO11.stVal...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings Class 2 data measurands Class 2 data measurands use ASDU type 9, function type 10 and information number 236 for frame 6 and 237 for frame 7. Start Length Length Start Cntrl Addr Link user data Csum...
Section 2 1MRS757657 A IEC 60870-5-103 data mappings 2.4.1 Class 2 private measurand data (6 and 7) Class2 frames 6 and 7 are identical in this IED. Table 107: Class 2 private measurand data (6 and 7) IEC 61850 name Description Scale LD0.CMMXU1 Phase currents (1)
Page 59
Section 2 1MRS757657 A IEC 60870-5-103 data mappings IEC 61850 name Description Scale LD0.VSMSQI1 Sequence of voltages (1) LD0.VSMSQI1 Sequence of voltages .SeqA.c1.cVal.mag -positive magnitude .SeqA.c2.cVal.mag -negative magnitude .SeqA.c3.cVal.mag -zero magitude LD0.PEMMXU1 Power measurands (1) LD0.PEMMXU1 .TotW.instMag Active power P value 1000 .TotVAr.instMag Reactive power Q value...
Section 3 1MRS757657 A Interoperability profile for 620 series IEC 60870-5-103 Section 3 Interoperability profile for 620 series IEC 60870-5-103 Physical layer 3.1.1 Electrical interface ⊠ EIA RS-485 ⃞ Number of loads ......for one protection equipment NOTE - EIA RS-485 standard defines unit loads so that 32 of them can be operated on one line.
Section 3 1MRS757657 A Interoperability profile for 620 series IEC 60870-5-103 Application layer 3.3.1 Transmission mode for application data Mode 1 (least significant octet first), as defined in 4.10 of IEC 60870-5-4, is used exclusively in this companion standard. 3.3.2 COMMON ADDRESS of ASDU ⊠...
Section 3 1MRS757657 A Interoperability profile for 620 series IEC 60870-5-103 ⃞ <27> Auxiliary input 1 ⃞ <28> Auxiliary input 2 ⃞ <29> Auxiliary input 3 ⃞ <30> Auxiliary input 4 Note <27>...<30>: Depending on Binary I/O options and application usage there may be additional auxiliary inputs available in the IED.
Section 3 1MRS757657 A Interoperability profile for 620 series IEC 60870-5-103 ⃞ <66> Start /pick-up L ⃞ <67> Start /pick-up N ⊠ <68> General trip ⃞ <69> Trip L ⃞ <70> Trip L ⃞ <71> Trip L ⃞ <72> Trip I>> (back-up operation) ⃞...
Section 3 1MRS757657 A Interoperability profile for 620 series IEC 60870-5-103 3.3.3.7 Measurands in monitor direction Semantics ⊠ <144> Measurand I ⊠ <145> Measurands I, V ⊠ <146> Measurands I, V, P, Q ⊠ <147> Measurands I ⊠ <148> Measurands I...
Section 3 1MRS757657 A Interoperability profile for 620 series IEC 60870-5-103 3.3.5 Basic application functions ⊠ Test mode ⃞ Blocking of monitor direction ⊠ Disturbance data ⃞ Generic services ⊠ Private data 3.3.6 Miscellaneous Measurands are transmitted as Class2 data using ASDU 3 or ASDU 9. The default MVAL scalings in this IED series is 2.4.
Section 4 1MRS757657 A Glossary Section 4 Glossary Autoreclosing ASDU Application-layer service data unit Double-point information Electromagnetic compatibility Human-machine interface International Electrotechnical Commission IEC 60870-5-103 1. Communication standard for protective equipment 2. A serial master/slave protocol for point-to-point communication IEC 61850 International standard for substation communication and modeling Intelligent electronic device...
Page 72
Contact us ABB Oy Medium Voltage Products, Distribution Automation P.O. Box 699 FI-65101 VAASA, Finland Phone +358 10 22 11 +358 10 22 41094 www.abb.com/substationautomation...