ADC H2TU-C-202 User Manual page 26

Provisioning
Table 6. H2TU-C-202 List 3F ADC Config Menu Options (Continued)
Front-Panel
ADC Config
Display
Menu Options
Code
Special Loopback SPLB
Mode
SmartJack Loopback LPBK
Minor Alarm ALM
Remote Disconnect RDA
Alarm
Network AIS Signal NAIS
Performance Report PRM
Messaging
RAI to RAI-CI RACI
Toward NET
See "RAI to RAI-CI
toward NET (RACI)"
on page 23.
ESF-RAI to SF-RAI ROVR
Overwrite
See "ESF-RAI to
SF-RAI Overwrite
(ROVR) Option" on
page 22.
18
Selection Description
GNLB Configures the HDSL2 system to respond to the generic inband loopback codes.
A1LB and Configures the HDSL2 system to respond to the inband loopback codes of the
A2LB Westell addressable repeater.
A3LB Configures the HDSL2 system to respond to the inband loopback codes of the
Wescom addressable repeater.
A4LB Configures the HDSL2 system to respond to the inband loopback codes of the
Wescom Mod 1 addressable repeater.
A5LB Configures the HDSL2 system to respond to the inband loopback codes of the
Westell Mod 1 addressable repeater.
ENA Enables the HDSL2 system to recognize all inband SmartJack (SMJK) loopback
commands.
DIS Configures the HDSL2 system to ignore all inband SmartJack loopback
commands.
ENA Enables the generation of the output alarm on pins 30 and 22 when a system
alarm condition occurs.
DIS Disables the generation of the output alarm on pins 30 and 22 when a system
alarm condition occurs.
ENA Enables a remote DS1 LOS condition at the input to the H2TU-R to generate an
LOS alarm. AIS or LOS (depending on ALMP) is sent toward the network.
DIS Prevents a remote DS1 LOS condition at the input to the H2TU-R from causing
an LOS alarm. The alarm relay contacts do not close and LOS is sent toward the
network from the H2TU-C instead of AIS.
CI If ALMP is set to AIS, this option specifies which pattern is sent to the network
when a remote LOS or AIS occurs. When configured for CI, an AIS-CI pattern is
sent to the network. For priority resolution, see
AIS When configured for AIS, an AIS pattern is sent to the network.
SPRM The H2TU-R generates SPRM if no PRM is present from the CPE. If the CPE is
sending PRM, the PRM is converted to an SPRM. TL1 commands and
responses are enabled.
NPRM The H2TU-R generates Network PRM (NPRM) if no PRM is present from the
CPE. If the CPE is sending PRMs, NPRM is generated in addition to the existing
PRM every second. TL1 commands and responses are enabled.
AUTO The H2TU-R generates both SRPMs and NPRMs whenever possible.
OFF ESF Data Link (DL) is completely transparent. No PRMs are generated. There
are no TL1 responses unless the system is first armed by a TL1 command,
which enables Performance Monitoring (PM).
ENA Allows a DS1 RAI (yellow alarm) signal received by the H2TU-R to be converted
to an RAI-CI signal toward the network.
DIS Prevents conversion of the DS1 RAI to an RAI-CI signal.
ENA If the CONV option is set to FCON or ACON, an ESF DS1 payload from the
network with an embedded RAI pattern is converted to an SF-RAI pattern
toward the CI at the H2TU-R.
DIS Prevents conversion to an SF-RAI pattern.
June 28, 2002
LTPH-UM-1161-01
Figure 30 on page 50.
Continued
H2TU-C-202 List 3F