Related Manuals for Brisas BFG-E36AG
Summary of Contents for Brisas BFG-E36AG
- Page 1 BFG-E30AG BFG-E36AG BMI-E30BG BMI-E36BG BMI-E36BS BVE-E30AS BVE-E36AS Model number: Serial Number: AUG12.0601...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Hood Specifi cations 8-10 ........... Mounting the Hood, BFG ......... Mounting the Hood, BMI ......... Mounting the Hood, BVE........ 13 Ductless Recirculating ..........
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
-
Page 5: Operation
WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. NOT FOR USE IN OUTDOOR COOKING ENVIRONMENTS. CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. -
Page 6: Hardware Package Contents
MODELS: BFG-ExxAG, BMI-ExxBx, BVE-ExxAS PARTS SUPPLIED 1 - Hood with internal blower 1 - Duct cover wall bracket 1 - Duct cover assembly (top and bottom) 1 - 6” round backdraft damper (pre-installed) 2 - 50W GU-10 halogen light bulbs (pre-installed) 1 - Stainless steel mesh filter - BFG &... - Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3- 1/ 4” x 10” 1 Ft. 6”- 8” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6”- 8”...
-
Page 8: Damage - Shipment/Installation
Minimum mount height between range top to hood bottom should be no less than 26”. Maximum mount height should be no higher than 34”. * Min. ducted (A) Min. recirc. (B) Max. It is important to install the hood at the proper mounting height. - Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certifi...
- Page 10 ” ” Min. Ducted - 22” Min. Recirc. - 26” Maximum - 42” 11/16 ” ” 30” or 35 ” 7/16 FRONT SIDE 15/16 ” ” ” 15/16 BACK...
- Page 11 ” ” Min. Ducted - 23” Min. Recirc. - 27” Maximum - 42” 15/16 ” ” 30” or 35 3/16 ” FRONT SIDE ” 15/16 ” 15/16 ” BACK...
- Page 12 ” ” Min. Ducted - 27 ” Min. Recirc. - 32” Maximum - 42 ” 15/16 ” or 35 ” ” FRONT SIDE 15/16 ” ” 2" 3-1/2" BACK...
- Page 13 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure from range top to hood bottom and mark line A. (26” minimum from range top) . 2. Plum and mark center line. Duct Cover Bracket 3.
- Page 14 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure from range top to hood bottom and mark line A. (26” minimum from range top) . 2. Plum and mark center line. Duct Cover Bracket 3.
- Page 15 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure from range top to hood bottom and mark line A. Duct Cover Bracket (26” minimum from range top) . 3-1/2" 2" 2. Plum and mark center line. 3.
- Page 16 Note: Refer to manual included with recirculating kit for more detailed installation instructions. Charcoal Filter Replacements Hood Model Part No. Qty to Order All Brisas Models Z0F-C002 DO NOT WASH CHARCOAL FILTERS. Charcoal fi lters may need to be changed more often depending on cooking habits. FIG. B...
- Page 17 Blower Off Lights On/Off Blower Speed Selection Blower Off The blower will be powered off by pressing: Blower Speed Selection Select one of three speed levels by pressing: Lights On/Off Power lights on and off by pressing:...
-
Page 18: Surface Maintenance
SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain. -
Page 19: Replacing Light Bulbs
REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. - Page 20 TROUBLESHOOTING PROCEDURES FOR BRISAS Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 23 DESCRIPTION PART# Replacement Parts Light Bulb GU-10 50W (each) Z0B-0020 Optional Accessories Recirculating Kit BRC-0003 (for BFG) BRC-0005 (for BMI) BRC-0001 (for BVE) Replacement Charcoal Filter Z0F-C002 Duct Cover Extension (up to 12’ ceiling) B1C-00MI (for BMI & BFG) B1C-00VE (for BVE) To order parts, visit us online at www.brisasrangehoods.com or call us at 1.888.880.8368...
- Page 24 STAPLE YOUR RECEIPT HERE Proof of the original purchase date is needed to obtain Limited Warranty service under warranty TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: 1-888-880-8368 Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you”...