Advertisement
Quick Links
Advertisement
Related Manuals for Brisas BML-E30BG
Summary of Contents for Brisas BML-E30BG
- Page 1 BML-E30BG BML-E36BG Model number: Serial Number: MAR19.0101...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Hood Specifications ........... Mounting the Hood 9-11 ............. Ductless Recirculating ..........FEATURES & CONTROLS Touch Controls ............. MAINTENANCE Hood and Filter Cleaning .........
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and install appropriate connector if necessary. BML-E30BG - Max. 325 Watts, 2.7 Amps BML-E36BG - Max. 325 Watts, 2.7 Amps Prop. 65 Warning for California Residents WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov...
- Page 6 PARTS SUPPLIED 1 - Top support frame 2 - Top duct covers Front of Hood Cut-Out Shaded Area 1 - Paper ceiling template 2 - Bottom duct covers 1 - Bottom support frame 1 - 6” round damper (pre-installed) 1 - Hood body w/ blower (pre-installed) 1 - Hardware package 1 - Canopy, glass 2 - 5W LED Light Strips...
- Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3- 1/ 4” x 10” 1 Ft. 3- 1/ 4” x 10” 5 Ft. Rect., Rect. to straight 6” round transition 6”, 7”, 8”, 10” 1 Ft.
- Page 8 Minimum mount height between range top to hood bottom should be no less than 24”. Maximum mount height should be no higher than Min. ducted 28” 34”. Min. recirc. 29” Max. 37” It is important to install the hood at the proper mounting height.
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape.
- Page 10 ” ” Min. Ducted - 28” Min. Recirc. - 29” Maximum - 37” ” 15/16 ” ”, 35 ” 15/16 3/16 ” 9/16 FRONT SIDE 8” ” ” elec. k/o 1 3/4” ” 3/16 TOP of HOOD TOP SUPPORT FRAME (top view)
- Page 11 WARNING: Electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards. This range hood must be properly grounded. Turn off electrical power at service entrance before wiring. PAPER TEMPLATE Front of Hood Ceiling Joists Cut-Out Shaded Area Wood Blocking Top Support Frame...
- Page 12 CAUTION: At least two installers are required due to the weight and size of the hood. BLOWER HOUSING ELECTRONICS MOUNTING BRACKET FIG. E FIG. F FIG. D 5. Remove tape securing electronics mounting bracket to hood. (FIG. D, #1) Remove (3) screws from top of hood body and set screws aside.
- Page 13 Top Support Frame Top Duct Covers Bottom Duct Covers Bottom Support Frame FIG. G 10. Assemble Top Duct Covers (with louver holes) together over Top Support Frame, secure Top Duct Covers together by magnetic strips. Note: If using hood in ductless recirculating mode you must install the air diverter plate to the Top Support Frame prior to assembling the duct covers.
- Page 14 Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and filtered by a set of optional charcoal filters. The air is then purified and re-circulated back within the home.
- Page 15 On/Off Lights On / Off - On/O o button will turn power on and o for the entire hood (fan and lights). - The hood will remember the last speed and light level it was last turned o at. - Delay O Feature: With the fan on, press and hold the On/O button for three seconds. The fan will change to speed 1 and automatically turn o after 5 minutes.
- Page 16 SURFACE MAINTENANCE: Do not use corrosive detergents, abrasive detergents or oven cleaners. Do not use any product containing chlorine bleach or any product containing chloride. Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface. Cleaning Stainless Steel Clean periodically with warm soapy water and clean cotton cloth or micro fiber cloth.
- Page 17 LED LIGHT STRIPS In the unlikely event that your LED strip fails, please contact Zephyr to order replacement parts. See list of parts and accessories page for part #’s and contact information. To replace LED light strip 1. Remove aluminum mesh filters. 2.
- Page 18 AIRFLOW CONTROL TECHNOLOGY (ACT) Some local codes limit the maximum amount of CFM a range hood can move. ACT allows you to control the maximum blower CFM of the range hood without the need for expensive make up air kits. ACT enables the installer to easily set the maximum blower speed to one of two most commonly specified CFM levels;...
- Page 19 Model:BML-E30BG BML-E36BG Voltage 120V 60Hz Power consumption Total: Max.325W @ 2.7A Lamp: LED 5W*2 Fan: 315W On/O Lights THERMALLY PROTECTED UL file number: E127334...
- Page 20 TROUBLESHOOTING PROCEDURES FOR BRISAS Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 21 DESCRIPTION PART# Replacement Parts LED Light Strip, 5W Z0B0043 Aluminum Mesh Filter 50200043 Optional Accessories Recirculating Kit BRC-0007 Replacement Charcoal Filter Z0F-C094 Duct Cover Extension (up to 12’ ceiling) B1C-00ML To order parts, call us at 1.888.880.8368...
- Page 22 Zephyr Ventilation, LLC (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or workmanship as follows: One Year Limited Warranty for Parts: For one year from the date of your original purchase of the Products, we will provide, free of charge, Products or parts (including LED light bulbs, if applicable) to replace those that failed due to manufacturing defects subject to the exclusions and limitations below.