Advertisement
Available languages
Available languages
You may notice that all the dust will not come free from the bag. This will
not affect cutting performance but will reduce the saw's dust collection
efficiency. To restore your saw's dust collection efficiency, depress the spring
inside the dust bag when you are emptying it and tap it on the side of the
trash can or dust receptacle.
External Dust Extraction
When vacuuming dry dust that is especially detrimental to health or
carcinogenic, use a special dust Class M vacuum cleaner.
connecting to an airLock compatable Dust Extractor (Fig. U)
The dust port
30
on your mitre saw is compatable with the D
AirLock connection system. The AirLock allows for a fast, secure connection
between the dust extractor hose and the mitre saw.
1. Ensure the collar on the AirLock connector
Align notches on collar and AirLock connector as shown for unlock and
lock positions.
2. Push the AirLock connector onto the dust port
3. Rotate the collar to the locked position.
nOTE: The ball bearings inside collar lock into slot and secure
the connection.The mitre saw is now securely connected to the
dust extractor.
MAINTENANCE
Your D
WALT power tool has been designed to operate over a long period
e
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of serious personal injury, turn
machine off and disconnect battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start-up can cause injury.
WARNING: If the saw blade is worn replace it with a new sharp blade.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Before use, carefully check the upper blade guard, movable lower blade
guard as well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or workpiece particle cannot lead to
blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and guards
disconnect the machine from the power supply and follow the instructions
given in section Changing or Installing a New Saw Blade. Remove the
jammed parts and reassembling the saw blade.
WARNING: Blow dirt and dust out of the main housing with dry air
as often as dirt is seen collecting in and around the air vents. Wear
approved eye protection and approved dust mask when performing
this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning
the non-metallic parts of the tool. These chemicals may weaken the
materials used in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
WARNING: To reduce the risk of injury, regularly clean the
table top.
WARNING: To reduce the risk of injury, regularly clean the dust
collection system.
Optional Accessories
Range of saw blades available (recommended blades)
DT4310 series 40
WALT
e
DT4286 series 40
DT4320 series 60
45
is in the unlock position.
DT4350 series 60
30
.
DT99568-QZ
DT99569-QZ
DT99570-QZ
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
electrical products and batteries according to local provisions. Further
information is available at www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to produce
sufficient power on jobs which were easily done before. At the end of its
technical life, discard it with due care for our environment:
•
•
WARNING: Since accessories, other than those offered by D
have not been tested with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of injury, only D
recommended accessories should be used with this product.
Type of blade
Blade dimensions
(diameter x bore x no. of teeth)
216x30x24
216x30x80
216x30x48
216x30x60
216x30x24
216x30x36
216x30x60
Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle
Run the battery pack down completely, then remove it from the tool.
Li-Ion cells are recyclable. Take them to your dealer or a local recycling
station. The collected battery packs will be recycled or disposed
of properly.
EnGLIsh
WALT,
e
WALT,
e
Usage
For general purpose, ripping and cross-
cutting of wood and plastics
TCG for use with aluminum
ATB for fine cutting of manmade and
natural wood
TCG for extra fine cutting of manmade and
natural wood
24T Flexvolt blade for general purpose,
ripping and cross cutting
36T Flexvolt blade for fine cutting
60T Flexvolt blade for ultra-fine cutting
43
Advertisement
