Page 1: Table Of Contents
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3 CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With The Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Keyless Entry .....21 To Unlock The Doors ....21 To Lock The Doors .
Page 11: Things To Know Before Starting Your Vehicle
Engine Break-In Recommendations ...56 Safety Tips ......57 Exhaust Gas .
Page 12: 12 Things To Know Before Starting Your Vehicle
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 14: Locking Doors With The Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever.
Page 15 chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
Page 17: General Information
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
Page 18: Automatic Transaxle Ignition Interlock System
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push-button is out.
Page 19: Power Door Locks
WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death.
Page 20: Central Locking/Unlocking
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking/Unlocking All vehicle doors and deck lid are locked with the first turn of the key to the LOCK position. The double unlock activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors at once.
Page 21: Remote Keyless Entry
2. Cycle the ignition switch ON/OFF four times ending in the OFF position. 3. Press the interior door lock switch to the LOCK position. 4. A single chime will sound to signify that you have successfully completed the programming. You can turn the feature back on by repeating the above mentioned procedure.
Page 22: To Lock The Doors
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Doors: Press and release the LOCK button to lock all doors. The park lights will flash and the horn will chirp to acknowl- edge the signal. Horn Chirp Feature The horn chirp that signals that the doors have been locked can be turned on or off by using the following procedure:...
Page 23: To Program Transmitters
To Program Transmitters Up to four transmitters can be programmed to your vehicle. Your new vehicle was shipped with two trans- mitters. See your dealer for additional transmitters. Additional transmitters can be programmed to the sys- tem by using the following procedure: 1.
Page 24: Transmitter Battery Service
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Service The recommended replacement battery is 2016 or its equivalent. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With the transmitter buttons facing down, use a thin coin to pry the two halves of the transmitter apart.
Page 25: Security Alarm System
SECURITY ALARM SYSTEM The system monitors the doors, deck lid, and ignition switch for unauthorized operation. If something triggers the alarm, the system will signal for about 18 minutes. For the first 3 minutes the horn will sound and the headlights, park lights, tail lights and the indicator light in the cluster will flash.
Page 26: To Disarm The System
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To disarm the system: Unlock a front door/deck lid using either the key or the Keyless Entry Transmitter. Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle.
Page 27: Power Deck Lid Release
To open the deck lid, insert the key into the lock and turn to the right. The deck lid can also be opened using the remote keyless entry or by using the power deck lid release switch, located in the glove box. WARNING! •...
Page 28: Emergency Deck Lid Release Latch
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE EMERGENCY DECK LID RELEASE LATCH WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the deck lid when your vehicle is unattended.
Page 29: Auto Down Feature
The lower left switch controls the left rear passenger’s window and the lower right switch controls the right rear passenger’s window. Power Window Switches THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! Never leave children in a vehicle, with the keys in the ignition switch.
Page 30: Wind Buffeting
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down. This is a normal occurrence and can be minimized.
Page 31: Lap/Shoulder Belts
Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 35 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 37: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. Seat Belt Webbing Guide Positioning Latch Plate...
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. Creating A Fold 3.
Page 39: Seat Belt Pretensioners
Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
Page 40: Driver And Front Passenger Supplemental Restraint System (Srs) - Airbag
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
Page 41 If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. Side Airbags THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection.
Page 43 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbag system consists of the following: • Airbag Control Module (ACM) • AIRBAG Readiness Light • Driver and Passenger Front Airbag/Inflator Units • Unique Steering Wheel and Column • Unique Instrument Panel •...
Page 45 bolster, instrument panel and the steering wheel and column. If the key is in the OFF position, in the ACC position, or not in the ignition switch, the airbags are not on and will not inflate. The airbag control module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition switch is first turned ON, then turns the light off.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE panel. The passenger’s front airbag gas is vented through vent holes in the sides of the airbag. In this way the front airbags do not interfere with your control of the vehicle. •...
Page 47 If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you.
Page 49: Child Restraint
Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child.
Page 51 • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s cushion while the child’s back is against the seat back;...
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
Page 53 around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
Page 55 Tether Strap Mounting Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. NOTE: If your child restraint seat is not LATCH com- patible, install the restraint using the vehicle seat belts. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! An incorrectly anchored tether strap could lead to...
Page 56: Engine Break-In Recommendations
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
Page 57: Safety Checks You Should Make Inside The
A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill.
Page 58: Periodic Safety Checks You Should Make Outside The Vehicle
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt.
Page 59 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....62 To Lower The Top ..... .62 To Raise The Top .
Page 60 60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Seat Back Tilt ....82 Passenger Seat Back Tilt (Easy Entry System) . . .83 Adjustable Head Restraints .
Page 61 Electronic Speed Control ....103 To Activate ......103 To Set At A Desired Speed .
Page 62: 62 Understanding The Features Of Your Vehicle
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.
Page 63 CAUTION! To fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position (automatic transaxle) or in the Neutral position (manual transaxle) before lowering or raising the top. CAUTION! Do not operate the convertible top with ice or snow build-up on the top.
Page 64 64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Turn the ignition key to the ON position. 2. Release the top from the windshield header by pulling down on the latch handle and turning the latch handle clockwise until it stops. Releasing Convertible Top Latches 3.
Page 65 Convertible Top Switch 4. Continue pressing the Power Top Switch until the convertible top is lowered completely. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 5. Install the Convertible Top Boot Cover, if equipped. Refer to Convertible Top Boot Cover Installation–If Equipped, in this section.
Page 66: To Raise The Top
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise The Top: CAUTION! To avoid damage to the convertible top or its com- ponents, your vehicle is equipped with a feature that prevents convertible top operation at speeds over 10 mph (16 km/h). CAUTION! To fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear...
Page 67 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 CAUTION! Car top carriers, ski racks, etc., should not be at- tached to the convertible top mechanism as they will damage the top. Do not place objects on the convert- ible top, in the top well or on the sport bar. Damage to the convertible top may occur.
Page 68: Convertible Top Boot Cover Installation-If Equipped
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Boot Cover Installation–If Equipped 1. With the top down and the convertible top latch handle in the stowed position, lay the unfolded boot cover across the convertible top. Boot Laying Across Convertible Top Convertible Top Latch Handle...
Page 69 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 2. Install the rear edge of the boot, first tucking the rear edge of the boot under the rear and both sides of the rails. Tucking Boot Under Rail...
Page 70 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the right and left boot arms forward and engage both boot arm snaps. Make sure both snaps are fully engaged. Engaging Boot Arm Snaps 4. Engage the boot center section retainer using the tabs provided.
Page 71 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 5. Tuck the rear flap of the boot in behind the Upper Moulding. Tucking In Rear Flap...
Page 72: Convertible Top Boot Cover Removal And Storage
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Boot Cover Removal and Storage 1. Unsnap the snaps and remove the top cover boot. 2. Lay the boot cover flat with the center section retainer facing the rear of the car. Boot Removed And Laying Flat 3.
Page 73: Convertible Top Manual Override
4. Second fold the right side of the boot cover to the middle, fitting it inside the left side of the boot cover and store it in the trunk or a dry secure area. Folding Boot Cover Right Side UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 CAUTION! Do not lay heavy objects on top of the boot or lay the boot on top of sharp/pointy objects.
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Turn the screw counterclockwise until the screw stops. This will relieve the hydraulic pressure and allow the convertible top to be raised manually. Bleeder Screw 3. Using the latch handle raise the top until the two pins seat themselves in the windshield header.
Page 75: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 MIRRORS Inside Compass/Temperature Mirror This manual day-night inside rearview mirror has an integrated compass and outside temperature display, along with dual map/courtesy lamps with switches for independent operation. These lamps also turn on to- gether with the dome lamp.
Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights • Briefly press the “Right” button to toggle the right reading lamp “ON/OFF”. Repeat the key press to cycle the light. • Briefly press the “Left” button to toggle the left reading lamp “ON/OFF”. Repeat the key press to cycle the light.
Page 77 Compass Variance • Find your current location and determine the correct Zone number from the map. • Press and hold the “Left” button for 5–10 seconds (until “Zone” appears in the display), then release the button. The number displayed is the current Zone value.
Page 78: Outside Mirror-Driver's Side
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Calibration If “CAL” is not displayed, press and hold the “Left” button for 10–15 seconds, until “CAL” appears in the display, then release the button. The compass is now in calibration mode. The mirror can be calibrated in one of two ways •...
Page 79: Electric Remote-Control Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Electric Remote-Control Mirrors Use the mirror select switch, located to the left of the steering column on the instrument panel, to adjust the view obtained in the outside mirrors. Press the L or R button for Left or Right mirror selection.
Page 80: Illuminated Vanity Mirrors
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights. Illuminated Vanity Mirror SEATS Front Seat Adjustment...
Page 81: Driver's Power Seat Height Adjuster - If Equipped
Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
Page 82: Reclining Bucket Seats
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Bucket Seats The recliner control is on the outboard side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
Page 83: Passenger Seat Back Tilt (Easy Entry System)
The driver’s front seat has a full recliner NOTE: memory, which will allow the seat back to return to its original position. Driver’s Seat Back Tilt Handle UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Passenger Seat Back Tilt (Easy Entry System) How to operate the passenger front seat: 1.
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passenger Seat Back Tilt Handle 3. Continue pushing the entire seat forward until it slides toward the dashboard. 4. To return seat to a sitting position, rotate seat back upright until it locks. 5.
Page 85: Adjustable Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraints so that the upper edge is as high as practical.
Page 86: Heated Seats - If Equipped
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats the front driver’s and passenger’s seats. The control for the heater is located on the out- board side of each seat. After turning on the ignition, you may choose from HIGH, or LOW heat settings.
Page 87: Folding Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. The seat back release knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
Page 88: Tumbling Rear Seat
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 To tumble the seat forward use the following procedure: 1. The seat back release knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. From inside the vehicle, fold the rear seat back down flat. Folding Rear Seat Back 3. Pull the release handle located at the bottom of the folded seat back and tumble the seat forward. Tumbling Rear Seat...
Page 91 4. Attach the cinching tether strap, located at the side of the seat cushion, onto the hook bar on the center trim panel and tighten by pulling the cinching strap until the seat is secure. Cinching Tether Strap To return the tumbling rear seat to the latched (normal) position use the following procedure: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 1.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Prior to rotating the seat cushions reward, be sure that the rear seat belt buckles are secured with the straps, so that the buckles are accessible. Rear Seat Belt Buckle Straps NOTE: Prior to lifting either seatback to the upright position, be sure that the seat belt is brought forward to avoid trapping it behind the seatback.
Page 93: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Hood Release Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Then move the safety catch located under the front edge of the hood, near the center and slightly to the right, and raise the hood.
Page 94: Lights
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Interior Lights The interior lights come on when a door or the deck lid...
Page 95: Multi-Function Control Lever
Interior light Defeat (OFF) Rotate the dimmer control to the ex- treme bottom “OFF” position. The in- terior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (white semi-circle). This feature brightens the odometer and radio dis- play when the parking lights or head- lights are on during daylight condi-...
Page 96: Headlights, Parking Lights, Instrument Panel Lights
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Multi-Function Control Lever To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.
Page 97: Fog Lights
Fog Lights The front fog light switch is on the Multi-Function Control Lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control lever. NOTE: The fog lights will only operate with the head- lights on low beam.
Page 98: Windshield Wipers And Washers
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Move the con- trol lever up to select the desired wiper speed. Windshield Wiper/Washer Control Windshield Washers To use the washer, pull the control lever toward you and...
Page 99: Windshield Wiper Operation
CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.
Page 100: Adding Washer Fluid
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adding Washer Fluid The fluid reservoir is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
Page 101: Tilt Steering Column
TILT STEERING COLUMN To tilt the column, push down on the lever below the multi-function control lever and move the steering wheel up or down, as desired. Pull the lever back up to lock the column firmly in place. Tilt Steering Column Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 WARNING! Tilting the steering column while the vehicle is...
Page 102: Traction Control Switch - If Equipped
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL SWITCH — IF EQUIPPED The TRAC indicator, located in the instrument cluster, will flash when the Traction Control System is in use. The TRAC OFF switch is located on the instrument panel below the radio.
Page 103: Electronic Speed Control
NOTE: The Traction Control System indicator “TRAC OFF” will illuminate momentarily as a bulb check, each time the ignition switch is turned ON. This will occur even if you used the “TRAC OFF” switch to turn the system OFF. NOTE: The Traction Control System will make buzzing or clicking sounds when the system is in operation.
Page 104: To Set At A Desired Speed
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.
Page 105: Manual Transaxle
Tapping “ACC/RES” once will result in a 2 mph (3 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 6 mph (10 km/h), etc. To decrease speed while speed control is ON, push down and hold “COAST/SET”.
Page 106: Garage Door Opener - If Equipped
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
Page 107: Programming The Universal Transceiver
WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 108 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
Page 109: Rolling Code" Programming
5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4.
Page 110: Canadian Programming/Gate Programming
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The assistance of a second person may make the following programming procedure quicker and easier. 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer.
Page 111: Operation
The Universal Transceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor. Operation Press and hold the desired button on the Universal Transceiver until the garage door or other device begins to operate.
Page 112: Electrical Power Outlets
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 113 Another of the outlets is in the Accessory Switch Bank, in the center of the instrument panel. Power Outlet UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 This outlet is powered directly by the battery, regardless of the ignition switch position. All accessories connected to this outlet should be removed or turned off when the vehicle is not in use, to protect the battery against discharge.
Page 114: Electrical Outlet Use With Engine Off
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Since this outlet is remote from the driver, it is powered by the ignition switch, only when it is in the ON or ACCESSORY positions, to protect the battery against discharge. Note: Neither of the power outlets will accept a cigar lighter unit.
Page 115: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 CONSOLE FEATURES The console has two front cup holders, a coin holder, 12 volt power outlet, and front and rear storage trays. There are additional cup holders; one is molded in the center of the console to hold large cups and the other is at the rear of the console to serve passengers in the rear seat.
Page 116: Storage
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine start- ing.
Page 117: Storage Pockets
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Storage Pockets There are also Storage pockets located on each door trim panel.
Page 119: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....123 Instrument Cluster ..... . 124 Instrument Cluster—Turbo, With AutoStick .
Page 120 120 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning ......137 Radio Data System (RDS) ....137 PTY (Program Type) Button .
Page 121 Mode ......144 Tape CD Button ..... . 144 Time Button .
Page 122 122 UNDERSTANDING YOUR INSTRUMENT PANEL CD Changer Control Capability — If Equipped ..... . . 157 Radio Display Messages ....158 Sales Code RBQ—AM/FM Stereo Radio With 6 - Disc CD Changer .
Page 123: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 123 INSTRUMENT PANEL FEATURES...
Page 124: Instrument Cluster
124 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 125: Instrument Cluster-Turbo, With Autostick
UNDERSTANDING YOUR INSTRUMENT PANEL 125 INSTRUMENT CLUSTER—TURBO, WITH AUTOSTICK...
Page 126: Instrument Cluster-Turbo, Without Autostick
126 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—TURBO, WITHOUT AUTOSTICK...
Page 127: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Charging System Light This light shows the status of the electrical charg- ing system.
Page 128 128 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Engine Temperature Warning Light This light warns of an overheated engine condi- tion. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 7.
Page 129 9. Speedometer Indicates vehicle speed. 10. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever toward the steer- ing wheel to switch the headlights from high or low beam. 11. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range.
Page 130 130 UNDERSTANDING YOUR INSTRUMENT PANEL out of the retractor. This is a reminder to “buckle up”. If you do not buckle up, the light will remain on. 14. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application.
Page 131 The light will also come on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. If the parking brake is off and the light remains on, have the brake system inspected as soon as possible.
Page 132 132 UNDERSTANDING YOUR INSTRUMENT PANEL and trip distance. In the trip odometer mode, holding the trip button for more than 2 seconds will reset the trip odometer to “0”. 19. Cruise Indicator — If Equipped This indicator shows that the Speed Control System is ON.
Page 133 disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the TRAC OFF Light. 22. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems.
Page 134: Electronic Digital Clock
134 UNDERSTANDING YOUR INSTRUMENT PANEL 25. AutoStick Gear Position— If Equipped This vacuum fluorescent display indicator illuminates when the gearshift lever is moved to the AutoStick position and shows the current gear selection. 26. Fuel Door Reminder This symbol is a reminder that the Fuel Filler Door is located on the front passenger’s (right) side of the vehicle.
Page 135: Radio General Information
RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help you understand and save you concern about these “ap- parent”...
Page 136: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls
136 UNDERSTANDING YOUR INSTRUMENT PANEL remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS RAZ Radio Operating Instructions —...
Page 137: Tuning
Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Radio Data System (RDS) The Radio Data System allows radio broadcasting sta- tions to send data signals on a subcarrier frequency...
Page 138 138 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft...
Page 139: Balance
Pressing PTY, then SCAN will scan the FM Band and stop at all RDS stations. Each RDS station will be played for a 5 second scan once around the FM Band and stop at the last station. The PTY icon will then turn off. Balance The Balance control adjusts the left-to-right speaker bal- ance.
Page 140: To Set The Radio Push-Button Memory
140 UNDERSTANDING YOUR INSTRUMENT PANEL To Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
Page 141: Fast Forward (Ff)
Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
Page 142: Pinch Roller Release
142 UNDERSTANDING YOUR INSTRUMENT PANEL Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play.
Page 143: Seek Button
If the volume control is ON, the unit will switch from radio to CD mode and begin to play. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: •...
Page 144: Ff/Tune/Rw
144 UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play.
Page 145: Time Button
Time Button Press this button to change the display from elapsed CD playing time to time of day. Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. CD Changer Control Capability —...
Page 146: Sales Code Rbb-Am/Fm Stereo Radio With Cassette Tape Player And Cd Changer Capability
146 UNDERSTANDING YOUR INSTRUMENT PANEL CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display.
Page 147: Operating Instructions
Operating Instructions NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. NOTE: When first learning the control functions, the user should set the controls as shown in the following list.
Page 148: Tune
148 UNDERSTANDING YOUR INSTRUMENT PANEL Tune Press the TUNE control up or down to increase or decrease the frequency. If the button is pushed and held, the radio will continue to tune until the button is released. The frequency will be displayed and continu- ously updated while the button is pushed.
Page 149: Bass And Treble Tone Control
Bass and Treble Tone Control The tone controls consist of 2 separate bands. The bass band is on the left, and the treble band is on the right. Each band is adjusted by a slider control with a detent at the mid-position.
Page 150 150 UNDERSTANDING YOUR INSTRUMENT PANEL beginning of the previous selection if the tape is within the first 5 seconds of the current selection. The SEEK symbol appears on the display when Music Search is in operation. Music Search shuts off automati- cally when a selection has been located.
Page 151: Cd Changer Control Capability - If Equipped
CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The fol- lowing instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display.
Page 152: Radio Display Messages
152 UNDERSTANDING YOUR INSTRUMENT PANEL A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: •...
Page 153: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS RBK Radio UNDERSTANDING YOUR INSTRUMENT PANEL 153 Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
Page 154 154 UNDERSTANDING YOUR INSTRUMENT PANEL the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Balance The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in.
Page 155: Cd Player Operation
both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed.
Page 156 156 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number and index time in minutes and seconds.
Page 157: Cd Changer Control Capability - If Equipped
Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SA” will appear in your radio display. A CD or tape may remain in the player while in the Satellite mode.
Page 158: Radio Display Messages
158 UNDERSTANDING YOUR INSTRUMENT PANEL Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily.
Page 159: Sales Code Rbq-Am/Fm Stereo Radio With 6 - Disc Cd Changer
UNDERSTANDING YOUR INSTRUMENT PANEL 159 SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER RBQ Radio...
Page 160: Radio Operation
160 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 161 Balance — BAL The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The Fade control provides for balance between the front and rear speakers.
Page 162: Cd Player Operation
162 UNDERSTANDING YOUR INSTRUMENT PANEL General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
Page 163 show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load”...
Page 164 164 UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play.
Page 165 Program Type Radio Display Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B...
Page 166: Sales Code Rb1-Am/Fm Stereo Radio With Dvd/Gps Navigation System
166 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SCAN button when the PTY icon is displayed, the radio will stop at every PTY station on the band and list each corresponding program type in the radio display. Time Press the TIME button to change the display from elapsed CD playing time to time of day.
Page 167: Cassette Tape And Player Maintenance
variety of destinations and routes. Refer to your “Navi- gation User’s Manual” for detailed operating instruc- tions. NOTE: If your vehicle is not equipped with the CD Changer option, you will not be able to use the Naviga- tion system and the CD Player simultaneously. Always remove the Navigation DVD before inserting another disc.
Page 168: Cd/Dvd Disc Maintenance
168 UNDERSTANDING YOUR INSTRUMENT PANEL As preventive maintenance, clean the head about every 30 hours of use. If you wait until the head becomes very dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple WET cleaning cassette. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions:...
Page 169: Climate Controls
CLIMATE CONTROLS Air Conditioning The Air Conditioning System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, above the radio. UNDERSTANDING YOUR INSTRUMENT PANEL 169 The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere.
Page 170 170 UNDERSTANDING YOUR INSTRUMENT PANEL Fan speeds to the right of OFF are for heater or ventila- tion operation. The fan speed increases as you move the control to the right from the OFF position. Mode Control (Air Direction) The mode control allows you to choose from several pat- terns of air distribution.
Page 171 Air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost Air is directed through the windshield and side window demist outlets.
Page 172 172 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Use this control to regulate the temperature of the air in- side the passenger compart- ment. The blue area of the scale indicates cooler tem- peratures while the red area indicates warmer tempera- tures.
Page 173 In cold or damp weather, the use of the Recirculate position will cause windows to fog on the inside because of moisture build up inside the vehicle. For maximum defogging, select the Outside Air position. If the mode control is in the range between Mix and Defrost and you choose the recirculate mode, the mode control knob will automatically move to the left of the Mix position.
Page 174: Operating Tips
174 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips...
Page 175 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
Page 176: Electric Rear Window Defroster
176 UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors.
Page 177 UNDERSTANDING YOUR INSTRUMENT PANEL 177 CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off after soaking with warm water.
Page 179 STARTING AND OPERATING CONTENTS Starting Procedures ..... 182 Automatic Transaxle ....182 Manual Transaxle .
Page 180 180 STARTING AND OPERATING AutoStick General Information ... . 190 Manual Transaxle Operation ....191 2.4 Liter Turbo— If Equipped ... . . 193 Recommended Shift Speeds .
Page 181 Tire Rotation Recommendations ... . 220 Fuel Requirements ..... . 221 2.4L Standard Engine And 2.4L Standard Turbo Engine .
Page 182: 182 Starting And Operating
182 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
Page 183: Extremely Cold Weather (Below 20°F Or 29°C)
started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
Page 184: After Starting
184 STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time.
Page 185: Automatic Transaxle - If Equipped
TURBOCHARGER COOL DOWN CHART Driving Conditions Normal Driving Aggressive Driving or Heavily Loaded Trailer Tow AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop.
Page 186: Brake/Transmission Interlock System
186 STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 187: Reset Mode
Reset Mode The transaxle is monitored electronically for abnormal conditions. If a condition is detected that could cause damage, the transaxle shifts automatically into second gear. The transaxle remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate.
Page 188 188 STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake.
Page 189 “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive This range should be used for most city and highway driving. It provides smoothest up shifts and down shifts and best fuel economy.
Page 190: Autostick - If Equipped
190 STARTING AND OPERATING AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
Page 191: Manual Transaxle Operation
• Downshifts from third to second gear above 74 mph (119 km/h) and from second to first gear above 41 mph (66 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
Page 192 192 STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. Use each gear in numerical order - do not skip a gear. Be sure the transaxle is in FIRST gear, (not THIRD), when starting from a standing position.
Page 193: 2.4 Liter Turbo- If Equipped
STARTING AND OPERATING 193 The neutral position of the shift lever is located between 2.4 Liter Turbo— If Equipped THIRD and FOURTH gear. This is the position the shifter lever will return to automatically when neutral is se- lected. When shifting into FIFTH gear, be sure to press the shifter lever all the way to the right to avoid acciden- tally selecting THIRD gear.
Page 194: Recommended Shift Speeds
194 STARTING AND OPERATING Recommended Shift Speeds To use your manual transaxle for optimal fuel economy, it should be upshifted as listed in table 1. TABLE 1-MANUAL TRANSAXLE NORMAL AC- CELERATION AND CRUISE SHIFT SPEEDS IN mph (km/h) 1 to 2 2 to 3 GINE MODE...
Page 195: Parking Brake
CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch. To maintain a safe speed and prolong brake life, shift down to 2nd or 1st when descending a steep grade. When turning a corner, or driving up a steep grade, downshift early so that the engine will not be overbur- dened.
Page 196 196 STARTING AND OPERATING NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position. Parking Brake Lever When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park.
Page 197: Brake System
WARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
Page 198: Anti-Lock Brake System (Abs) - If Equipped
198 STARTING AND OPERATING If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop.
Page 199: Power Assisted Steering
WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 200: Traction Control - If Equipped
200 STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin. The system reduces wheel slip and maintains traction at the driving (front) wheels by engaing the brake on the wheel that is losing traction.
Page 201: Tire Safety Information
The system is always in the “ON” mode unless: • The TRAC OFF switch has been used to turn the system off; • There is a Anti-Lock Brake System malfunction; • There is a Traction Control System malfunction; • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures.
Page 202 202 STARTING AND OPERATING NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 203 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 204 204 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 205: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 206: Tire Loading And Tire Pressure
206 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B”...
Page 207 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry STARTING AND OPERATING 207 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
Page 208 208 STARTING AND OPERATING To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.
Page 209 STARTING AND OPERATING 209...
Page 210: Tires-General Information
210 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 211: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 212 212 STARTING AND OPERATING The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation.
Page 213 Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits.
Page 214: Radial-Ply Tires
214 STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 215: Limited Use Spare - If Equipped
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the...
Page 216: Tire Spinning
216 STARTING AND OPERATING WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly.
Page 217: Replacement Tires
These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
Page 218: Alignment And Balance
218 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 219: Tire Chains
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Due to limited clearance, tire chains are not recom- mended.
Page 220: Tire Rotation Recommendations
220 STARTING AND OPERATING Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns.
Page 221: Fuel Requirements
FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard Turbo Engine Your vehicle is designed to meet all emis- sion regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended.
Page 222: Reformulated Gasoline
222 STARTING AND OPERATING Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
Page 223: Mmt In Gasoline
MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles.
Page 224: Carbon Monoxide Warnings
224 STARTING AND OPERATING • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service.
Page 225: Adding Fuel
• Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 226 226 STARTING AND OPERATING CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
Page 227: Vehicle Loading
WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants ..... . . 2 Rear Seat Occupants .
Page 228: Warranty
228 STARTING AND OPERATING Warranty To maintain warranty coverage, follow the requirements and recommendations in this manual concerning ve- hicles used for trailer towing. However the following conditions must be met: • The maximum frontal area of the trailer cannot exceed 20 square feet (1.86 square meters).
Page 229 • Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety. • The automatic transaxle fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation.
Page 231 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....232 If Your Engine Overheats ....233 Jacking And Tire Changing .
Page 232: 232 What To Do In Emergencies
232 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Flasher Switch The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash.
Page 233: If Your Engine Overheats
IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transaxle in neutral, but do not increase engine idle speed.
Page 234 234 WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
Page 235: Jacking And Tire Changing
JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 236: Spare Tire Stowage
236 WHAT TO DO IN EMERGENCIES Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism. To re- move or stow the compact spare, use the jack handle to rotate the “spare tire drive”...
Page 237: Preparations For Jacking
Spare Tire Removal Lift up the plastic cover on the scuff plate and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire.
Page 238: Jacking Instructions
238 WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench.
Page 239 Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire.
Page 240: Jump-Starting Procedures Due To A Low Battery
240 WHAT TO DO IN EMERGENCIES 100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free.
Page 241 WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- axle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle.
Page 242 242 WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water.
Page 243: Driving On Slippery Surfaces
8. When removing the jumper cables, reverse the se- quence exactly. Be careful of the moving belts and fan. DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left.
Page 244: Freeing A Stuck Vehicle
244 WHAT TO DO IN EMERGENCIES 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop.
Page 245: Towing A Disabled Vehicle
CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55km/h). WHAT TO DO IN EMERGENCIES 245 TOWING A DISABLED VEHICLE With Ignition Key Four Speed Automatic Transaxle Your vehicle may be towed under the following condi-...
Page 246: Without The Ignition Key
246 WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in the LOCK or ACCESSORY positions. Do not attempt to use sling type equipment when towing.
Page 247: Convertible Top Manual Override
CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bleeder screw, which is found in the trunk under the convertible top storage area.
Page 248 248 WHAT TO DO IN EMERGENCIES 5. Pull down and rotate the handle counterclockwise to engage the latches. Engaging Convertible Top 6. Raise the handle into the stowed position. 7. Close the convertible top motor bleeder screw by turning the screw clockwise until it stops.
Page 249 MAINTAINING YOUR VEHICLE CONTENTS 2.4L Turbo Engine Compartment ... . 252 2.4L Engine Compartment ....253 Onboard Diagnostic System —...
Page 250 250 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance ... . . 267 Power Steering — Fluid Check ... . 268 Front Suspension Ball Joints ....268 Body Lubrication .
Page 251 Bulb Replacement ..... . 299 Headlight Bulb Replacement ... . . 299 Front Park/Turn Signal/Side Marker Lights .
Page 252: 252 Maintaining Your Vehicle
252 MAINTAINING YOUR VEHICLE 2.4L TURBO ENGINE COMPARTMENT...
Page 253: 2.4L Engine Compartment
MAINTAINING YOUR VEHICLE 253 2.4L ENGINE COMPARTMENT...
Page 254: Onboard Diagnostic System - Obd Ii
254 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 255: Emissions Inspection And Maintenance Programs
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready...
Page 256: Replacement Parts
256 MAINTAINING YOUR VEHICLE a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station.
Page 257: Maintenance Procedures
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 258 258 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Engine Oil Dipstick Checking the oil while the vehicle is on level ground, will improve the accuracy of the oil level readings.
Page 259 • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing. •...
Page 260 260 MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American...
Page 261: Maintenance Schedules
Materials Added To Engine Oils The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental ad- ditives.
Page 262: Spark Plugs
262 MAINTAINING YOUR VEHICLE Special tools are required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control.
Page 263 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 264: Engine Timing Belt
264 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle.
Page 265: Maintenance-Free Battery
For vehicles with a Turbo engine, a small NOTE: amount of oil accumulation in the air cleaner box is normal. The amount will depend on driving style. The air cleaner box should be cleaned out and a new make-up- air filter element should be installed during the normal air filter maintenance procedure.
Page 266 266 MAINTAINING YOUR VEHICLE WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
Page 267: Air Conditioner Maintenance
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time.
Page 268: Power Steering - Fluid Check
268 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 269: Body Lubrication
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, deck lid and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit;...
Page 270: Windshield Washer Reservoir
270 MAINTAINING YOUR VEHICLE 2. Push the release tab shown in the illustration and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield. 3. Install the new blade assembly onto the wiper arm tip until it locks in place.
Page 271: Exhaust System
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged;...
Page 272: Cooling System
272 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
Page 273 With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of coolant from the radiator drain cock. If the cap is sealing properly, the engine coolant (antifreeze) will begin to drain from the coolant recovery bottle.
Page 274 274 MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified engine cool- ants, may result in engine damage that may not be covered under the new vehicle warranty, and de- creased corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emer- gency, it should be replaced with the specified coolant as soon as possible.
Page 275 Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
Page 276 276 MAINTAINING YOUR VEHICLE service attendant of this. As long as the engine operating temperature is satisfactory, the coolant recovery bottle need only be checked once a month. When additional coolant is needed to maintain the proper level, it should be added to the coolant recovery bottle.
Page 277: Hoses And Vacuum/Vapor Harnesses
• Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
Page 278: Brake System
278 MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Mainte- nance Section. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
Page 279 NOTE: Inspection of brake hoses should be done when- ever the brake system is serviced and at every engine oil change. WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately.
Page 280: Automatic Transaxle
280 MAINTAINING YOUR VEHICLE Use only manufacturers recommended brake fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking.
Page 281 CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
Page 282 282 MAINTAINING YOUR VEHICLE 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortable held between the finger tips.
Page 283 CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. To prevent dirt and water from entering the transaxle after checking or replen- ishing fluid, make certain that the dipstick cap is seated properly. Fluid And Filter Changes Automatic transmission fluid and filter should be changed as follows: Maintenance schedule “A”—Turbo Charged Engines –...
Page 284: Manual Transaxle
284 MAINTAINING YOUR VEHICLE Manual Transaxle Lubricant Selection Use only manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 3/16”...
Page 285 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: •...
Page 286 286 MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
Page 287 CAUTION! If your vehicle is equipped with flame or woodgrain graphics, it is recommended that special care be taken when using hand-held pressure washers to clean your vehicle. The pressure of these hand-held car wash wands can vary greatly and could possibly cause damage to the surface of the graphic.
Page 288 288 MAINTAINING YOUR VEHICLE CAUTION! Many wheel cleaners contain acids that may harm the wheel surface. NOTE: Replacement costs for components damaged as a result of not following the recommended cleaning practices are considered the responsibility of the cus- tomer. Interior Care Use Mopar Fabric Cleaner to clean fabric upholstery and carpeting.
Page 289 Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.
Page 290: Convertible Top Care
290 MAINTAINING YOUR VEHICLE 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
Page 291: Cloth Top Additional Cleaning Procedure
a soft, natural bristle scrub brush, and a mild soap solution such as liquid dish washing soap. Do not use detergent. CAUTION! Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic sol- vents, petroleum distillates or plasticizers. always wait until the top is thoroughly dry before lowering it into the storage area.
Page 292: Cloth Top Protection
292 MAINTAINING YOUR VEHICLE Cloth Top Protection For appearance purposes, you may wish to protect your Twillfast™ (cloth) top periodically. A fabric protectant such as Scotchguard is suggested. The top should be clean and dry before application of the protectant. CAUTION! Avoid getting Scotchguard on the surrounding...
Page 293 MAINTAINING YOUR VEHICLE 293 Power Distribution Center...
Page 294 294 MAINTAINING YOUR VEHICLE FUSE Amp/Color 30 Amp/Pink Ignition Start 40 Amp/ Anti-Lock Brake (ABS) Green Pump 40 Amp/ Ignition Run Green 30 Amp/Blue Heated Seats 40 Amp/ Radiator Fan (Low Speed Green Turbo only) 50 Amp/Red High Speed Radiator Fan (Turbo Only) 30 Amp/Blue Anti-Lock Brake (ABS) Solenoid...
Page 295: Interior Fuses
20 Amp/ Power Outlets Yellow Spare 20 Amp/ Fog Lamps (Export Only) Yellow Interior Fuses The fuse access panel is on the left side of the instrument panel next to the steering column. To remove the panel, pull it out, as shown. A label identifying the components and circuits is located on the inside of the cover.
Page 296 296 MAINTAINING YOUR VEHICLE FUSE Amp/Color 25 Amp/ Headlamp Switch Natural 15 Amp/Lt. Park Lamps Blue 20 Amp/ RKE/Door Locks Yellow 20 Amp/ Power Height Adjust Yellow 10 Amp/Red Airbag Run Only 10 Amp/Red B/U Electric Back Light (EBL) NEU SAF 25 Amp/ HVAC Blower Natural...
Page 297: Vehicle Storage
CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected.
Page 298 298 MAINTAINING YOUR VEHICLE Rear Cargo ......T906 Seat Belt Indicator ..... . . LED Security Alarm Indicator.
Page 299: Bulb Replacement
BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Disconnect the electrical connector. MAINTAINING YOUR VEHICLE 299 3.
Page 300: Front Park/Turn Signal/Side Marker Lights
300 MAINTAINING YOUR VEHICLE Front Park/Turn Signal/Side Marker Lights 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. Front Fog Lights —...
Page 301: Back Up Light Bulb
2. Twist the bulb socket 1/4 turn to remove it from the housing. 3. Pull the bulb out of the socket and replace. MAINTAINING YOUR VEHICLE 301 Back Up Light Bulb 1. Remove the screws attaching the back up light to the rear fascia and remove the housing.
Page 302: Fluids And Capacities
302 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter 2.4 Liter Engines (Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meet- ing DaimlerChrysler Material Standard MS-6395.) Cooling System * 2.4 Liter Engines (Mopar Antifreeze/Coolant 5 Year/100,000 Miles Formula) * Includes heater and coolant recovery bottle filled to MAX level.
Page 303: Recommended Fluids, Lubricants And Genuine Parts
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Engine Oil Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
Page 304: Chassis
304 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Fluid. Manual Transmission Fluid. Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4 Automatic Transmission Fluid. Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
Page 305 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..306 Maintenance Schedule ....306 Schedule “B”—All Engines ....309 Schedule “A”—Non Turbo .
Page 306: Emission Control System Maintenance
306 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 307 • Taxi, police, or delivery service (commercial ser- vice).† • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines”...
Page 308 308 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 309: Schedule "B"-All Engines
SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following condi- tions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an Change the manual transaxle fluid every 48,000 miles (77 000 km) if the vehicle is usually operated under one or...
Page 310 310 SCHEDULE “B”—ALL ENGINES NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (164,000 km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the Maintenance Sched- ules section of this manual. If none of these apply to you, and your vehicle is equipped with a Non–Turbo Charged Engine then change your engine oil at every interval shown on...
Page 311 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.* Inspect the Make-up air filter, replace as nec- essary. SCHEDULE “B”—ALL ENGINES 311 3,000 6,000 9,000...
Page 312 312 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as neces- sary.* Replace the Make-up air filter.
Page 313 Miles ( Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter, replace as necessary.* Change the manual transaxle fluid.†...
Page 314 314 SCHEDULE “B”—ALL ENGINES Miles ( Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if neces- sary.
Page 315 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and replace as necessary.* Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals.
Page 316 316 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.†...
Page 317 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
Page 318 318 SCHEDULE “B”—ALL ENGINES * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty. ‡ This maintenance is not required if previously replaced. † This maintenance is required only for police, taxi, limousine type operation, or trailer towing.
Page 319: Schedule "A"-Non Turbo
SCHEDULE “A”—NON TURBO Miles (Kilometers ) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension SCHEDULE “A”—NON TURBO 319 6,000...
Page 320 320 SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles.
Page 321 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed.
Page 322 322 SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV valve and replace if necessary. * ‡ Replace the air cleaner filter. Replace the engine timing belt. * Flush and replace the engine coolant at 120 months, if not done at 102,000 miles.
Page 323: Schedule "A"-Turbo
SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
Page 324 324 SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles. 35,000 40,000 45,000 (56 000) (64 000) (72 000) [42] [48]...
Page 325 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed.
Page 326 326 SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary.
Page 327 Miles (Kilometers) [Month] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV Valve and replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty.
Page 329: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......330 Prepare For The Appointment .
Page 330: Suggestions For Obtaining Service For Your Vehicle
330 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 331: If You Need Assistance
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 332 332 IF YOU NEED CONSUMER ASSISTANCE DaimlerChrysler Motors Corporation Customer Center P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: (800) 992-1997 DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone —(800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P.
Page 333: Warranty Information
contract, call the manufacturer’s Service Contract Na- tional Customer Hotline at 1-800-521-9922. The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to...
Page 334 334 IF YOU NEED CONSUMER ASSISTANCE U.S. ONLY...
Page 335: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 336: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 337: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 338: Temperature Grades
338 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade is based on braking (straight- ahead) traction tests and does not include cornering (turning) performance. Temperature Grades The temperature grades are A (highest), B, and C, repre- senting the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 339 INDEX...
Page 340 340 INDEX ABS (Anti-Lock Brake) System ....198 Adding Engine Coolant (Antifreeze) ..274 Adding Fuel ......225 Adding Washer Fluid .
Page 341 Back-Up Lights ......301 Ball Joints ......268 Battery .
Page 342 342 INDEX Cellular Phone ......168 Center High Mounted Stop Light ... . 301 Central Door Locks .
Page 343 Radiator Cap ......275 Selection of Coolant ....273 Corrosion Protection .
Page 344 344 INDEX Emission Control System Maintenance ..255,306 Engine ......252,253 Break-In Recommendations .
Page 345 Fuel ......221,303 Adding ......225 Additives .
Page 346 346 INDEX High Beam ......97,129 High Beam/Low Beam Select Switch ..97 Passing .
Page 347 Knee Bolster ......44,46 Lane Change and Turn Signals ....128 Lap/Shoulder Belts .
Page 348 348 INDEX Loading Vehicle ......227 Tires ....... 206 Locks Central .
Page 349 New Vehicle Break-In Period ....56 Occupant Restraints ..... . . 30 Octane Rating, Gasoline .
Page 350 350 INDEX Steering ......199,268 Steering, Checking ..... 268 Windows .
Page 351 Seat Belts ......30 And Pregnant Women ....39 Child Restraint .
Page 352 352 INDEX Starting ....... 182 Automatic Transmission ....182 Engine Fails to Start .
Page 353 Quality Grading ..... . . 337 Radial ......214 Replacement .
Page 354 354 INDEX Understanding Your Instrument Panel ..123 Uniform Tire Quality Grades ....337 Universal Transmitter ..... 106 Unleaded Gasoline .
Page 355 NOTES...
Page 356 NOTES...
Page 357 NOTES...
Page 358 NOTES...
Page 359 NOTES...
Page 360 NOTES...

Chrysler 2005 PT Cruiser Convertible Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

TABLE OF CONTENTS

Chapters

Related Manuals for Chrysler 2005 PT Cruiser Convertible

Summary of Contents for Chrysler 2005 PT Cruiser Convertible