Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
The vehicle identification number (VIN) is found on the left front corner of the instrument panel, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Vehicle Identification Number Disclosure Label affixed to a window on your vehicle.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....11 Ignition Key Removal ....11 Key-In-Ignition Reminder .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn Off “Flash Lights On Lock/Unlock” . . .23 General Information ....23 Transmitter Battery Service .
Page 11: Things To Know Before Starting Your Vehicle 9
A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. Vehicle Key The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 be used to order duplicate keys from your dealer.
Page 12: Key-In-Ignition Reminder
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The power window switches, radio, power sunroof, and power outlets will remain active for up to 45 seconds after the ignition switch has been turned off. Opening either front door will cancel this feature. WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Page 13 chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked.
Page 14: Replacement Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
Page 15: General Information
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
Page 16: Door Locks
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel. Door Lock Plunger If the lock knob is up when you shut the door, the door will lock.
Page 17: Power Door Locks
Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. Power Door Lock Switch If you press the power door lock switch while the key is in the ignition, and any front door is open, the power THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 locks will not operate.
Page 18 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Close all doors and place the key in the ignition switch. 2. Cycle the ignition switch ON/OFF four times ending in the OFF position. (do not start the engine) 3. Within 10 seconds of the final cycle, press the interior driver’s door lock switch to the LOCK position.
Page 19: Child Protection Door Lock
4. A single chime will sound to signify that you have successfully completed the programming. The Auto Unlock On Exit feature is enabled when your vehicle is shipped from the assembly plant and can be enabled or disabled by performing the procedure in the Electronic Vehicle Information Center (EVIC), Customer Programmable Features section or by repeating the above mentioned procedure.
Page 20: Remote Keyless Entry
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To activate the system, open the rear door and move the child lock control, located near the door’s rear latch, to the ON position. Child Lock Control When the child lock system is engaged the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 21: To Unlock The Doors And Liftgate
Keyless Entry Transmitter To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors and liftgate. The illuminated entry system also turns on. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: If desired, the “Remote Unlock Driver’s Door 1st”...
Page 22: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Programmable Features of the “Electronic Ve- hicle Information Center (EVIC)” section or by following these steps. 1. Press the LOCK button for 4 to 10 seconds. 2. While the LOCK button is pressed (after 4 seconds), press the PANIC button.
Page 23: To Turn Off "Flash Lights On Lock/Unlock
to manually access the liftgate area. The liftgate will re-lock automatically within 10 seconds once the liftgate is closed. To Turn Off “Flash Lights On Lock/Unlock” NOTE: If desired, the “Flash Lights On Lock/Unlock” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Ve- hicle Information Center (EVIC)”...
Page 24: Transmitter Battery Service
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your Remote Keyless Entry transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 2.
Page 25: Vehicle Theft Alarm
3. To reassemble the transmitter case, snap the two halves together. Make sure there is an even “gap” be- tween the two halves. Test transmitter operation. VEHICLE THEFT ALARM This system monitors the vehicle doors and ignition switch for unauthorized entry or operation. When the alarm is activated, the system provides both audible and visual signals.
Page 26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To disarm the system: Press the UNLOCK button on the keyless entry transmitter. Also, using a valid sentry key and moving the ignition switch to the ON/START posi- tion will disarm the system. If you disarm the system and access the liftgate area, the system must be rearmed, as described previously, when closing the liftgate.
Page 27: Liftgate
The alarm system will be activated when the battery is connected if the system was previously armed. The exterior lights will flash, the horn will sound, and the ignition will not start the vehicle. If this occurs, disarm the system. LIFTGATE The liftgate can be unlocked using the remote keyless entry or by activating the power door lock switches...
Page 28: Power Liftgate - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • In the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the lift- gate trim panel.
Page 29 WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance.
Page 30: Windows
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually. WARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle.
Page 31 Power Window Switches There are single window controls on each passenger door trim panel which operate the passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors.
Page 32: Occupant Restraints
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
Page 33: Lap/Shoulder Belts
NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 37 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 39: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. Creating A Fold 3.
Page 41: Seat Belt Pretensioners
Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
Page 42: Seat Belts And Pregnant Women
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or RUN position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1.
Page 43: Seat Belt Extender
Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender.
Page 44: Driver And Front Passenger Supplemental Restraint System - Airbag
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
Page 45 Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to “Occupant Classification System” in this section). This vehicle may also be equipped with a driver inflat- able knee blocker located on the instrument panel below the steering column.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 47 Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 49 • Interconnecting Wiring • Knee Impact Bolster • Driver Inflatable Knee Blocker • Front Passenger Seat Occupant Classification System (OCS) − Occupant Classification Module − Passenger Airbag Disabled (PAD) Indicator Light − Interconnecting Wiring − Bladder Assembly − Belt Tension Sensor How The Airbag System Works •...
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Also, the ORC turns on the AIRBAG warning light and PAD indicator light in the center of the instrument panel for 6 to 8 seconds for a self-check when the ignition is first turned on. After the self-check, the AIRBAG warning light will turn off.
Page 51 the airbags inflate to their full size. The airbags fully inflate in about 50–70 milliseconds. This is about half of the time it takes to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Knee Impact Bolsters help protect the knees, and position everyone for the best interaction with the front airbag. • If your vehicle contains a Passenger Airbag Disable indicator light, it will be equipped with the Occupant Classification System (OCS).
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The ORC will not allow front airbag deployment in the event of a collision for occupants classified into the empty or child size categories. The PAD indicator light will illuminate indicating that the Passenger Airbag is OFF when the OCS has determined that the occupant size category is a child.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For almost all sizes of properly seated adults, the airbag will be enabled in the event of a collision. For small teenagers and some small adults, depending on size, the airbag may or may not be enabled in the event of a collision.
Page 55 • The Belt Tension Sensor (BTS) is located at the outboard passenger lap belt anchor. The BTS generates a signal based on outboard lap belt tension. This signal is sent to the OCM to ensure that the resultant bladder pressure increase due to applied lap belt tension does not cause a small occupant to be classified as a larger occupant.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover.
Page 57 However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 59: Child Restraint
• The light remains on or flickers after the 6 to 8 second interval. • The light flickers or comes on and remains on while driving. Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The lower anchor bars of the LATCH System are located where the seat back meets the seat cushion. Latch Anchorages The tether anchors are located on the rear surface of the seat. Tether Strap Mounting Child restraint systems designed to be compatible with the vehicles LATCH System are now available.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 When using the LATCH System, always follow the child restraint manufactures installation instructions. NOTE: If your child restraint seat is not LATCH com- patible, install the restraint using the vehicle seat belts. Tether Anchors There are tether strap anchorages behind all second row seating positions and if equipped the driver’s side third...
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the tether anchorage is used in the third row seating position, the strap should be positioned straight over the top of the seatback. Third Row Tether Strap Routing Infants and Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.
Page 63 • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 9 kg (20 lbs). Convertible child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are...
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
Page 65 • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seatbacks and cause serious personal injury.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. Not all child restraint systems will be installed as we have described here.
Page 67: Engine Break-In Recommendations
Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
Page 68: Safety Tips
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
Page 69: Periodic Safety Checks You Should Make Outside The Vehicle
Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer.
Page 71: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......75 Inside Day/Night Mirror ....75 Automatic Dimming Mirror —...
Page 72 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seats ....... . 102 10–Way Driver’s Power Seat —...
Page 73 Lights-On Reminder ....124 Headlight Time Delay ....124 Fog Lights —...
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Garage Door Opener — If Equipped ..138 Programming Homelink ....139 Canadian Programming/Gate Programming .
Page 75: Mirrors
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. Adjusting Rear View Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 76: Automatic Dimming Mirror - If Equipped
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped If the switch is in the “Auto” position the mirror will automatically adjust for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror.
Page 77: Outside Mirror - Driver's Side
Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle.
Page 78: Power Remote-Control Mirrors
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote-Control Mirrors Use the mirror select switch, located on the driver’s door trim panel above the power window switches, to adjust the view obtained in the outside mirrors. Power Mirror Switches Press the rocker switch to the L or R for Left or Right mirror selection.
Page 79: Hands-Free Communication (Uconnect™) - If Equipped
For UConnect Customer Support call 1-877-855-8400 or visit UConnect website (www.chrysler.com/ uconnect). UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation.
Page 80 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE linked to system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages (as equipped). The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system.
Page 81: Operation
The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can either be adjusted from the radio volume control knob, or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™...
Page 82 One of the following vehicle specific websites may also provide detailed instructions for pairing with the brand of phone that you have: NOTE: www.chrysler.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin.
Page 83 • You will be asked to say a four-digit pin number which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process.
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For example, you can say 234-567-8901. The phone number that you enter must be of valid length and combination. The UConnect™ limits the user from dialing invalid combination of numbers. For example, 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits.
Page 85 • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recom- mended. For example, say Robert Smith or Robert instead of Bob. • When prompted, enter the number designation (e.g.: Home, Work, Mobile, or Pager ).
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later using the Phonebook Edit feature.
Page 87: Phone Call Features
List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Phonebook List Names. • The UConnect™ system will play the names of all the phonebook entries. •...
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone.
Page 89 Conference Call When two calls are in progress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-Way Calling To initiate three-way calling, press the ’Voice Recogni- tion’...
Page 90: Uconnect™ System Features
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone.
Page 91 If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Emergency and the UConnect™ system will instruct the paired cellular phone to call the emergency num- ber.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Working with Automated Systems This method is designed to be used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated tele- phony system. You can use your UConnect™...
Page 93 • After the Ready prompt and the following beep, say Setup Confirmations. The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it. Phone and Network Status Indicators The UConnect™ system will provide notification to inform you if your cellular phone is in roaming status, has low signal strength, or has a low battery when you are trying to place a phone call.
Page 94: Advanced Phone Connectivity
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Mute-off. Information Service When using AT&T Wireless Service, dialing to phone number #121, you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information.
Page 95 • The UConnect™ system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™...
Page 96: Things You Should Know About Your Uconnect™ System
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your UConnect™ System Voice Recognition (VR) • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you.
Page 97 • It is not recommended to store similar sounding names in the UConnect™ phonebook. • UConnect™ phonebook name tag recognition rate is optimized for the person who stored the name in the phonebook. • You can say O (letter O ) for 0 (zero). 800 must be spoken eight-zero-zero.
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bluetooth Communication Link Cellular phones have been found to occasionally loose connection to the UConnect™ system. When this hap- pens, the connection can generally be re-established by switching the phone off/on. Your cell phone is recom- mended to remain in Bluetooth on mode.
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99...
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101...
Page 102: Seats
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS 10–Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the driver’s front door trim panel. The bottom switch con- trols up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment and the middle switch controls the lumbar adjustment.
Page 103: 8-Way Driver's Power Seat - If Equipped
WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. 8–Way Driver’s Power Seat —...
Page 104: Adjustable Head Restraints
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraint so that the upper edge is as high as practical.
Page 105: Heated Seats - If Equipped
Heated Seats — If Equipped This feature heats the driver, front passenger and second row seats. The controls for the front heated seats are located on the door trim panel next to the power seat switches. Front Heated Seat Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction...
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The controls for the second row heated seats are located on the center console between the seats. Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off.
Page 107: Second Row Manual Seat Recliner - If Equipped
Second Row Manual Seat Recliner — If Equipped The recliner mechanism control is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
Page 108: Second Row Manual Seat Adjuster - If Equipped
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Page 109: Second Row Bench Seating - If Equipped
WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The seat belt might not be properly adjusted and you could be injured. Second Row Bench Seating — If Equipped The second row seats may be used with either or both seatbacks folded forward for additional storage space.
Page 110: Second Row Fold & Tumble Seats - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Be sure there is nothing in front of the second row seat cushion before folding it down. Damage to the seat may occur. Second Row Fold & Tumble Seats — If Equipped The second row seats can be folded and tumbled forward for easy access to the third seat or rear cargo area.
Page 111: Third Row Easy Exit - If Equipped
5. Pull up on the release handle labeled “2” and lift firmly to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. Seat Release Handle UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments.
Page 112 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To fold and tumble the seat forward, follow these steps: 1. Pull up on the seatback release handle “1” located on the back of the seat to fold the seatback down. Release Handle 1 Location 2.
Page 113: Third Row Seating - If Equipped
Third Row Seating — If Equipped The third row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat. Then pull handle located on the seatback and push it forward.
Page 114: Load Floor - If Equipped
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating posi- tion. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat.
Page 115: Plastic Grocery Bag Retainer
Load Floor Panel NOTE: Be sure to reattach the strap to secure the load floor panel when not in use. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all front seats. The floor supports the partial weight of the bagged goods.
Page 116: Driver Memory System - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SYSTEM — IF EQUIPPED If your vehicle is equipped with memory systems, your remote keyless entry transmitter or memory seat buttons on the driver’s door panel can be used to recall the driver’s seat, outside mirrors, adjustable pedals (if equipped) and radio station presets to saved positions.
Page 117 Your vehicle has been delivered with two remote keyless entry transmitters. One or both transmitters can be linked to either memory position. Up to eight remote keyless entry transmitters can be used with your vehicle. The memory seat system can also accommodate up to eight transmitters linked to either of the two stored seat positions or any combination of the two positions.
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Repeat the above steps for the second position using the other driver’s door numbered button and Remote Key- less Entry Transmitter. Each time the SET (S) button and a numbered button are pressed, you erase the old memory and store a new one. To Disable A Transmitter Link, Follow These Steps: 1.
Page 119: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Hood Release Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Next, push to the left the safety catch located under the front edge of the hood, near the center.
Page 120: Lights
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 15 cm (6 inches) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
Page 121: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 15 minutes if a door is left open or the dimmer control is left in the Dome light position.
Page 122: Multi-Function Lever
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Lever The Multi-Function Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and fog lights. The lever is located on the left side of the steering column.
Page 123: Automatic Headlights
Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dim- mer control is in this position. Interior light Defeat (OFF) Rotate the dimmer control to the ex- treme bottom “OFF”...
Page 124: Daytime Running Lights (Canada Only)
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The engine must be running before the head- lights will come ON in the Automatic mode. Daytime Running Lights (Canada Only) The high beam headlights will come on as Daytime Running Lights whenever the ignition switch is on, the headlights are off, and the parking brake is off.
Page 125: Turn Signals
NOTE: The fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals Move the Multi-Function Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Page 126: Windshield Wipers And Washers
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Rotate the end of the control lever to select the desired wiper speed. Windshield Wiper/Washer Control Windshield Washers To use the front washer, pull the lever toward you and...
Page 127: Windshield Wiper Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Windshield Wiper Operation Rotate the end of the lever to the second detent for Low speed wiper operation, or to the third detent for High speed operation Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable.
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the rear wiper. Push the lever forward to initiate the rear wash function in any of the three positions. The washer pump will continue to operate as long as the lever is pressed.
Page 129: Tilt Steering Column
TILT STEERING COLUMN To tilt the column, pull the lever, located behind the turn signal control, toward you and move the steering wheel up or down, as desired. Release the lever to lock the steering wheel firmly in place. Tilt Steering Column Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! Tilting the steering column while the vehicle is...
Page 130: Traction Control Switch - If Equipped
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL SWITCH — IF EQUIPPED The traction control Indicator, located in the instrument cluster, will light up when the Traction Control is in use. To turn the system OFF, press the Traction Control switch located on center console next to the ash tray, until the traction control Indicator in the instrument cluster lights Traction Control Switch...
Page 131: Rear Park Assist System - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • The Traction Control system will make buzzing or clicking sounds when in operation. REAR PARK ASSIST SYSTEM — IF EQUIPPED This system is used to help drivers determine if an obstacle is in the way of the vehicle while it is backing up in addition to the use of inside rearview and outside mirrors.
Page 132 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, other vehicles, obstructions, and blind spots before backing up.
Page 133: Adjustable Pedals - If Equipped
ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position.
Page 134: Electronic Speed Control
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be ad- justed when the system is locked out (“Adjustable Pedal Disabled —...
Page 135: To Activate
Speed Control Switches To Activate: Push the “ON/OFF” button once and the CRUISE indi- cator located near the instrument cluster odometer will illuminate showing the electronic speed control system is on. To turn the system OFF, push the “ON/OFF” button again and the system and indicator will turn off.
Page 136: To Deactivate
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate: A soft tap on the brake pedal, pushing the “CANCEL” button or normal braking while slowing the vehicle will deactivate the speed control without erasing the memory. Pushing the “ON/OFF” button to the OFF position or turning off the ignition erases the speed memory.
Page 137: Overhead Console - If Equipped
Four speed automatic transmissions will experience a downshift to 3rd gear while climbing uphill or descend- ing downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
Page 138: Courtesy/Reading Lights
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door, a rear door or the liftgate is opened.
Page 139: Programming Homelink
WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Press and hold the two outer HomeLink buttons, and release only when the indicator light begins to flash or the EVIC display shows “Channels Cleared” (after 20 seconds). Do not hold the buttons for longer than 30 seconds and do not repeat step one to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons.
Page 141 WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the EVIC display shows “Did Not Train” repeat steps 2–4. 5. Press and hold the just trained HomeLink button and observe the indicator light or the EVIC display. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released.
Page 143: Canadian Programming/Gate Programming
8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the press/hold/release sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming.
Page 144: Using Homelink
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.).
Page 145: Security
Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instruc- tions in this section. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: •...
Page 146: Express Open Feature
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the “OPEN” button rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the “OPEN” button rearward will activate the Express Open Feature, causing the sunroof to open automatically.
Page 147 To close the sunroof, press and hold the “CLOSE” button forward. Again, any release of the button will stop the movement and the sunroof will remain in a partial open condition until the button is pushed forward again. The sunshade can be opened manually. It will also open as the sunroof opens.
Page 148: Wind Buffeting
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 149 Front Power Outlets A third outlet is located on the back of the front center console near the floor, and is also controlled by the ignition switch. A fourth outlet is located on the driver’s side, in the rear cargo area and is also controlled by the ignition switch. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 The outlets include tethered caps labeled with a key or battery symbol indicating the power source.
Page 150: Electrical Outlet Use With Engine Off
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 151: Second Row Seat Cupholders
Second Row Seat Cupholders On vehicles equipped with five passenger seating the second row seat cupholders are located in middle of the seatback armrest. Pull down on the armrest to access the cupholders. Push the armrest up when the cupholders are no longer needed.
Page 152: Rear Cargo Storage Bin - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cargo Storage Bin — If Equipped The storage bin is located in the floor of the rear cargo area. To open lift up on the handle. Rear Storage Bin Retractable Cargo Area Cover — If Equipped To cover the cargo area: 1.
Page 153: Cargo Tie-Down Hooks
WARNING! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment.
Page 154 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
Page 155: Roof Luggage Rack - If Equipped
ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Roof Rack UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Distribute cargo weight evenly on the roof rack crossbars.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To reduce the amount of wind noise when the cross bars are not in use, move both cross bars next to each other towards the rear of the vehicle in the rear most position.
Page 157: Load Leveling System
WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
Page 159 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....162 Base Instrument Cluster ....163 Premium Instrument Cluster .
Page 160 160 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode For MP3 Audio Play) ..... 192 Sales Code RBP—AM & FM Stereo Radio With Cassette Tape Player, CD Player, And Optional CD/DVD Changer Controls .
Page 161: Understanding Your Instrument Panel
Using The PTY (Program Type) Button (If Equipped) ......216 PTY Button Scan ..... 217 PTY Button Seek .
Page 162: Instruments And Controls
162 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS...
Page 163: Base Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 163 BASE INSTRUMENT CLUSTER...
Page 164: Premium Instrument Cluster
164 UNDERSTANDING YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER...
Page 165: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Voltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained.
Page 166 166 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
Page 167 If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
Page 168 168 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD).
Page 169 • The system has been deactivated to prevent damage to the brake system due to overheated brake tem- peratures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the Traction Control Light. This is to prevent overheating of the brake system and is a normal condition.
Page 170 170 UNDERSTANDING YOUR INSTRUMENT PANEL replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button.
Page 171 The Malfunction Indicator Light flashes to alert you to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. 16. High Beam Light This light shows that the headlights are on high beam.
Page 172 172 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Tire Pressure Monitor Warning Light — If Equipped This light will turn on when there is a Low tire pressure condition. The light will remain on until the tire pressure is properly set. The light will also flash if a problem exist with any tire sensor.
Page 173 22. Airbag Light This light turns on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible.
Page 174: Electronic Vehicle Information Center (Evic) - If Equipped
174 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) con- sists of the following: • Vehicle information warning message displays • Tire Pressure Monitor System — If Equipped • Customer programmable features •...
Page 175 • SET INHIBITED DUE TO MOTION (with a single chime) • FOB LINKED (with a single chime) • FOB UNLINKED (with a single chime) • PARK BRAKE ENGAGED (with a single chime) • LOW BRAKE FLUID (with a single chime) •...
Page 176: Customer Programmable Features - If Equipped
176 UNDERSTANDING YOUR INSTRUMENT PANEL • CHANNEL 1, 2, OR 3 TRAINING (with a single chime) • CHANNEL 1, 2, OR 3 TRAINED (with a single chime) • CLEARING CHANNELS • CHANNELS CLEARED • CHANNELS DEFAULTED • DID NOT TRAIN •...
Page 177 Park Assist System? ON/OFF When this feature is selected the system scans for objects behind the vehicle using four sensors located in the rear bumper. Objects can be detected from up to 71 inches (180 cm). Pressing the “STEP” button while in this display will disable/enable the Rear Park Assist System.
Page 178 178 UNDERSTANDING YOUR INSTRUMENT PANEL keyless entry unlock button. Pressing the STEP button when in this display will select DRIVER’S DOOR 1ST or ALL DOORS. Remote Linked To Memory? (Available with Memory Seat Only) When this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the remote keyless entry “Unlock”...
Page 179 turn off when the wipers are turned off if they were turned on in this way. Pressing the STEP button when in this display will select “Yes” or “No.” NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights”...
Page 180: Compass Display - If Equipped
180 UNDERSTANDING YOUR INSTRUMENT PANEL driver can more easily exit the vehicle. The seat will return to the memorized seat location (if REMOTE LINK TO MEMORY is set to YES) when the remote keyless entry transmitter is used to unlock the door. Pressing the STEP button when in this display will select “Yes”...
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 181 Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
Page 182: Mini-Trip Functions - If Equipped
182 UNDERSTANDING YOUR INSTRUMENT PANEL To set the variance: Turn the ignition switch ON and set the display to Compass. Press the RESET button for approximately 5 seconds but no more than 10 seconds. The “COMPASS VARIANCE” message and the last vari- ance zone number will be displayed.
Page 183: Electronic Digital Clock
ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position and the time button is pressed. When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained.
Page 184: Radio Operation
184 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 185 Program Type Radio Display Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
Page 186 186 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed.
Page 187: Cd Player Operation
You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 188 188 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept only 4–3/4 inch (12cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
Page 189: Cd/Dvd Changer Operation
RND — Random Play Press the RND button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
Page 190 190 UNDERSTANDING YOUR INSTRUMENT PANEL When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: •...
Page 191 MPEG Specifi- Sampling Fre- cation quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 192: Operation Instructions
192 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode For MP3 Audio Play) SEEK Button (CD Mode For MP3 Play) Pressing the SEEK + button plays the next MP3 File. Pressing the SEEK button plays the beginning of the MP3 file.
Page 193: Sales Code Rbp-Am & Fm Stereo Radio With Cassette Tape Player, Cd Player, And Optional Cd/Dvd Changer Controls
Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES ) (If Equipped) Refer to 6 Disc CD/DVD Changer (RDV) section of the Owner’s Manual. UNDERSTANDING YOUR INSTRUMENT PANEL 193 SALES CODE RBP—AM &...
Page 194: Radio Operation
194 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control to the right to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 195 Program Type Radio Display Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
Page 196 196 UNDERSTANDING YOUR INSTRUMENT PANEL Scan Press and release the SCAN button to search for the next station in either the AM or FM mode. The radio will pause for 5 seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time.
Page 197 SET 1 will now show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory.
Page 198: Tape Player Operation
198 UNDERSTANDING YOUR INSTRUMENT PANEL Tape Player Operation Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
Page 199 Rewind — RW Press the RW button down momentarily to reverse the tape direction. The tape will rewind until the button is pressed again or until the beginning of the tape is reached. At the beginning of the tape, the tape will play in the opposite direction.
Page 200: Cd Player Operation
200 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio off, the display will show CD and the time of day will be displayed.
Page 201: Cd/Dvd Changer Operation - If Equipped
FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW (Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play.
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL Disc Up/Program Button 1 Press the DISC (button 1) button to play the next avail- able disc. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the selections on the currently playing compact disc in random order to provide an interesting change of pace.
Page 203: Disc Cd/Dvd Changer (Rdv) - If Equipped
6 DISC CD/DVD CHANGER (RDV) — IF EQUIPPED The Rear Seat Audio/Video System allows passengers to listen to a CD or DVD from the 6 disc CD/DVD changer through wireless headphones, while the front seat pas- sengers listen to either AM/FM, Cassette or CDs from the radio speakers.
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL To insert disc(s) into the changer, follow the instructions shown: 1. On vehicles equipped with the premium version, select and press any numbered button without an illumi- nated light above it. 2. Gently insert the disc with the label facing up while the light below the loading slot is illuminated.
Page 205: Eject (Ejt) Button
• If you insert a disc with the ignition ON and the radio OFF, the DVD will automatically be pulled into the DVD changer and the display will show the time of day. • It is recommended to label home made burned discs with a permanent marker instead of adhesive labels.
Page 206 206 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Buttons 1. Headphone Transmitter 2. Menu Up/Next Track/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 11. Program Up - Next Disc 12.
Page 207 Remote Control Buttons 17. Enter 18. Light Headphone Transmitter Button (1) After a disc is inserted into the DVD changer, both the headphone transmitter button (1) on the remote control and the power button on the headphones must be turned ON before sound can be heard from the headphones.
Page 208 208 UNDERSTANDING YOUR INSTRUMENT PANEL PAUSE/PLAY Button (6) This button only functions in DVD video mode. Press this button once to pause the video, press a second time to play the video. MUTE Button (7) No function. DISP Button (8) This button only functions in DVD video mode.
Page 209 NEXT/PREV Buttons (2, 15) Press the up arrow or the NEXT button for the next chapter or track on the disc. Press the down arrow or PREV button to return to the beginning of the current chapter or track. Press the down arrow or PREV button twice within two seconds to return to the previous chapter or track.
Page 210: Operating Instructions - Video Screen
210 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Video Screen Push up on the release button to lower the video screen. Lowering Video Screen 1. Screen Width Button Changes the width of the screen picture. 2. Enter Button This button will enter the selection from the on-screen menu.
Page 211: Operating Instructions - Headphones
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Operating Instructions — Headphones Video Screen Controls Headphone Controls 1. Power Button 2. Volume Control 3. Power Indicator...
Page 212 212 UNDERSTANDING YOUR INSTRUMENT PANEL Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the head- phone earpiece to indicate the headphones are ON. NOTE: • The headphones will turn off automatically in ap- proximately 3 minutes if they lose the signal form the system or when the radio or rear audio/video system is turned off.
Page 213: Operating Instructions - Mp3 Player, Portable Walkman
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 214: Satellite Radio - If Equipped
214 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To operate a video game unit a DC to AC adapter may be required, plug the adapter into any power outlet. Follow the manufactures instructions for the correct colors when connecting the RCA cables. NOTE: MP3 player’s, video game systems, camcorders connected to the RCA jacks and CD’s or DVD’s inserted into the CD/DVD changer can be heard through the...
Page 215: Selecting Satellite Mode In Rbb, Rah And Rbk Radios
ESN/SID Access With RBB, RAH and RBK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the Tape Eject or CD Eject (depend- ing on the radio type) and Time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed.
Page 216: Selecting A Channel
216 UNDERSTANDING YOUR INSTRUMENT PANEL • The current channel number will then be displayed until an action occurs. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel.
Page 217: Pty Button Scan
PTY Button SCAN When the desired program type is obtained, press the SCAN button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type. Press the SCAN button a second time to stop the search.
Page 218: Remote Sound System Controls
218 UNDERSTANDING YOUR INSTRUMENT PANEL • Placing objects over or too close to the antenna can cause signal blockage. REMOTE SOUND SYSTEM CONTROLS The remote sound system controls are located on the rear surface of the steering wheel at the 3 and 9 o’clock positions.
Page 219: Cd Player
The button in the center of the left hand switch has no function in this mode. CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play.
Page 220: Electrical Disturbances
220 UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal.
Page 221: Cd/Dvd Disc Maintenance
5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
Page 222: Radio Operation And Cellular Phones
222 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
Page 223: Climate Controls
To replace the navigation map DVD lift the storage bin cover and liner in the rear cargo area, press the eject button and the disc will eject. Gently insert the new disc into the DVD unit with the label facing up. The disc will automatically be pulled into the DVD unit.
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL second time the indicator light turns off, the blower will turn off and the system will be positioned in the recircu- lation mode. Blower Control The Blower controls the amount of air delivered to the passenger compartment. There are four blower speeds.
Page 225: Mode Control
Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. UNDERSTANDING YOUR INSTRUMENT PANEL 225 Panel Mode Panel Outlets...
Page 226 226 UNDERSTANDING YOUR INSTRUMENT PANEL Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets.
Page 227 NOTE: In many temperature lever positions, the bi- level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets. Floor Mode Floor Outlets UNDERSTANDING YOUR INSTRUMENT PANEL 227 Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.
Page 228: Manual Air Conditioning Operation
228 UNDERSTANDING YOUR INSTRUMENT PANEL Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keep- ing the windshield clear. Defrost Mode Defrost Outlets Air comes from the windshield and side window demist outlets.
Page 229 Cool dehumidified air comes through the outlets selected by the Mode Control. To turn off the air conditioning, press the A/C button a second time. The indicator light will turn off. NOTE: • The compressor will not engage until the engine has been running for a few seconds.
Page 230 230 UNDERSTANDING YOUR INSTRUMENT PANEL • In cold weather, use of the Recirculation mode may lead to excessive window fogging. The Recirculation mode is not allowed in the Mix and Defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected.
Page 231 • Press the recirculation button until the indicator light remains lit. • The selection will be stored when the ignition switch is turned OFF or if the “POWER” button is pressed. If the recirculation indicator light is lit, the recirculation mode will not reset when the engine is started.
Page 232: Dual-Zone Automatic Temperature Control
232 UNDERSTANDING YOUR INSTRUMENT PANEL • The selection will be stored when the ignition switch is turned OFF or if the “POWER” button is pressed. If the recirculation indicator light is lit, the recirculation mode is enabled. If the recirculation indicator light is not lit, the recirculation mode is OFF.
Page 233 To operate the system, press either the AUTO HI or AUTO LO buttons. The system now automatically regulates the heating and air conditioning system includ- ing blower speed, outlet air temperature, and airflow distribution through the various outlets within the in- strument panel.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL This feature may be disabled using the following proce- dure: • Press and hold the Heated Rear Window and Auto LO buttons for 5 seconds. • The “DELAY” symbol will flash to indicate that the feature as been disabled.
Page 235 Manual Operation This system offers a full complement of manual override features. The indicator light in both the AUTO HI or AUTO LO buttons will turn off when the system is being used in the manual mode. The fan speed, airflow distribution, and outside air/recirculated air can be manually adjusted.
Page 236 236 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Panel Outlets Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the knob up, down, left, or right will direct the air accordingly.
Page 237 UNDERSTANDING YOUR INSTRUMENT PANEL 237 Air comes from both the instrument panel outlets and Bi-Level Mode floor outlets. A slight amount of air is also directed through the defrost and side window demister outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 238 238 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Floor Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Outlets Air comes from the floor, defrost and side window demist outlets.
Page 239 Defrost Mode Defrost Outlets Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. If a fog or mist on the windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum.
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control When the outside air contains smoke, odors, high humidity, or if rapid cooling is desired you may wish to recirculate interior air by pressing the recirculation button. The recircu- lation mode should only be used temporarily. The recir- culate symbol will illuminate in the display when this button is selected.
Page 241 The recirculation control is now programmed so that the recirculation mode will not reset to the outside air mode when the engine is restarted. The recirculation program- ming can be changed back by repeating this procedure. Rear Fan Operation To operate the rear fan, press the REAR button. The first time this button is pressed the REAR AUTO display will illuminate indicating that the rear fan speed is automatically controlled.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation To insure the best possible heater and defroster perfor- mance, make sure the engine cooling system is function- ing properly and the proper amount, type, and concen- tration of coolant is used. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection.
Page 243: Electric Rear Window Defroster
A/C Air Filter The climate control system filters out dust, pollen and some odors from the air. Strong odors can not be totally filtered out. Refer to section 7 “Air Conditioning” for filter replacement instructions. Outside Temperature Display The outside temperature can be shown in the ATC display by pressing the OUTSIDE TEMP button.
Page 245: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 248 Normal Starting ..... . 248 Engine Block Heater —...
Page 246 246 STARTING AND OPERATING Tire Markings ......263 Tire Identification Number (TIN) ..267 Tire Loading And Tire Pressure .
Page 247 MMT In Gasoline ..... 288 Materials Added To Fuel ....289 Fuel System Cautions .
Page 248: Starting Procedures
248 STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather;...
Page 249 WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Un- burned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 250: Engine Block Heater - If Equipped
250 STARTING AND OPERATING the floor. Release the accelerator pedal and the key once the engine is running smoothly. Do not overspeed en- gine. If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the “NORMAL STARTING”...
Page 251: Automatic Transmission
AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Page 252: Automatic Transmission Ignition Interlock System
252 STARTING AND OPERATING Automatic Transmission Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ACCESSORY or ON position.
Page 253 NOTE: Even if the transmission can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equip- ment to determine if the problem could recur. If the transmission cannot be reset, dealer service is required.
Page 254: Autostick
254 STARTING AND OPERATING AUTOSTICK Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
Page 255: All Wheel Drive - If Equipped
• You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h). • The transmission will automatically downshift to first gear when coming to a stop. •...
Page 256: Parking Brake
256 STARTING AND OPERATING CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling. PARKING BRAKE When the parking brake is applied with the ignition switch on, the brake light in the instrument cluster will turn on.
Page 257 When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade.
Page 258: Brake System
258 STARTING AND OPERATING BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
Page 259 WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 260 260 STARTING AND OPERATING When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system per- forming its self check cycle to ensure that the ABS system is working properly.
Page 261: Power Steering
POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason, the power assist is interrupted, it will still be possible to steer your vehicle.
Page 262: Traction Control - If Equipped
262 STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The Traction Control System reduces wheel slip and maintains traction at the driving (front) wheels. The system reduces wheel slip by engaging the brake on the wheel that is losing traction (spinning). The system will operate at speeds below 35 mph (56 km/h).
Page 263: Tire Safety Information
NOTE: • The Traction Control system will make buzzing or clicking sounds when in operation. • Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control indicator located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition.
Page 264 264 STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 265 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 266 266 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 267: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 268: Tire Loading And Tire Pressure
268 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B”...
Page 269 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle STARTING AND OPERATING 269 4) the cold tire inflation pressures for the front, rear and spare tires.
Page 270 270 STARTING AND OPERATING lbs.” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds”...
Page 271 STARTING AND OPERATING 271...
Page 272: Tires-General Information
272 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 273: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 274 274 STARTING AND OPERATING The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation.
Page 275 Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits.
Page 276: Radial-Ply Tires
276 STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 277: Limited Use Spare - If Equipped
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the...
Page 278: Tire Spinning
278 STARTING AND OPERATING WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly.
Page 279: Replacement Tires
These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
Page 280: Alignment And Balance
280 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 281: All Wheel Drive (Awd) - If Equipped
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. ALL WHEEL DRIVE (AWD) — IF EQUIPPED CAUTION! All Wheel Drive (AWD) vehicles must have the same size and type tires on all wheel positions.
Page 282: 1,2,3, Or 4 Tire(S) Low Pressure
282 STARTING AND OPERATING 1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pressure levels of 26 psi [1.79 bars] (179 kPa) or less detected in one or more tires. Inspect all tires for proper inflation pressure, once the proper tire pressure has been set, the TPM system warning will reset automatically when the vehicle has been driven for at least 2 minutes at or above 20 mph (32 km/h).
Page 283 CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sen- sor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Page 284: General Information
284 STARTING AND OPERATING General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 285: Snow Tires
CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage.
Page 286: Tire Rotation Recommendations
286 STARTING AND OPERATING Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions.
Page 287: Fuel Requirements
STARTING AND OPERATING 287 Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 288: Gasoline/Oxygenate Blends
288 STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle.
Page 289: Materials Added To Fuel
Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives are not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel.
Page 290: Carbon Monoxide Warnings
290 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 291 CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! To avoid fuel spillage and overfilling, do not “top off”...
Page 292: Vehicle Loading
292 STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is shown in the charts that follow. This information should be used for passenger and luggage loading as indicated. If the seatbacks are folded for carrying cargo, do not exceed the specified GVWR and GAWR.
Page 293: Overloading
WARNING! Because the front wheels drive and steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory...
Page 294: Trailer Towing
294 STARTING AND OPERATING A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded. Example Only Empty Weight Load (Including driver, pass- sengers and cargo) Total GAWR TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
Page 295: Towing Requirements
To maintain warranty coverage, follow the requirements and recommendations in this manual concerning ve- hicles used for trailer towing. Perform maintenance services as prescribed in the main- tenance schedules manual. When your vehicle is used for trailer towing, never exceed the gross axle weight rating (GAWR) by the addition of: •...
Page 296 296 STARTING AND OPERATING • Do not attempt to tow a trailer while using a compact spare tire. • Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety. •...
Page 297 MAXIMUM TRAILER WEIGHT TRAVEL CONDITION Trailer Frontal Area Not To Exceed 40 Square Feet (3.72 Square Meters) 3.5/3.8L ENGINES MAX. COMBINED WEIGHT OF VEHICLE AND TRAILER NOT TO EXCEED 8,600 lbs (3900 UP TO 2 PERSONS & 3,500 lbs (1600 kg) LUGGAGE 3 TO 4 PERSONS &...
Page 298: Recreational Towing (Behind Motorhome, Etc.)
298 STARTING AND OPERATING WARNING! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the...
Page 299: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....300 If Your Engine Overheats ....301 Jacking And Tire Changing .
Page 300: Hazard Warning Flasher
300 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the center air outlets. Hazard Flasher Switch To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer- gency.
Page 301: If Your Engine Overheats
IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed.
Page 302: Jacking And Tire Changing
302 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual.
Page 303: Jack Location
Jack Location Five Passenger Seating The jack and jack-handle are stowed in the rear storage bin located behind the second row bench seat. Pull up on the storage bin cover to access the jack and jack tools. Jack Location WHAT TO DO IN EMERGENCIES 303 Remove the scissors jack and jack handle by rotating the small wing nut to the left.
Page 304: Spare Tire Stowage
304 WHAT TO DO IN EMERGENCIES Six Passenger Seating The jack and jack-handle are stowed in the rear storage bin located in the rear cargo floor. Pull up on the storage bin cover and liner to access the jack and jack tools. Jack Location Spare Tire Stowage Five Passenger Seating...
Page 305: Preparations For Jacking
Lowering Spare Tire Spare Tire Removal Fit the jack-handle over the drive nut. Rotate the nut to the left until the spare is on the ground with enough slack cable to allow you to pull the tire out from under the vehicle.
Page 306: Jacking Instructions
306 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. •...
Page 307 Jack Engagement Locations 5. These locations are on the sill flange on the underside of the body. The jack is to be located, engaging the flanges, 20 cm (8 inches) inward from the edge of the wheel opening closest to the wheel to be changed. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described WHAT TO DO IN EMERGENCIES 307...
Page 308 308 WHAT TO DO IN EMERGENCIES 7. Remove the wheel lug nuts, for vehicles with wheel covers, remove the cover from the wheel by hand. Do not pry the wheel cover off. Then pull the wheel off the hub. 8. Install the spare wheel, for vehicles with wheel covers, align the notch in the wheel cover with the valve stem on the wheel.
Page 309: Jump-Starting Procedures If Battery Is Low
• Turn the wheel so that the valve-stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. • For convenience in checking the spare tire inflation, stow with the valve-stem toward the rear of the vehicle.
Page 310 310 WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmis- sion cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 311: Driving On Slippery Surfaces
5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery.
Page 312: Freeing A Stuck Vehicle
312 WHAT TO DO IN EMERGENCIES 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion.
Page 313: Towing A Disabled Vehicle
TOWING A DISABLED VEHICLE With Ignition Key Front Wheel Drive Your vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be traveled must not exceed 100 miles (160 km), the towing speed must not exceed 44 mph (72 km/h), and both front and rear wheels must be on the ground.
Page 314: Without The Ignition Key
314 WHAT TO DO IN EMERGENCIES All Transmissions CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front.
Page 315: Towing This Vehicle Behind Another Vehicle With A Tow Dolley
WHAT TO DO IN EMERGENCIES 315 TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A TOW DOLLEY The manufacturer does not recommend that you tow an All-Wheel Drive (AWD) or front wheel drive vehicle on a tow dolley. Vehicle damage may occur.
Page 317: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 3.5L Engines ......320 3.8L Engines ......321 Onboard Diagnostic System —...
Page 318 318 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance ... . . 335 Power Steering — Fluid Check ... . 336 Front & Rear Suspension Ball Joints ..337 Steering Shaft Seal .
Page 319 High Intensity Discharge Headlights (HID) — If Equipped ......365 Front Park/Turn Signal And Sidemarker Lights .
Page 320: 3.5L Engines
320 MAINTAINING YOUR VEHICLE 3.5L ENGINES Engine Compartment 3.5L Engines...
Page 321: L Engines
MAINTAINING YOUR VEHICLE 321 3.8L ENGINES Engine Compartment 3.8L Engines...
Page 322: Onboard Diagnostic System - Obd Ii
322 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 323: Loose Fuel Filler Cap Message
Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose, improperly installed, or damaged. A loose fuel filler cap message will be displayed in the instrument cluster. Tighten the gas cap until a clicking sound is heard.
Page 324 324 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key actuated test which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2.
Page 325: Replacement Parts
Regardless of whether your vehicle’s OBD system is ready or not ready, if the MIL symbol is illuminated during normal vehicle operation, you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running.
Page 326: Maintenance Procedures
326 MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 327 Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. MAINTAINING YOUR VEHICLE 327 Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you.
Page 328 328 MAINTAINING YOUR VEHICLE NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the Maintenance Schedules section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule A of the Mainte- nance Schedules section of this manual.
Page 329 • SAE 10W-30 engine oil is preferred. SAE 5W-30 engine oil is allowed during cold weather only to improve cold weather starting. Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used.
Page 330: Engine Oil Filter
330 MAINTAINING YOUR VEHICLE Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recom- mended SAE viscosity grade.
Page 331: Spark Plugs
Belts should be inspected for evidence of cuts, cracks, or glazing, and replaced if there is indication of damage which could result in belt failure. Low generator belt tension can cause battery failure. Also check belt routing to make sure there is no interfer- ence between the belts and other engine components.
Page 332: Fuel Filter
332 MAINTAINING YOUR VEHICLE Fuel Filter A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause hard starting. Should an excessive amount of dirt accumulate in the fuel tank, filter replacement may be necessary. See your local dealer for service.
Page 333: Maintenance-Free Battery
WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
Page 334 334 MAINTAINING YOUR VEHICLE WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 335: Air Conditioner Maintenance
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time.
Page 336: Power Steering - Fluid Check
336 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 337: Front & Rear Suspension Ball Joints
WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
Page 338: Body Lubrication
338 MAINTAINING YOUR VEHICLE Continued operation could result in failure of the univer- sal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly. Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear.
Page 339: Windshield And Rear Window Washers
Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
Page 340: Cooling System
340 MAINTAINING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
Page 341 Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
Page 342 342 MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 343 The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.
Page 344 344 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground.
Page 345: Hoses And Vacuum/Vapor Harnesses
• Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks.
Page 346: Brakes
346 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure.
Page 347: Master Cylinder - Abs Brakes Brake Fluid Level Check
Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to facilitate the assembly of hoses to couplings.
Page 348 348 MAINTAINING YOUR VEHICLE Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system.
Page 349: Fuel System Hoses
CAUTION! Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be damaged causing partial or complete brake failure. Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and quick connect fittings which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline.
Page 350 350 MAINTAINING YOUR VEHICLE Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
Page 351 3. Fully apply parking brake. 4. Place the gear selector momentarily in each gear position ending with the lever in P (PARK). Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transmission. 5. Remove the dipstick and determine if the fluid is hot or warm.
Page 352: All Wheel Drive (Awd) - If Equipped
352 MAINTAINING YOUR VEHICLE Severe Usage (fluid and filter) — Refer to Maintenance Schedule “B” Severe Usage is defined as: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for Mainte- nance Schedules.
Page 353 Overrunning Clutch The fill plug is located on the side of the overrunning clutch housing. The fluid should be maintained at a level even with the bottom of the fill plug hole when the vehicle is parked on a level surface. If it becomes neces- sary to add or replace the fluid, use only the manufac- turers recommended transmission fluid, refer to Recom- mended Fluids, Lubricants and Genuine Parts for correct...
Page 354: Front And Rear Wheel Bearings
354 MAINTAINING YOUR VEHICLE NOTE: Refer to Section 8 of this manual for Mainte- nance Schedules. Front And Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these compo- nents. Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 355 Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, wash it as soon as possible. •...
Page 356 356 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibil- ity of the owner.
Page 357 Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean.
Page 358: Cleaning The Center Console Cup Holders
358 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
Page 359: Integrated Power Module (Ipm)
INTEGRATED POWER MODULE (IPM) Integrated Power Module (IPM) An Integrated Power Module is located in the engine compartment near the battery. This center contains maxi fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover. MAINTAINING YOUR VEHICLE 359 Cavity Maxi Fuse...
Page 360 360 MAINTAINING YOUR VEHICLE Cavity Maxi Fuse Spare 40 Amp Headlight Washer, Power Green Liftgate Spare 40 Amp Radiator Fan 1 Green Spare 40 Amp Anti-Lock Brake System Green (ABS) Module 40 Amp Driver Door Node Green 40 Amp Passenger Door Node Green 40 Amp Front Blower...
Page 361 Cavity Mini Fuse Description Spare Spare 20 Amp Yel- Electronic Automatic Transaxle (EATX) Solenoid 25 Amp Natural 20 Amp Yel- Fuel Pump 20 Amp Yel- A/C Clutch, MTV 25 Amp Rear Heated Seats Natural 10 Amp Red Anti-Lock Brake System (ABS) Ignition Run 20 Amp Yel- Passenger Door...
Page 362: Vehicle Storage
362 MAINTAINING YOUR VEHICLE CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 363: Replacement Light Bulbs
REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Center & Rear Reading Lights ....578 Front Door Courtesy Light ....578 Liftgate Light(s).
Page 364: Bulb Replacement
364 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Standard Quad Headlights 1. Remove the two screws securing the headlight mod- ule to the vehicle and pull the headlight module forward away from the vehicle, disengaging the assembly from the lower attachment clip. 2.
Page 365: High Intensity Discharge Headlights (Hid) - If Equipped
High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch off and the key removed. Because of this, you should not attempt to service a headlight bulb yourself.
Page 366: Front Park/Turn Signal And Sidemarker Lights
366 MAINTAINING YOUR VEHICLE Front Park/Turn Signal and Sidemarker Lights 1. Remove the two screws securing the headlight mod- ule to the vehicle and pull the headlight module forward away from the vehicle, disengaging the assembly from the lower attachment clip. 2.
Page 367: Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights
Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two tail light assembly screws and rotate the assembly outward to remove the ball stud form the attaching grommet. MAINTAINING YOUR VEHICLE 367 3.
Page 368: Fluids And Capacities
368 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (approximate) 89 Octane Engine Oil-With Filter 3.5 Liter Engines (SAE 10W-30, API Certified) 3.8 Liter Engines (SAE 5W-20, API Certified) Cooling System * 3.5 Liter Engines (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula or equivalent) 3.8 Liter Engines (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.
Page 369: Recommended Fluids, Lubricants And Genuine Parts
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent 3.5 Liter Engine Oil Use API Certified SAE 10W-30 engine oil, refer to oil viscosity chart for cor- rect SAE grade meeting DaimlerChrysler Material Standard MS-6395.
Page 370: Chassis
370 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission AWD Power Transfer Unit AWD Overrunning Clutch AWD Rear Carrier Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar ATF+4 Automatic Transmission Fluid or equivalent. Mopar Gear Lubricant 75W-90 or equivalent. Mopar ATF+4 Automatic Transmission Fluid or equivalent.
Page 371 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..372 Maintenance Schedules ....372 Schedule “B” ......375 Schedule “A”...
Page 372: Emission Control System Maintenance
372 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 373 • Taxi, police, or delivery service (commercial ser- vice). • Off-road or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the Maintenance Schedules section of this manual.
Page 374 374 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant bottle, brake master cylinder and transmission, add as needed. •...
Page 375: Schedule "B
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
Page 376 376 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive (AWD) power transfer unit fluid.
Page 377 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Change the All Wheel Drive (AWD) power transfer...
Page 378 378 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive power transfer unit fluid.
Page 379 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front &...
Page 380 380 SCHEDULE “B” Miles (Kilometers) Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrun- ning clutch and rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter.
Page 381 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Replace the spark plugs. Inspect the tie rod ends and boot seals. (Front &...
Page 382 382 SCHEDULE “B” Miles (Kilometers) Change the All Wheel Drive (AWD) overrun- ning clutch and rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter. 75, 000 78, 000 81, 000 84, 000 (120 000) (125 000) (130 000) (134 000) (139 000) 87, 000 90, 000 (144 000)
Page 383 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter * Replace engine timing belt. Change the All Wheel Drive (AWD) power transfer unit fluid.
Page 384 384 SCHEDULE “B” Miles (Kilometers) Flush and replace the engine coolant at 60 months or 100,000 miles. Replace the air conditioning filter. 93, 000 96, 000 99, 000 100, 000 (149 000) (154 000) (158 000) (160 000) (163 000) 102, 000 105, 000 (168 000)
Page 385 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Inspect the serpentine drive belt, replace if neces-...
Page 386 386 SCHEDULE “B” * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected.
Page 387: Schedule "A
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front &...
Page 388 388 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front &...
Page 389 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check and replace the PCV valve , if necessary.* Inspect the serpentine drive belt, replace if neces-...
Page 390 390 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace engine timing belt. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary.
Page 391 * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts.
Page 393: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......394 Prepare For The Appointment .
Page 394: Suggestions For Obtaining Service For Your Vehicle
394 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 395 Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s dealers have the facilities, factory-trained...
Page 396 396 IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni-...
Page 397: Warranty Information
The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in...
Page 398 398 IF YOU NEED CONSUMER ASSISTANCE U.S. ONLY...
Page 399: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 400: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 401: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 402: Temperature Grades
402 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade is based on braking (straight- ahead) traction tests and does not include cornering (turning) performance. Temperature Grades The temperature grades are A (highest), B, and C, repre- senting the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 403 INDEX...
Page 404 404 INDEX Adding Fuel ......290 Adding Washer Fluid ....128,339 Additives, Fuel .
Page 405 Selection Of Lubricant ....349,370 Shifting ......253 Special Additives .
Page 406 406 INDEX Car Washes ......355 Carbon Monoxide Warning ....290 Cargo Area Cover .
Page 407 Adding Coolant (Antifreeze) ....342 Coolant Capacity ..... . 368 Coolant Level .
Page 408 408 INDEX DVD Player ......203 Electric Remote Mirrors ....78 Electrical Power Outlets .
Page 409 Filters Air Cleaner ......331 Air Conditioning ....243,336 Automatic Transaxle .
Page 410 410 INDEX Garage Door Opener ..... 138 Gas Cap ......290,323 Gasoline .
Page 411 Ignition Key ....... . . 11 Illuminated Entry ......15 Immobilizer .
Page 412 412 INDEX Anti-Lock ......166 Automatic Headlights ....123 Back-Up .
Page 413 Capacities ......293 Tires ....... 268 Locks Door .
Page 414 414 INDEX Occupant Restraints ..... . . 32 Octane Rating, Gasoline ....287 Odometer .
Page 415 Mirrors ......78 Outlet ......148 Seats .
Page 416 416 INDEX Restraint, Head ......104 Restraints, Child ..... . . 59,65 Restraints, Infant .
Page 417 Security Alarm (Theft Alarm) ....25 Selection of Coolant ....341,369 Sentry Key .
Page 418 418 INDEX System, Navigation ..... . 222 Tachometer ......169 Tape Player .
Page 419 Tread Wear Indicators ....278 Towing ....... 294 Disabled Vehicle .
Page 420 420 INDEX Vehicle Certification Label ....292 Vehicle Identification Number ....6 Vehicle Loading .

Chrysler 2005 Pacifica Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2005 Pacifica

Summary of Contents for Chrysler 2005 Pacifica