Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Neilsen CT2308
Summary of Contents for Neilsen CT2308
- Page 1 HVLP AIR SPRAY GUN KIT WITH REGULATOR CT2308 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: HVLP AIR SPRAY GUN KIT WITH REGULATOR Model: CT2308 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 12100, EN 1953 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. - Page 3 1. SAFETY WARNINGS SYMBOLS In this manual and/or on the machine the following symbols are used: Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual. Wear hearing protection. Wear safety goggles.
-
Page 4: Specification
DO NOT point spray gun at yourself, other persons or animals. DO NOT direct air from the air hose at yourself, other persons or animals. DO NOT carry the spray gun by the hose, or yank the hose from the air supply. ... -
Page 5: Operation
To overcome this, connect a leader hose to the spray gun. A quick change coupling may then be used to connect the leader hose to the air line recoil hose (Fig.A and Fig.B). Fig.B Fig.A 4. OPERATION Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. - Page 6 Note: To prevent damage to the passages, do not use metal objects to clean the Nozzle and Fluid Tip. 5. Clean inside of Spray Gun by pouring warm soapy water into the Fluid Inlet, then run a flexible brush through the passage between the Fluid Inlet and Nozzle opening. 6.
- Page 7 8. Fully depress the Trigger. 9. Turn the Fluid Knob clockwise until it reaches a natural stopping point. 10. Release the trigger. 11. Tighten Collar on Fluid Knob to lock fluid adjustment settings. Air Adjustment 12. Attach Spray Gun to spray gun regulator. Use spray gun regulator to measure airflow PSI.
- Page 8 Fan Direction 16. To change the direction of the fan from horizontal to vertical, loosen the Lock Ring and turn the Nozzle 90° . 17. After the adjustment, tighten the Lock Ring by hand. Spraying Technique IMPORTANT: Proper spraying technique is ESSENTIAL to achieve good results. 1.
- Page 9 When finished with the stroke, release the Trigger while still moving the Spray Gun - see Figure O. Doing this will produce a smoother finish. Do not stop moving the Spray Gun while spraying. If the Spray Gun stops even briefly while spraying the paint will build up and run down the workpiece.
-
Page 10: Maintenance
Note: Do not immerse Spray Gun Body in solvent. Do not allow solvent to enter the air inlet. 6. Remove Nozzle by hand and soak it in solvent until it is clean. Use brush to remove any paint. Note: To prevent damage to the passages, do not use metal objects to clean the Nozzle. 7. -
Page 11: General Troubleshooting Chart
6. TROUBLESHOOTING Spray pattern diagnosis Problem Possible Causes Likely Solutions 1. Open Pattern Knob more. 1. Pattern Knob partially closed. 2. Thin paint according to the manufacturer's Heavy center 2. The paint is too thick. instructions. pattern 3. The air pressure is too low. 3. - Page 12 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...