Related Manuals for Neilsen CSP0006
Summary of Contents for Neilsen CSP0006
- Page 1 50L 12V ATV SPOT / BROADCAST SPRAYER CSP0006 100L 12V ATV SPOT / BROADCAST SPRAYER CSP0007 ORIGINAL INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS PRODUCT.
-
Page 2: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY We CANNON TOOLS LTD 20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K. Declare that the following machine complies with the appropriate basic safety and health requirements of the EC Directive based on its design and type, as brought into circulation by us. -
Page 3: Specifications
1. SPECIFICATIONS CSP0006 Model CSP0007 Volts DC12V DC12V Amps 3.0A 3.0A Max. AMPS 4.0A 4.0A Open flow 3.8LPM/1.0GPM 3.8LPM/1.0GPM Tank capacity 100L Pressure setting 80PSI/5.5Bar 80PSI/5.5Bar Before using any chemical, check to ensure the chemical is compatible with all materials in the system. -
Page 4: Electrical Connection Safety
• Broadcast nozzle down. Make sure broadcast nozzle is oriented to spray straight down before starting the sprayer. An incorrectly positioned broadcast nozzle may spray chemicals on you or others. • Clear area/post. ALWAYS keep the work area clear of people and pets. POST warning notices to restrict access by the public for the period recommended on chemical label. -
Page 5: Atv Vehicle Handling Safety
ATV VEHICLE HANDLING SAFETY: WARNING: Serious injury can occur if the ATV on which the sprayer is mounted is driven unsafely. 1. Less stable. Be aware that all vehicle handling will be affected with the filled sprayer attached. See your ATV’s warning label for the hazards associated with driving: a) Too fast b) On paved surfaces... - Page 6 • However, WE RECOMMEND THAT THE SPRAYER NOT BE USED FOR OTHER PURPOSES ONCE IT HAS ALREADY BEEN USED FOR SPRAYING PESTICIDES. Any agents will leave some residual in the tank liner or sprayer components, even after the sprayer has been properly cleaned. These residual agents can have unexpected effects on future uses.
- Page 7 Pressure gauge (Optional) Clearly display the pressure valve,easy to adjust the pressure. 6 nozzle spray 5. ASSEMBLY Fasten the two lance clips to the sprayer tank with the two screws • supplied. Press the rubber washer onto the drain pipe, screw on the drain cap. •...
- Page 8 • Push the hose onto the hose barb on the spray gun. • Slide the hose clamp around the hose barb and tighten. Attach the sprayer to the vehicle • Sprayer must be installed at the levels of ATV car rack. The installation must use the special water tank fixed machine.
-
Page 9: Operation And Use
6. PREPARATION Preparation • Ensure the sprayer is securely attached to the vehicle. • Ensure the sprayer has been thoroughly flushed and drained of all residual agents from prior uses. • Clean the suction strainer of any agents residue. It is important to clean the suction strainer before each use to ensure it is not clogged and to prevent residual agents from contaminating sprayer contents. - Page 10 nozzle can change shape of the nozzle jet. In the condition of using single spray superfine atomizing nozzle will cause the pressure exceeds the water pump setting pressure, as a result, the water pump pressure switch continuous beating. Personal Protective Equipment •...
-
Page 11: After Use
agents are still in the sprayer tank. • Review the troubleshooting table to proceed. 8. AFTER USE Drain Tank • Disconnect the power supply and relieve the system pressure by squeezing the spray gun trigger. • Use a suitable container to drain excess agent into, place it beneath the drain hole. -
Page 12: Troubleshooting
• Fill the sprayer tank with fresh clean water, connect the power, use the spray gun and flush the system. Be sure to have a container to collect the flushed antifreeze. • Dispose of antifreeze along with local authority guidelines. 10. -
Page 13: Disposal Guidelines
• Whether the pressure switch controls properly or not? Please see the details of switch adjustment. NOISE OR DYSFUNCTION • Whether the pipe is loose or not? • Whether the pipe is bending that cause's transmission noise? • Whether the pump feet are installed too loose or too tight? •... -
Page 15: Exploded View
13. EXPLODED VIEW... - Page 16 Made in China...