Canon EOS C300 Instruction Manual
  1. Manuals
  2. Brands
  3. Canon Manuals
  4. Camcorder
  5. EOS C300
  6. Instruction manual

Canon EOS C300 Instruction Manual

Hd camcorder
Hide thumbs Also See for EOS C300:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
PUB. DIE-0406-001
HD Camcorder
The warranty information for Australia and New Zealand is at the end of this Instruction Manual.

Advertisement

Table of Contents
loading

Related Manuals for Canon EOS C300

Summary of Contents for Canon EOS C300

  • Page 1 PUB. DIE-0406-001 HD Camcorder The warranty information for Australia and New Zealand is at the end of this Instruction Manual.

  • Page 2: Important Usage Instructions

    If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A., Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A. Tel No. (516)328-5600...
  • Page 3 For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/ environment. (EEA: Norway, Iceland and Liechtenstein)

  • Page 4: Important Safety Instructions

    Important Safety Instructions In these safety instructions the word “apparatus” refers to the Canon HD Camcorder EOS C300 / EOS C300 PL and all its accessories. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions.
  • Page 5 Highlights of the EOS C300/C300 PL The Canon HD Camcorder EOS C300/C300 PL has been designed to meet the demanding needs and highest expectations of industry professionals. The following are just some of the many features that will help turn your creative vision into reality.
  • Page 6 C300 / C300 PL camcorders to use the same settings, or embedded in the recording itself. Canon Log gamma for spectacular dynamic range Using the Canon Log gamma (A 109) you can get recordings with amazing dynamic range, allowing you to realize in post-production the artistic vision you desire.

  • Page 7: Table Of Contents

    Table of Contents 1. Introduction 11 About this Manual 11 Conventions Used in this Manual 11 Supplied Accessories 13 Names of Parts 14 Grip Unit 19 Monitor Unit 20 Handle Unit 22 2. Preparations 23 Preparing the Power Supply 23 Using a Battery Pack 23 Using a Household Power Outlet 25 Turning the Camcorder On and Off 26...
  • Page 8 Adjusting the Audio Level from the MIC Terminal 83 Monitoring the Audio with Headphones 84 Using Metadata 85 Setting a User Memo Created with Canon XF Utility 85 Setting a User Memo Using Wi-Fi Remote 86 Colors Bars/Audio Reference Signal 87...
  • Page 9 Embedded Audio 131 Selecting the Audio Channel 131 Saving Clips to a Computer 132 System Requirements 132 Installing and Uninstalling Canon XF Utility (Windows) 133 Installing and Uninstalling Canon XF Utility (Mac OS) 135 Viewing the Software Instruction Manuals 138 7.

  • Page 11: Introduction

    • Photographs in the manual are simulated pictures taken with a still camera. Some screenshots have been altered to make them easier to read. • Illustrations in the manual show the Canon EOS C300 camcorder with a Canon EF 50mm f/1.4 USM lens attached.
  • Page 12 About this Manual The arrow is used to abbreviate menu selections. For a detailed explanation on how to Using the Menus use the menus, refer to (A 29). For a concise summary of all available menu options and settings, refer to the appendix Menu Options (A 147).

  • Page 13: Supplied Accessories

    Comes pre-attached to the camcorder. Used to secure the optional WFT-E6 Wireless File Transmitter, when it is attached to the camcorder. The Canon XF Utilities Disc includes software for saving and managing clips on a computer. For details on installing the software, refer to Saving Clips to a Computer (A 132).

  • Page 14: Names Of Parts

    Names of Parts Names of Parts 1 MAGN. (magnification) button (A 70)/ Assignable button 1 (A 99) 2 PEAKING button (A 70) / Assignable button 2 (A 99) 3 ND FILTER +/- buttons (A 63) 4 ZEBRA button (A 72)/ Assignable button 3 (A 99) 5 WFM (waveform monitor) button (A 88)/ Assignable button 4 (A 99)
  • Page 15 17 WFT terminal (A 47) 18 EXT (external signal) terminals 1 and 2 (A 34) 19 REMOTE terminal For connecting commercially available remote controllers. 20 SYNC OUT (synchronizing signal output) terminal (A 79,129) 21 HDMI OUT terminal (A 129) 22 GENLOCK terminal (A 77) 23 TIME CODE terminal (A 78, 79) 24 HD/SD SDI terminal (A 129) 25 SD card access indicator (A 42)
  • Page 16 Names of Parts 32 START/STOP button (A 49) 33 # EF Lens mount index (A 32) 34 # EF-S Lens mount index (A 32) 35 # Lens release button (A 32) 36 # EF Lens lock pin (A 32) 37 # EF Lens mount (A 32) 38 # EF Lens contacts (A 32) 39 $ PL Lens mount (A 34) 40 $ Bayonet ring handles (A 34)
  • Page 17 43 Viewfinder unit 44 Viewfinder unit LOCK/RELEASE screw (A 171) (rear panel’s backlight) button (A 53) 46 FUNC. (main functions) button (A 57) 47 START/STOP button (A 49) 48 Joystick (A 29)/SET button (A 29) 49 CANCEL button (A 29) 50 MENU button (A 29) 51 CF card slots A (top) and B (bottom) (A 41) 52 RELEASE (battery release) latch (A 24)
  • Page 18 Names of Parts 65 Tape measure hooks Use the hooks to accurately measure the distance from the focal plane. Focal plane marks 67 Socket for the WFT Attachment Bracket (A 47) 68 Strap mounts (A 39) 70 TB-1 Tripod Base for tripods with 0.95 cm (3/8 in.) screws (A 37) 71 Tripod socket (A 37) 69 Accessory shoe with mounting hole for...

  • Page 19: Grip Unit

    Grip Unit 1 MAGN. (magnification) button (A 70)/ Assignable button 7 (A 99) 2 Control dial (A 62, 64) 3 START/STOP button (A 49) 4 Grip belt (A 39) 5 Joystick (A 29)/SET button (A 29) 6 Connection plug (A 38) 7 Lock screw (A 38) Names of Parts...

  • Page 20: Monitor Unit

    Names of Parts Monitor Unit Operation panel (A 21) 1 LCD panel 2 MIRROR button (A 36) 3 Microphone lock screw (A 80) 4 Microphone holder (A 80) 5 Microphone cable clamp (A 80) 6 XLR terminals CH1 (right) and CH2 (left) (A 80)
  • Page 21 Operation panel 7 DISP. (display) button (A 52, 115) 8 Ñ (stop) button (A 114)/ Assignable button 14 (A 99) 9 WFM (waveform monitor) button (A 88)/ Assignable button 8 (A 99) 10 Ú (skip backward) button (A 116)/ Assignable button 13 (A 99) 11 EDGE MON.

  • Page 22: Handle Unit

    Names of Parts Handle Unit 1 Mounting hole for 0.64 cm (1/4 in.) screws 2 Front accessory shoe 3 Top accessory shoe 4 Lock screw (A 39)

  • Page 23: Preparations

    Preparing the Power Supply You can power the camcorder using a battery pack or directly using the compact power adapter. If you connect the compact power adapter to the camcorder while a battery pack is attached, the camcorder will draw power from the power outlet.
  • Page 24 Preparing the Power Supply Attaching the Battery Pack 1 Set the Q switch to OFF. 2 Slide the BATT. OPEN switch in the direction of the arrow and open the battery compartment cover. 3 Insert the battery pack all the way into the compartment as shown in the illustration and press it gently toward the left until it clicks.

  • Page 25: Using A Household Power Outlet

    Press the BATT. INFO button to display the remaining battery time and available recording time (displays for 5 seconds). Depending on the battery life, the battery information may not be displayed. NOTES • The first time you use a battery pack, fully charge it and then use the camcorder until the battery pack is completely exhausted.

  • Page 26: Turning The Camcorder On And Off

    Preparing the Power Supply Turning the Camcorder On and Off The camcorder has two operating modes: CAMERA ( ) mode for making recordings and MEDIA ( mode for playing back recordings. Select the operating mode using the Q switch. To turn on the camcorder Set the Q switch to CAMERA for mode or MEDIA for mode.

  • Page 27: Date, Time And Language Settings

    Date, Time and Language Settings Setting the Date and Time You will need to set the date and time of the camcorder before you can start using it. When the camcorder’s clock is not set, the [Date/Time] screen will appear automatically with the first field selected (month or day, depending on the country/region of purchase).

  • Page 28: Displaying The Date And Time While Recording

    Date, Time and Language Settings Displaying the Date and Time while Recording You can display the date and time on the screen. Operating modes: 1 Press the MENU button. 2 Push the joystick up/down or turn the SELECT dial to select [£...

  • Page 29: Using The Menus

    Using the Menus mode, many of the camcorder’s functions can be adjusted from the menu for general settings, which opens after pressing the MENU button. You can also register frequently used menu settings in a customized submenu (My Menu) for easy access. In settings or SET to open the clip menu for clip operations.

  • Page 30: Using The Customized Submenu (My Menu)

    Using the Menus • The orange selection frame will appear on a setting option. • Press the CANCEL button to return to the previous submenu. 6 Push the joystick up/down or turn the SELECT dial to select the desired setting option and then press SET.
  • Page 31 Using the Menus Resetting the My Menu Submenu My Menu] 1 Reset all the menu settings registered to the My Menu submenu. My Menu] > [Edit] > [Reset All] [Edit] 2 Select [OK] and then press SET twice. [Reset All]...

  • Page 32: Preparing The Camcorder

    Preparing the Camcorder Preparing the Camcorder This section outlines the basic preparations for the camcorder such as attaching a lens and attaching the modular units to the camcorder: monitor unit, grip unit, handle unit, thumb rest, eye cup, etc. Your camcorder is nothing if not versatile and you can choose the configuration that best fits your needs and shooting conditions.
  • Page 33 • If correction data is not available, [Periph. Illum. Corr.] will appear grayed out. Visit your local Canon Web site and check if there is correction data available for the lens you are using. If so, download the necessary update package and upgrade the camcorder’s firmware following the instructions supplied therein.

  • Page 34: Attaching And Removing The Monitor Unit

    Correction data for future lenses will be made available as part of the regular updates released for the camcorder’s firmware. For more details, visit your local Canon Web site. - Depending on the recording conditions, noise may appear in the periphery of the image as a result of the correction.

  • Page 35: Using The Viewfinder

    Removing the Monitor Unit 1 Set the Q switch to OFF. 2 Disconnect the monitor unit’s cables from the camcorder’s EXT 1 and EXT 2 terminals. • Pull back the metallic tips of the cable to release the cable and then disconnect the cable. 3 Unscrew the lock screw and then gently slide out the monitor unit from the accessory shoe.

  • Page 36: Using The Lcd Panel

    Preparing the Camcorder Dioptric Adjustment Turn on the camcorder and adjust the dioptric adjustment dial. Attaching the Viewfinder Cap Pointing the viewfinder lens at the sun or other strong light sources may cause damage to internal components. When you are not using the viewfinder, make sure to attach the viewfinder cap to the viewfinder.

  • Page 37: Adjusting The Viewfinder/Lcd Screen

    • While recording with the LCD panel rotated in a different direction or angle (for example, facing toward the subject), you can press the MIRROR button repeatedly to invert the image on the screen horizontally, vertically or both ways. Adjusting the Viewfinder/LCD Screen You can adjust the brightness, contrast, color, sharpness, and backlight of the viewfinder and LCD screen independently of each other.

  • Page 38: Removing And Attaching The Grip Unit

    Preparing the Camcorder Using a Tripod with 0.64 cm (1/4 in.) Mounting Screws To use a tripod with 0.64 cm (1/4 in.) mounting screws, first attach the supplied tripod adapter base to the camcorder and then attach the tripod to the adapter base. 1 Remove the original TB-1 tripod base from the camcorder.

  • Page 39: Attaching The Handle Unit

    Adjusting the Grip Belt Adjust the grip belt so that you can reach the START/STOP button on the grip unit with your index finger but still have a comfortable but secure grip. IMPORTANT • Be careful not to drop the camcorder when adjusting the grip belt. Attaching the Handle Unit 1 Insert the attachment base at the bottom of the handle unit to the camcorder’s accessory shoe.
  • Page 40 Preparing the Camcorder Attaching the Terminal Covers Insert the connecting strip into the opening to attach the terminal cover. NOTES • If the connecting strip is difficult to grasp, use a pair of tweezers or similar tool.

  • Page 41: Preparing Recording Media

    * The camcorder can record custom picture files and a camera settings file onto the SD card as well. The SD card serves also to store user memo files created with the supplied software Canon XF Utility that you can then read and embed in the clips’...

  • Page 42: Removing A Cf Card

    Preparing Recording Media Removing a CF card 1 Wait until the access indicator for the card slot with the CF card to be removed is off. 2 Slide the CF card slot cover switch in the direction of the arrow. •...

  • Page 43: Initializing The Recording Media

    Initializing the Recording Media The first time you use any recording media with this camcorder, initialize it first. You can also initialize a recording media to permanently delete all the data it contains. When initializing an SD card, you can select quick initialization, which clears the file allocation table but does not physically erase the stored data, or complete initialization, which deletes all data completely.

  • Page 44: Selecting The Cf Card Recording Method

    Preparing Recording Media Press the SLOT SELECT button. • The access indicator of the selected CF card slot will illuminate in green. On the screen, the CF card selected is indicated with a Ð mark next to CF card icon and in the rear panel, with a Î mark on top of the CF card icon.

  • Page 45: Checking The Available Recording Time

    Checking the Available Recording Time When the camcorder is in mode, the display on the upper left of the screen indicates which CF card slot is in use and the available recording time (in minutes*) that remains on each CF card. The same information is displayed in the rear panel.

  • Page 46: Adjusting The Black Balance

    Adjusting the Black Balance Adjusting the Black Balance You can have the camcorder adjust the black balance automatically when ambient temperature changes considerably or if there is a noticeable change in a true black video signal. Operating modes: 1 Open the [ABB] screen. [~ Camera Setup] >...

  • Page 47: Remote Operation Via The Wi-Fi Remote Application

    * For details about compatible devices, operating systems, Web browsers, etc. please visit your local Canon Web site. Operating modes:...
  • Page 48 Remote Operation Via the Wi-Fi Remote Application...

  • Page 49: Recording

    Recording Video This section explains the recording basics. Before you begin recording, make a test recording first to check if the camcorder operates correctly. Record for approximately 6 minutes at 50 Mbps (A 55). Should the camcorder Troubleshooting fail to operate correctly, refer to For details on recording audio, refer to Operating modes: Preparing to Record...

  • Page 50: Remote Operation Using Wi-Fi Remote

    - Do not open the CF card slot cover of the CF card slot being accessed and remove the CF card. - Do not disconnect the power source or turn off the camcorder. • Be sure to save your recordings regularly (A 132), especially after making important recordings. Canon shall not be liable for any loss or corruption of data.
  • Page 51 • You can use [w Other Functions] > [Clips] > [Delete Last Clip] (A 153) to delete the last clip recorded. However, you cannot delete the last clip if double slot recording is on. • When you set the [w Other Functions] > [SDI Rec Command] setting to [On] and you connect the camcorder to another device using the HD/SD SDI terminal, if you start or stop recording with the camcorder, the other device will also start or stop recording.

  • Page 52: Onscreen Displays

    Recording Video Onscreen Displays Refer to this section for an explanation of the various screen displays that appear in the custom display function ( When displaying the date and time ( 1 Remaining battery time (A 53) 2 CF card status/available recording time (A 53) 3 Remaining recording time for double slot recording (A 44) 4 # Current focal length of an attached EF lens*...

  • Page 53: Rear Panel Displays

    1 Remaining battery time • The icon shows a rough estimate of the remaining charge as a percentage of the full charge of the battery pack. The remaining recording/playback time of the battery pack is displayed, in minutes, next to the icon. •...

  • Page 54: Cinema Preset

    • [/ LOCKED] appears on the left of the screen. NOTES • When Canon Log gamma is used, the image displayed on the screen will appear darker than usual. You can use the view assistance function (A 109) to display an image that approximates the one that would be obtained using a normal gamma setting.

  • Page 55: Video Configuration: Type Of Recording, Bit Rate, Resolution And Frame Rate

    Video Configuration: Type of Recording, Bit Rate, Resolution and Frame Rate Before you record, select the bit rate, resolution (frame size) and frame rate that best match your creative needs. The options available will depend on the type of recordings you select: NTSC-compatible, PAL-compatible or true 24.00P recordings.
  • Page 56 Video Configuration: Type of Recording, Bit Rate, Resolution and Frame Rate Available bit rate, resolution and frame rate settings [24.00P] set to [On] Bit rate* Resolution Frame rate 24.00P Ü 1920 x 1080 50 Mbps (CBR 4:2:2) Ü 1280 x 720 1920 x 1080 –...

  • Page 57: Changing Main Camera Functions With The Func. Button

    Changing Main Camera Functions with the FUNC. Button You can adjust three main camera functions –shutter speed, white balance and ISO speed/gain– using the FUNC. button (direct setting mode). In direct setting mode, you can change settings using the LCD screen/ viewfinder or using only the rear panel, which is convenient when the monitor unit is not attached to the camcorder.

  • Page 58: Shutter Speed

    Shutter Speed Shutter Speed Set the shutter speed based on the recording conditions. For example, you may want to set slower shutter speeds in darker environments. The camcorder offers the following 5 modes. Operating modes: [Speed]: Allows you to set the shutter speed (in fractions of a second). You can select the increment to use when adjusting the shutter speed between 1/3-stop and 1/4-stop increments.

  • Page 59: Changing The Shutter Speed Mode And Value

    Changing the Shutter Speed Mode and Value 1 Open the shutter [Mode] submenu. [~ Camera Setup] > [Shutter] > [Mode] 2 Select the desired mode and then press SET. • If you selected [Speed] (the default value) you can select the increment scale to use when adjusting the shutter speed;...
  • Page 60 Shutter Speed Using Slow Shutter Mode When recording in dark surroundings, you can obtain a brighter picture by using slow shutter mode. You can also use this mode when you wish to add certain effects to your recordings, such as blurring the background during panning shots or recording a moving subject with an afterimage trail.

  • Page 61: Iso Speed/Gain

    * The minimum and maximum ISO speeds are available even when the 1-stop increment scale is selected. **ISO speed required for a suitable dynamic range for Canon Log gamma. Equivalent to a gain value of 2.5 dB. Changing the ISO Speed or Gain Value 1 Open the ISO Speed/Gain [Select] submenu.

  • Page 62: Using The Control Dial

    ISO Speed/Gain Using the Control Dial You can adjust the value of the ISO speed or gain using the control dial on the camcorder or that on the grip unit. You will need to set the control dial’s function to [ISO/Gain] in advance. Assigning ISO Speed/Gain Control to the Control Dial 1 Open the [Control Dial] submenu.

  • Page 63: Nd Filter

    ND Filter Using the ND filters allows you keep the aperture within an appropriate range when recording in bright surroundings*. * Closing down the aperture when recording under bright conditions may cause the picture to appear soft or out of focus. To avoid the loss of sharpness due to diffraction, use a denser ND filter or a faster shutter speed (A 58).

  • Page 64: Adjusting The Aperture

    # Adjusting the Aperture # Adjusting the Aperture You can affect the brightness of your recordings or change the depth of field by adjusting the aperture. For example, use a small aperture value for a shallow depth of field that isolates the subject in focus and nicely blurs the background.
  • Page 65 1 Press the current aperture value on the Wi-Fi Remote screen. 2 Select the desired aperture value from the list. • You may need to scroll up/down to see all the available values. • Alternatively, you can press IRIS [+] to open the aperture or IRIS [-] to close the aperture in 1/8-stop increments.

  • Page 66: White Balance

    White Balance White Balance The camcorder uses an electronic white balance process to calibrate the picture and ensure accurate colors under different lighting conditions. There are 3 methods of setting the white balance. Custom white balance: You can use a white object to establish the white balance and set it to one of two custom white balance positions, ÅA or ÅB.

  • Page 67: Remote Operation Using Wi-Fi Remote

    3 Push the joystick up/down or turn the SELECT dial to change the adjustment value and then press SET. • The selected adjustment value will be set and the camcorder will exit the direct setting mode. • On the screen: The selected adjustment value will appear next to the white balance icon. On the rear panel: The adjustment value display will disappear and the display will return to normal (all displays will reappear).
  • Page 68 White Balance • The selected value will be displayed on the Wi-Fi Remote screen and will be applied on the camcorder. If you selected ÅA or ÅB: 3 Point the camcorder at a white object so that it fills the whole screen. •...

  • Page 69: Adjusting The Focus

    Adjusting the Focus The camcorder does not have automatic focus control and focusing is done manually using the focus ring on the attached lens. Nevertheless, the camcorder offers focus assistance functions to help you adjust the focus more accurately. # only: You can adjust the focus of an attached EF lens remotely using the Wi-Fi Remote application. Operating modes: Adjusting the Focus Manually Turn the focus ring on the attached lens to adjust the focus.

  • Page 70: Using The Focus Assistance Functions

    Adjusting the Focus NOTES • If the focus mode switch on the EF lens is set to MF, you will not be able control the focus through remote operation. Depending on the lens used, remote operation may not work correctly. •...

  • Page 71: Onscreen Markers And Zebra Patterns

    Onscreen Markers and Zebra Patterns Using onscreen markers allows you to make sure your subject is correctly framed and is within the appropriate safe area. The zebra patterns help you identify areas that are overexposed. The onscreen markers and zebra pattern will not affect your recordings.

  • Page 72: Displaying Zebra Patterns

    Onscreen Markers and Zebra Patterns NOTES • If you set an assignable button to [Markers] (A 99), you can press the button to turn the onscreen markers on and off. Displaying Zebra Patterns The camcorder has a zebra pattern feature that shows black and white diagonal stripes over areas that are overexposed.

  • Page 73: Setting The Time Code

    Setting the Time Code The camcorder can generate a time code signal and embed it in your recordings. You can have the camcorder output the time code signal from the HD/SD SDI terminal or TIME CODE terminal (A 79). In addition, you can superimpose the time code on video output from the HDMI OUT terminal or SYNC OUT terminal.

  • Page 74: Selecting Drop Or Non-Drop Frame

    Setting the Time Code • The time code setting screen appears with an orange selection frame indicating the hours. • To reset the time code to [00:00:00.00], select [Reset] instead. If the running mode is set to [Free Run], the time code will be reset the moment you press SET and keep running continuously from 00:00:00.00.
  • Page 75 NOTES • When [w Other Functions] > [24.00P] is set to [On] or [w Other Functions] > [Frame Rate] is set to [23.98P], the frames value in the time code runs from 0 to 23. When [Frame Rate] is set to [25.00P], [50.00i] or [50.00P], it runs from 0 to 24.

  • Page 76: Setting The User Bit

    Setting the User Bit Setting the User Bit The user bit display can be selected from the date or the time of recording, or an identification code consisting of 8 characters in the hexadecimal system. There are sixteen possible characters: the numbers 0 to 9 and the letters A to F.

  • Page 77: Synchronizing With An External Device

    Synchronizing with an External Device Using genlock synchronization, you can synchronize this camcorder’s video signal to that of an external video device. Similarly, using an external time code signal, you can synchronize this camcorder’s time code to the external signal. Using the external time code signal with multiple cameras allows you to set up a multi-camera recording.

  • Page 78: Time Code Signal Input

    Synchronizing with an External Device Time Code Signal Input An external SMPTE-standard LTC timing signal received from the TIME CODE terminal will be recorded as the time code. The user bit of the external timing signal can also be recorded. Before connecting the device, set the TIME CODE terminal to input.

  • Page 79: Reference Video Signal Output

    Reference Video Signal Output You can output the camcorder’s video signal as a reference sync signal (analog blackburst or tri-level signal) through the SYNC OUT terminal to synchronize an external device to this camcorder. Operating modes: 1 Open the [SYNC Output] submenu. [¢...

  • Page 80: Recording Audio

    Recording Audio Recording Audio The camcorder features two-channel linear PCM audio recording and playback with a sampling frequency of 48 kHz. You can record audio using commercially available microphones (XLR terminal, MIC terminal) or line input (XLR terminal). You can select the audio input independently for channel 1 and channel 2. Operating modes: Connecting an External Microphone or External Audio Input Source to the Camcorder In order to use the XLR terminals, the monitor unit must be attached to the camcorder.

  • Page 81: Selecting The Audio Input From The Xlr Terminals

    Selecting the Audio Input from the XLR Terminals Using the XLR terminals CH1 and CH2, you can record audio independently to the two audio channels from a microphone or analog audio input source. Note that the camcorder’s MIC terminal is given priority over the XLR terminals.

  • Page 82: Adjusting The Audio Level From The Xlr Terminals

    Recording Audio Adjusting the Audio Level from the XLR Terminals You can set the audio recording level for audio input from the XLR Terminals to auto or manual for each channel. Automatic Audio Level Adjustment Set the ã switch of the desired channel to A (automatic) to let the camcorder automatically adjust that channel’s audio level.

  • Page 83: Adjusting The Audio Level From The Mic Terminal

    Available Sensitivity Levels +12 dB +6 dB 0 dB -6 dB Activating the Microphone’s Attenuator You can activate the microphone’s attenuator (20 dB) if the XLR terminal switch is set to MIC or MIC+48V. 1 Open the desired XLR terminal’s microphone attenuator submenu. [¡...

  • Page 84: Monitoring The Audio With Headphones

    Recording Audio Activating the Microphone’s Attenuator If the audio level is too high and the sound sounds distorted, activate the microphone attenuator (20 dB). 1 Open the [MIC Att.] submenu. [¡ Audio Setup] > [Audio Input] > [MIC Att.] 2 Select [On] and then press SET. Monitoring the Audio with Headphones Connect headphones* to the ×...

  • Page 85: Using Metadata

    Setting a User Memo Created with Canon XF Utility Before you can add a user memo, you must first install the supplied Canon XF Utility software (A 132). Next, create the user memo and then save it to an SD card. Once you insert the SD card in the camcorder and select the user memo, it will be added to clips you record.

  • Page 86: Setting A User Memo Using Wi-Fi Remote

    Wi-Fi-enabled device using the Wi-Fi Remote application. Using the Wi-Fi Remote application you have two additional advantages over user memos created with Canon XF Utility: you can change the user memo of the last clip recorded, even if you did not specify a user memo in advance; and you can enter manually the GPS information of your shooting location.

  • Page 87: Colors Bars/Audio Reference Signal

    Colors Bars/Audio Reference Signal You can have the camcorder generate and record color bars and a 1 kHz audio reference signal and output them from the HD/SD SDI terminal, HDMI OUT terminal, SYNC OUT terminal Outputs color bars only. Outputs audio reference signal only. Operating modes: Recording Color Bars You can choose between SMPTE standard-definition color bars, EBU...

  • Page 88: Video Scopes

    Video Scopes Video Scopes The camcorder can display a simplified waveform monitor or vectorscope. It can also display an edge monitor* to help you focus. The video scopes appear only on the LCD screen. They do not appear in the viewfinder or on an external monitor.

  • Page 89: Configuring The Vectorscope

    Configuring the Vectorscope The camcorder’s vectorscope function offers 2 modes. You can also change the gain. 1 Open the [Vectorscope] submenu. [w Other Functions] > [WFM (LCD)] > [Vectorscope] 2 Select the desired option and then press SET. • If you do not need to change the gain, you do not need to perform steps 3 and 4.

  • Page 90: Adding Marks While Recording

    Adding Marks while Recording Adding Marks while Recording When recording, you can flag an important shot in a clip by adding a “shot mark” (!). There are two types of shot marks, shot mark 1 (") and shot mark 2 (#), and you can add either or both types to a single clip. You can also add an OK mark ($) or check mark (%) to the entire clip to flag clips you want to set apart.

  • Page 91: Adding An $ Mark Or % Mark To The Last Clip Recorded

    NOTES • There may be up to a 0.5 second delay from when you press the button to when the camcorder adds the shot mark. When using the Wi-Fi Remote application, the delay may be longer depending on the conditions of the wireless signal.

  • Page 92: Reviewing A Recording

    Reviewing a Recording Reviewing a Recording When the camcorder is in was recorded. Operating modes: 1 Open the [Rec Review] submenu to set the review length. [w Other Functions] > [Rec Review] 2 Select the desired option and then press SET. 3 After you finish recording, press the •...

  • Page 93: Special Recording Modes

    Special Recording Modes The camcorder features 4 special recording modes. Interval recording ([Interval Rec]): The camcorder will automatically record a pre-defined number of frames at a pre- defined interval. This mode is suitable for recording subjects with little movement, such as natural surroundings or plants. Frame recording ([Frame Rec]): The camcorder will record a pre-defined number of frames every time you press the START/STOP button.

  • Page 94: Frame Recording Mode

    Special Recording Modes 4 Press the START/STOP button again to stop recording. • All of the recorded frames are joined together into one clip. • The tally lamps go out and [INT STBY] appears at the top of the screen (with [INT] flashing). NOTES •...

  • Page 95: Slow & Fast Motion Mode

    5 Select [Off] and then press SET. • Frame recording mode ends and all of the recorded frames are joined together into one clip. • The tally lamp goes out and [STBY] appears at the top of the screen. NOTES •...

  • Page 96: Pre-Recording Mode

    Special Recording Modes Activating Slow & Fast Motion Mode and Recording 1 Open the [Special Rec] submenu. [w Other Functions] > [Special Rec] 2 Select [Slow & Fast Motion] and then press SET. • [S&F STBY] appears at the top of the screen. •...
  • Page 97 1 Open the [Special Rec] submenu. [w Other Functions] > [Special Rec] 2 Select [Pre Rec] and then press SET. • [PRE REC STBY] appears at the top of the screen. 3 Press the START/STOP button to begin recording. • The tally lamp illuminates. •...
  • Page 98 Special Recording Modes...

  • Page 99: Customization

    Assignable Buttons The camcorder conveniently features 15* buttons to which you can assign various functions. By assigning often- used functions, you can quickly access them with a single press of a button. Some assignable buttons are located on the monitor unit or grip unit, so their availability depends on the camcorder configuration used. * In mode, only assignable buttons 1 to 9 are available.

  • Page 100: Using An Assignable Button

    Assignable Buttons Using an Assignable Button After you assign a function to one of the buttons, press the button to activate the function. For some functions, an options menu may appear. In such case, select the desired option and then press SET. Assignable Functions Functions can be set separately in functions and available modes.

  • Page 101: Custom Picture Settings

    By default, the custom picture files in the camcorder in file slots [C8] and [C9] are protected. Remove the protection (A 102) to edit the file. The following describes when to use the preset files. [C8: CINEMA]: Uses the Canon Log gamma and color matrix for an outstanding dynamic range and an image suitable for processing in post-production.

  • Page 102: Renaming Custom Picture Files

    Custom Picture Settings 3 Change the setting to the desired level and then press SET. Available Custom Picture Settings • Refer to the table • Repeat steps 2 and 3 for other settings, as necessary. 4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the new custom picture settings.
  • Page 103 Copying a File from the Camcorder to an SD Card 1 After selecting a file in the camcorder, open the [Copy To *] submenu. [+ / Transfer File] > [Copy To *] 2 Select the file slot on the SD card under which to save the file and then press SET.

  • Page 104: Embedding Custom Picture Settings In A Recording

    Use [Cine 1] for a gamma curve that results in a picture with a cinema-like feel and cinema-like tones. [Cine 2] has softer contrasts than does [Cine 1] but is also suitable for creating a cinema-like picture. [Canon Log]: Applies a logarithmic gamma curve for outstanding dynamic range. Requires image processing in post-production.
  • Page 105 Controls the lower part of the gamma curve (dark areas of the image). This setting is not available when [Gamma] is set to [Canon Log]. [Level]: Raises or lowers the lower part of the gamma curve. This setting can be adjusted from -50 to 50.
  • Page 106 Controls the upper part of the gamma curve (highlights of the image). By compressing the highlights, you can prevent parts of the image from being overexposed. This is not available when [Gamma] is set to [Cine 1], [Cine 2], [Canon Log] or [EOS Std.]. [Enable]: Activates/deactivates the setting.
  • Page 107 [Knee Aperture]: Allows you to set the sharpness of only the areas above the knee point by adjusting the gain and slope. This is not available when [Gamma] is set to [Cine 1], [Cine 2], [Canon Log] or [EOS Std.].
  • Page 108 Custom Picture Settings [Select]: Available options are [Normal 1] to [Normal 4], [Cine 1] and [Cine 2], [Canon Log] and [EOS Std.]. Generally, this is the same setting as [Gamma]. After selecting an option, you can make more precise adjustments. (Default: [Normal 1]) [Gain]: Adjusts the color intensity.

  • Page 109: Canon Log Gamma

    Checking clips recorded with Canon Log gamma When Canon Log gamma is used, the image displayed on the screen will appear darker than usual. You can use the view assistance function to display an image that approximates the one that would be obtained using a normal gamma setting.

  • Page 110: Customizing Functions And Onscreen Displays

    Customizing Functions and Onscreen Displays Customizing Functions and Onscreen Displays Customize the camcorder to match your shooting style and needs. Use the [w Other Functions] > [Custom Function] setting to adjust how some of the camcorder’s controls and functions operate in Similarly, use the [£...

  • Page 111: Saving And Loading Camera Settings

    [w Other Functions] > [Wi-Fi] are not saved: the encryption key/WEP index key in the wireless LAN setup of each of the configuration files [No. 1] to [No. 5] and the password in the camcorder settings. • Camera settings from Canon XF100 / XF105 / XF300 and XF305 camcorders cannot be used with this camcorder.
  • Page 112 Saving and Loading Camera Settings...

  • Page 113: Playback

    Playback This section explains how to play back clips recorded on a CF card. For details on playing back clips using an Connecting to an External Monitor external monitor, refer to Viewing Photos card, refer to (A 141). Operating modes: Clip Index Screen Playback functions are accessed from the clip index screen.

  • Page 114: Playing Back Clips

    Playback 1 $ mark/% mark (A 91, 120) 2 Orange selection frame 3 Relay recording: Appears when a clip begins on one CF card and continues on the other. (A 44) 4 Shot mark (A 90, 124) 5 Recording date and time 6 Clip name (A 51) 7 Clip thumbnail (A 125) 8 Currently selected CF card slot (A 43)

  • Page 115: Onscreen Displays

    • Playback will start from the clip selected and continue until the end of the last clip in the index screen. When the last frame of the last clip is reached, playback will be paused. • Press the Ò button again or press SET to pause/resume the playback. •...

  • Page 116: Playback Controls

    Playback 7 Playback operation Ð PLAY Ý PAUSE Ô/Ó F FWD × Ø F REV * The playback speed (x5, x15 or x60) will also appear in the indicator. 9 Relay recording Appears when a clip begins on one CF card and continues uninterrupted on the other. 5 indicates the first part of the recording, 6 indicates the middle part(s) and 7 indicates the last part.

  • Page 117: Adjusting The Volume

    Adjusting the Volume During playback, audio will be available through the × (headphone) terminal; the audio signal will also be output through the HD/SD SDI terminal and the HDMI OUT terminal. Adjusting the Headphone Volume Press the HEADPHONE +/- buttons to adjust the volume. NOTES •...

  • Page 118: Clip Operations

    Clip Operations Clip Operations Besides playing back a clip, you can perform other operations such as deleting a clip or displaying clip information. This is done through the clip menu, which contains different functions depending on the index screen. You can use the functions in the [w Other Functions] menu to perform some of the operations on all the clips.

  • Page 119: Displaying Clip Information

    2 Select the desired function and then press SET. • The function is enabled. For some functions, further action may be required. Follow the onscreen directions. • Press the CANCEL button instead to return to the clip index screen. IMPORTANT •...

  • Page 120: Adding $ Marks Or % Marks

    Clip Operations Displaying Custom Picture Settings When displaying the [Clip Info] screen of a clip that has a custom picture file recorded with it, push the joystick down or turn the SELECT dial down to display the first of three screens with the clip’s custom picture settings ([/ Data 1/3] screen).

  • Page 121: Copying Clips

    Deleting $ Marks from All Clips 1 Open the [Delete All $ Marks] submenu. [w Other Functions] > [Delete All $ Marks] 2 Select [OK] and then press SET. • All $ marks from clips on the selected CF card will be deleted. •...

  • Page 122: Deleting Clips

    Clip Operations NOTES • You cannot copy a clip if either CF card slot cover is open. • If a clip is being copied to a card that already has a clip with the same number (the last 4 digits in the clip name), then the copied clip will be renamed with the following number.

  • Page 123: Displaying An Index Screen Of Shot Marks

    • The [/ Data 1/3] screen appears with the orange selection frame indicating a custom picture file slot in the camcorder. • Alternatively, you can press the CUSTOM PICTURE button. • You can push the joystick up/down or turn the SELECT dial to display the [/ Data 2/3] and [/ Data 3/3] screens.

  • Page 124: Displaying A Frame Index Screen Of A Single Clip

    Clip Operations Displaying a Frame Index Screen of a Single Clip You can display an index screen of a single clip broken down as frames at fixed intervals. This is useful when you have a long clip or wish to play back a clip from a certain point. You can change how many thumbnails are displayed.

  • Page 125: Deleting Shot Marks

    3 Select [Add Shot Mark 1] or [Add Shot Mark 2] and then press SET. • The clip information screen appears and it prompts you to confirm the operation. 4 Select [OK] and then press SET. • The screen changes back to the previous index screen and the selected shot mark appears next to the selected clip’s thumbnail.
  • Page 126 Clip Operations...

  • Page 127: External Connections

    Video Output Configuration The video signal output from the HD/SD SDI, HDMI OUT and SYNC OUT terminals depends on the clip’s video configuration, the capability of the external monitor (for video output from the HDMI OUT terminal) and on various menu settings.

  • Page 128: Connecting To An External Monitor

    Connecting to an External Monitor Connecting to an External Monitor When you connect the camcorder to an external monitor for recording or playback, use the terminal on camcorder that matches the one you wish to use on the monitor. Then, select the video signal output configuration (A 127).

  • Page 129: Using The Hd/Sd Sdi Terminal

    Using the HD/SD SDI Terminal The digital signal output from the HD/SD SDI terminal includes the video signal, audio signal and time code signal. If necessary, perform the following procedure to change the output to HD or SD*. Turning the output off will conserve the camcorder’s power.

  • Page 130: Sd Output

    Connecting to an External Monitor SD Output When HD video (16:9 aspect ratio) is converted and output as SD video (4:3 aspect ratio), you can choose how it appears on the external monitor. 1 Open the [SD Output] submenu. [¢ Video Setup] > [SD Output] 2 Select the desired option and then press SET.

  • Page 131: Audio Output

    Audio Output The camcorder can output audio from the HD/SD SDI terminal HDMI OUT terminal or × (headphone) terminal. When audio is output from the × (headphone) terminal, you can configure settings such as the output channel. Embedded Audio Embedded audio refers to the superimposing of the audio signal along with the video signal being output from the HD/SD SDI terminal.

  • Page 132: Saving Clips To A Computer

    Saving Clips to a Computer Saving Clips to a Computer Use the software on the supplied Canon XF Utilities CD-ROM to transfer clips in the camcorder to a computer to save them. The CD-ROM contains the following. Canon XF Utility: Browser for transferring clips to a computer, playing back and checking video, and managing clips.
  • Page 133 English, French, Spanish, Italian or German (available languages depend on the region you select). However, only the English version of the software is included in the supplied Canon XF Utilities CD-ROM. After installing this version, you can download language packs that will change the user interface (menus, messages, etc.) to other languages.
  • Page 134 8 Click [Next] and then click [Finish]. 9 Remove the CD-ROM from the computer. Uninstalling Canon XF Utility 1 From the Start menu, select All Programs > Canon Utilities > Canon XF Utility > Uninstall Canon XF Utility. • A confirmation screen appears.
  • Page 135 Uninstalling the Canon XF Plugin for Avid Media Access Instructions 1 From the Start menu, open All Programs > Canon Utilities > Canon XF Plugin for Avid Media Access > Uninstall Canon XF Plugin for Avid Media Access Instruction Manual.
  • Page 136 Saving Clips to a Computer 4 Click [Install]. 5 Select the installation method and then click [Next]. 6 Read the license agreement and click [Agree]. • If you do not select [Agree], you cannot install the software. • If you selected the [Easy Installation] installation method, skip to step 8. 7 Select the software to install and then click [Next].
  • Page 137 Uninstalling the Canon XF Plugin for Final Cut Pro Instructions 1 From Applications, open Canon Utilities. 2 Drag and drop Canon XF Plugin for Final Cut Pro to Trash. Uninstalling the Canon XF Plugin for Avid Media Access Instructions 1 From Applications, open Canon Utilities.

  • Page 138: Viewing The Software Instruction Manuals

    Viewing the Plugin Instructions Canon XF Plugin for Avid Media Access Instructions (Windows): 1 From the Start menu, select All Programs > Canon Utilities > Canon XF Plugin for Avid Media Access > Canon XF Plugin for Avid Media Access Instruction Manual.

  • Page 139: Photos

    Taking Photos You can take photos when the camcorder is in camcorder is in mode. Photos are saved onto the SD card. In mode, photo size depends on the resolution setting of the clip that the photo is captured from. If the clip is 1920x1080 or 1440x1080, the photo size is 1920x1080.
  • Page 140 Taking Photos IMPORTANT • Observe the following precautions while the SD card access indicator is flashing. Failure to do so may result in permanent data loss. - Do not disconnect the power source or turn off the camcorder. - Do not remove the SD card. NOTES •...

  • Page 141: Photo Playback

    Photo Playback You can view the photos that you took with the camcorder. Operating modes: Displaying the [Photos] Index Screen Display the [Photos] index screen to view photos. 1 Set the Q switch to MEDIA. • The camcorder switches to appears.

  • Page 142: Photo Operations

    Photo Operations Photo Operations You can use the photo menu to protect or unprotect a photo, delete a photo, or copy a custom picture file embedded in a photo. You can display the photo menu from the [Photos] index screen or photo playback screen.

  • Page 143: Protecting Photos

    Deleting All Photos 1 Open the [Delete All Photos] submenu. [w Other Functions] > [Delete All Photos] 2 Select [OK] and then press SET. • All of the photos on the SD card, except for protected ones, will be deleted. •...

  • Page 144: Copying Custom Picture Files

    Photo Operations IMPORTANT • Initializing an SD card will permanently erase all the data it contains, including protected photos and custom picture files. Copying Custom Picture Files You can copy to the camcorder a custom picture file embedded in a photo. Custom picture files can be copied from the photo playback screen or [Photos] index screen.

  • Page 145: Photo Numbering

    Photo Numbering Photos are automatically assigned consecutive numbers from 0101 to 9900, and stored on the SD card in folders containing up to 100 photos. Folders are numbered from 101 to 998. You can select the photo numbering method to be used. The photo number indicates the name and location of the file on the SD card.
  • Page 146 Photo Operations...

  • Page 147: Additional Information

    Menu Options For details about how to select an item, refer to the reference page. Menu items without a reference page are explained after the tables. Setting options in boldface indicate default values. Menu items not available appear grayed out. To skip directly to the page of a specific menu: [~ Camera Setup] menu [¡...
  • Page 148 Menu Options [¡ Audio Setup] menu Menu item [Audio Input] [XLR Rec Channel] [XLR1 Mic Trimming] [XLR2 Mic Trimming] [XLR1 Mic Att.] [XLR2 Mic Att.] [XLR ALC Link] [Limiter] [1 kHz Tone] [MIC Mode] [MIC Level] [MIC Att.] [Audio Output] [Channel] [Headphone Volume] * Not available in the [Photos] index screen.
  • Page 149 [£ LCD/VF Setup] menu Menu item Submenu [LCD Setup] [Brightness] [Contrast] [Color] [Sharpness] [Backlight] [VF Setup] [Brightness] [Contrast] [Color] [Sharpness] [Backlight] [LCD/VF B&W] [LCD/VF Simul.] [View Assist.] [Peaking] [Select] [Peaking 1] [Color] [Gain] [Frequency] [Peaking 2] [Color] [Gain] [Frequency] [Zebra] [Select] [Zebra 1 Level] [Zebra 2 Level]...
  • Page 150 Menu Options Menu item [Custom Display 1] [Custom Picture] # [Focal Length] [ND Filter] [Key Lock] [White Balance] # [Iris] [ISO/Gain] [Shutter] [Peaking] [Magnification] [View Assist.] [Custom Display 2] [Remaining Battery] [Remaining Rec Time] [Rec Mode] [Genlock] [Time Code] [Interval Counter] [SD Card Status] [Bit Rate/Resolution] [Frame Rate]...
  • Page 151 [Peaking]: Displays the peaking icon (J or K) when set to [On]. [Magnification]: Displays the screen magnification icon (^) when set to [On], indicating that the image on the screen is being magnified. [View Assist.]: Displays the view assistance icon ( [Custom Display 2] settings [Remaining Battery]: Controls when the remaining battery indicator appears.
  • Page 152 Menu Options Menu item [User Bit] [Rec Mode] [Output Mode] [Type] * In the following cases, the time code is set to [NDF] and this setting cannot be changed: - [w Other Functions] > [24.00P] is set to [On] - [w Other Functions] > [NTSC/PAL] is set to [PAL] - [w Other Functions] >...
  • Page 153 Menu item Submenu [Bit Rate/Resolution] [Frame Rate] [Special Rec] [Interval Rec] [Interval] [Rec Frames] [Frame Rec] [Rec Frames] [Slow & Fast Motion] [S&F Frame Rate] [Clips] [Title Prefix] [Number setting] [Delete Last Clip] [Copy All Clips] [Copy $ Clips] [Delete All Clips] [Delete All $ Marks] [Rec Review] [Set Metadata]...
  • Page 154 [Reverse], [Normal] [Reverse], [Normal] [Reverse], [Normal] [Both], [Magnify], [Peaking], [Off] [Both], [Vertical], [Horizontal], [Off] [On], [Off] [Cancel], [OK] For details refer to “WFT-E6 Wireless File Transmitter - Guide for Canon Camcorders” (PDF file). [Cancel], [OK] [Complete], [Quick] – Ü – –...
  • Page 155 [Number Setting]: Determines the last 4 digits of the clip name. Combined with the [Title Prefix] setting, this constitutes the 6-character clip name. Select [Set] to assign a desired number to the first clip you record or select [Reset] to reset the number to [0001]. The numerals increase every time a clip is recorded.

  • Page 156: Displaying The Status Screens

    Displays settings related to the configuration of the optional WFT-E6 Wireless File Transmitter and the Wi-Fi network setup. For more details, download the “WFT-E6 Wireless File Transmitter - Guide for Canon Camcorders” (PDF file) from your local Web site and follow the instructions to complete the necessary setup. Ü...
  • Page 157 [Camera] Status Screen 1 ISO speed/Gain increment (A 61) 2 # Iris increment (A 64) 3 Shutter speed increment (A 59) [Assign Button 1/2], [Assign Button 2/2] Status Screen 1 Assignable buttons 1 to 15* (A 99) * Assignable buttons 10 to 15 do not appear in mode only) 4 # Correction for peripheral illumination (A 33)
  • Page 158 Displaying the Status Screens [Audio] Status Screen mode mode 1 XLR terminal recording channel (A 81) 2 Microphone sensitivity (XLR terminal) (A 82) 3 Audio peak limiter (A 82, 83) 4 Microphone mode (MIC terminal) (A 83) 5 Microphone recording level (MIC terminal) (A 83) [Media] Status Screen 1 CF card A 2 CF card B...
  • Page 159 [Video] Status Screen 1 HDMI OUT terminal status 2 HD/SD SDI terminal output setting (A 129) 3 Superimposing onscreen displays to HD output (A 130) 4 SD output setting (A 130) 5 SYNC OUT terminal output status (A 129) [Metadata 1/2] Status Screen 1 User memo file name (A 85) 2 Clip title 3 Camera operator...
  • Page 160 Displaying the Status Screens [Battery/Hour Meter] Status Screen 1 Remaining recording time 2 Remaining recording time indicator 3 Battery life indicator [/ Data 1/3] Status Screen 1 Custom picture file name (A 101) 2 Gamma (A 104) 3 Master pedestal (A 105) 4 Master black RGB levels (A 105) 5 Black gamma settings (level, range and point) (A 105)
  • Page 161 [/ Data 2/3] Status Screen 1 Sharpness settings (level, horizontal detail frequency, horizontal/vertical detail balance, and limit) (A 106) 2 Sharpness settings (select, knee aperture gain and slope) (A 106) 3 Level depend settings (level, slope and offset) (A 107) [/ Data 3/3] Status Screen 1 White balance RGB gain (A 108) 2 Color correction (A 108)

  • Page 162: Troubleshooting

    Troubleshooting Troubleshooting If you have a problem with your camcorder, refer to this section. Consult your dealer or a Canon Service Center if the problem persists. Power source The camcorder will not turn on or it turns off by itself.

  • Page 163: Picture And Sound

    The built-in ND filter is stuck and does not change. - The electronic motor that drives the ND filter may not be working correctly. As an emergency measure, you can operate the ND filter manually (A 172). Eventually, consult a Canon Service Center. Playback Cannot delete a clip.

  • Page 164: Connections With External Devices

    Troubleshooting Video noise appears on screen. - Keep a distance between the camcorder and devices that emit strong electromagnetic fields such as near powerful magnets and motors, MRI machines or high-voltage power lines. Horizontal bands appear on the screen. - This is a phenomenon typical of CMOS image sensors when recording under some types of fluorescent, mercury or sodium lamps.

  • Page 165: List Of Messages

    CF A/CF B Management data is not supported and will be deleted - This message may appear if you insert into the camcorder a CF card that was initialized by another Canon professional camcorder. Check the contents of the CF card.
  • Page 166 When this message appears, select [Yes] and press SET. Fan error - The cooling fan may not be working properly. Consult a Canon Service Center. File name error - The folder and file numbers have reached their maximum value. Set [Other Functions] [Reset] and delete all the photos on the SD card (A 142) or initialize it (A 43).
  • Page 167 System error - Turn off the camcorder and back on again. If this does not solve the problem, there may be a malfunction with the camcorder. Consult a Canon Service Center. This photo cannot be displayed - You may not be able to display photos taken with other devices or image files created or edited on a computer.

  • Page 168: Handling Precautions

    If any of the above should get into the camcorder it may damage the camcorder and/or the lens. Consult a Canon Service Center as soon as possible. • Be careful to avoid dust and dirt particles accumulating on the lens or entering the camcorder. When you finish using the camcorder, make sure to attach the body cap to the lens mount and the lens cap and dust cap to the lens.
  • Page 169 Regarding the use of non-Canon battery packs • We recommend using genuine Canon battery packs bearing the Intelligent System mark. • If you attach to the camcorder battery packs that are not genuine Canon battery packs, the remaining battery time will not be displayed. C (86 °...

  • Page 170: Recording Media

    Recording Media • We recommend backing up the recordings on the recording media onto your computer. Data may be corrupted or lost due to defects or exposure to static electricity. Canon shall not be liable for lost or corrupted data.

  • Page 171: Maintenance/Others

    Maintenance/Others Cleaning Camcorder Body • Use a soft, dry cloth to clean the camcorder body. Never use chemically treated cloths or volatile solvents such as paint thinner. Lens • Remove any dust or dirt particles using a non-aerosol type blower brush. •...

  • Page 172: Using The Camcorder Abroad

    You can use the compact power adapter to operate the camcorder and to charge battery packs in any country with power supply between 100 and 240VAC, 50/60Hz. Consult a Canon Service Center for information on plug adapters for overseas use.

  • Page 173: Optional Accessories

    This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon accessories, although you may request such repairs on a chargeable basis.
  • Page 174 Optional Accessories Charging Times Use the supplied CG-940 Battery Charger to charge battery packs. The charging times given in the following table are approximate and vary according to charging conditions and initial charge of the battery pack. BP-950G BP-955 245 min. 200 min.
  • Page 175 $ Approximate times with the monitor unit attached (LCD screen + viewfinder), SDI output on Type of recording Bit rate NTSC / 24.00P 50 Mbps Recording (maximum) Recording (typical*) Playback 35 Mbps Recording (maximum) Recording (typical*) Playback 25 Mbps Recording (maximum) Recording (typical*) Playback 50 Mbps...
  • Page 176 Optional Accessories This mark identifies genuine Canon video accessories. When you use Canon video equipment, we recommend Canon-brand accessories or products bearing the same mark. CB-920 Car Battery Adapter Use the car battery adapter to charge battery packs on the go. The car battery adapter plugs into your car’s cigarette lighter socket and runs off a...

  • Page 177: Specifications

    • Viewfinder: 1.3 cm (0.52 in.), approx. 1,555,000 dots, 100% coverage • Lens Mount # Canon EF mount compatible with Canon EF lenses (including EF-S lenses) $ PL Lens mount without data interface terminals Lens multiplication factor: approx. 1.53 (for 35mm equivalent focal length) •...
  • Page 178 • Sensor Sensitivity (ISO 640 (0 dB), 2000 lux, 89.9% reflection) ! F9 (1920x1080 at 59.94i) " F10 (1920x1080 at 50.00i) • S/N Ratio (ISO 850, using Canon Log gamma) 54 dB (typical, 1920x1080, ! at 29.97P / " at 25.00P) •...
  • Page 179 Power/Others • Power Supply (rated) 7.4 V DC (battery pack), 8.4 V DC (DC IN) • Power Consumption (recording at 50 Mbps, viewfinder/LCD screen normal brightness, SDI output on) LCD screen and viewfinder: 11.7 W (NTSC, 24.00P recordings), 11.4 W (PAL recordings) Viewfinder only: $ LCD screen and viewfinder: 11.7 W (NTSC, 24.00P recordings), 11.4 W (PAL recordings) Viewfinder only:...
  • Page 180 Specifications Handle Unit Modular unit includes a cold accessory shoe and socket for 0.64 cm (1/4 in.) screws for other accessories. • Weight: Approx. 180 g (6.3 oz.) CA-940 Compact Power Adapter • Power Supply: 100 – 240 V AC, 50/60 Hz •...

  • Page 181: Index

    Camera settings ......111 Canon Log gamma .....109 CF card Inserting .
  • Page 182 Joystick .......29 Joystick guide ......116 Key lock .
  • Page 183 User bit .......76 User memo ......85 Vectorscope .
  • Page 184 B. If the Equipment is defective as a result of leaking batteries, sand, dirt or water damage; C. If defects or damages are caused by the use of parts or supplies (other than those sold by Canon USA) that cause damage to the Equipment or that cause abnormally frequent service calls or service problems;...
  • Page 185 B. If the Equipment is defective as a result of leaking batteries, sand, dirt or water damage; C. If defects or damages are caused by the use of parts or supplies (other than those sold by Canon Canada) that cause damage to the Equipment or that cause abnormally frequent service calls or service problems;...
  • Page 186 MÉXICO CANON MEXICANA, S DE RL DE CV http://www.canon.com.mx 52 (55) 5249-4905 Visit your local Canon Web site to download the latest version of this Instruction Manual. 0157W376 NEW ZEALAND www.canon.co.nz Canon New Zealand Ltd 0800-222-666 (within New Zealand only)

This manual is also suitable for:

Eos c300 pl

Table of Contents