Table of Contents
Advertisement
WARNING
If the product is dropped, suffers heavy impact, or begins
to vibrate abnormally, immediately stop the product and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
TRANSPORTATION AND STORAGE
■
Stop the product, remove the battery, and allow both to
cool before storing or transporting
■
Clean all foreign material from the product. Store it in a
cool, dry, and well-ventilated place that is inaccessible
to children. For extra safety, store the battery separately
from the hedge trimmer. Keep away from corrosive
agents such as garden chemicals and de-icing salts.
Do not store outdoors.
■
Cover the blade with the blade protector before storing
the product or during transportation.
■
For
transportation,
secure
movement or falling to prevent injury to persons or
damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
MAINTENANCE
WARNING
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury, poor performance, and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service, we suggest you bring the
product to your nearest authorised service centre for
repair. When servicing, use only identical replacement
parts.
WARNING
The blades are extremely sharp. To prevent personal
injury, exercise extreme caution when cleaning,
lubricating, and fitting or removing the blade protector.
■
■
■
■
■
■
the
product
against
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■
■
■
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness, and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■
■
■
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor.
Remove the battery before adjusting, maintaining, or
cleaning the product.
You may make adjustments and repairs described in
this manual. For other repairs, contact the authorised
service agent.
After each use, clean the body and handles of the
product with a soft, dry cloth.
After each use, clean the debris from the blades
with a stiff brush, and then carefully apply a rust
preventative lubricant before refitting the blade
protector. The manufacturer recommends you to use
a rust-preventative lubricant spray to apply an even
distribution and reduce the risk of personal injury from
contact with the blades. For information about suitable
spray product, check with an authorised service centre.
Lubricate the blades lightly before use if necessary
using the above method.
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorized service
centre.
Injury caused by the blade
–
Contact with the blades can cause serious injury.
Keep the blade away from yourself and others.
Cover it with the blade protector whenever you are
not cutting.
Injury caused by vibration
–
Always use the right tool for the job, use designated
handles, and restrict working time and exposure.
Hearing injury caused by exposure to noise
–
Wear ear protection and limit exposure.
Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
exposure per day.
3
Advertisement
Table of Contents
