Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch DWW092460B Installation Instructions
Summary of Contents for Bosch DWW092460B Installation Instructions
- Page 1 Operating and installation instructions...
- Page 2 Fig. 1 mind. Abb. 1 ELECTRO mind.
-
Page 3: Appliance Description
Operating Instructions Appliance description Filter grille Operating modes Exhaust-air mode: The extractor-hood fan extracts the kit- chen vapours and conveys them through the grease filter into the atmosphere. The grease filter absorbs the solid particles in the kitchen vapours. The kitchen is kept almost free of grease and odours. -
Page 4: Before Using For The First Time
Before using for the first time Important notes: The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. This extractor hood complies with all relevant safety regulations. -
Page 5: Safety Instructions
Safety instructions Do not use the appliance if damaged. The appliance may be connected to the mains by a qualified technician only. The appliance is not intended for use by young children or infirmed persons without supervision. Young children should be supervised to ensure they do not play with the appliance. -
Page 6: Operating Procedure
Operating procedure The most effective method of removing vapours produced during cooking is to: Switch the ventilator ON as soon as you begin cooking. Switch the ventilator OFF a few minutes after you have finished cooking. Light Off/On Light Off/On Ventilator settings Lighting: The light can be switched on at any... - Page 7 Filters and maintenance Removing and inserting the metal grease filters: 1. Press the catch on the grease filters inwards and fold the filters down. At the same time take hold of the under- side of the grease filters with your other hand.
-
Page 8: Cleaning And Care
Cleaning and care Isolate the extractor hood by pulling out the mains plug or switching off the fuse. Do not clean the extractor hood with abrasive sponges or with cleaning agents which contain sand, soda, acid or chlorine! Clean the extractor hood with a hot soap solution or a mild window cleaner. -
Page 9: Installation Instructions
Installation Instructions: Important information Old appliances are not worthless rubbish. Valuable raw materials can be reclaimed by recycling old appliances. Before disposing of your old appliance, render it unusable. You received your new appliance in a protective shipping carton. All packaging materials are environmentally friendly and recyclable. - Page 10 Prior to installation Exhaust-air mode The exhaust air is discharged upwards through a ventilation shaft or directly through the outside wall into the open. Exhaust air should neither be directed into a smoke or exhaust flue that is currently used for other purposes, nor into a shaft that is used for ventilating rooms in which stoves or fireplaces are also located.
- Page 11 Prior to installation For operating in exhaust-air mode, a one-way flap should be mounted inside the extractor hood unless there is already one fitted in the outlet duct or wall ventilation box. If no one-way flap was enclosed with the hood, it can be obtained from a specialist retailer.
-
Page 12: Electrical Connection
Prior to installation Circulating-air mode With activated carbon filter if exhaust-air mode is not possible. The complete installation set can be obtained from specialist outlets. The corresponding accessory numbers can be found at the end of these operating instructions. Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED IMPORTANT: Fitting a Different Plug:... -
Page 13: Installation
Installation This extractor hood is intended to be mounted onto the kitchen wall. 1. Remove the grease filter (refer to Operating Instructions). 2. Draw a line on the wall from the ceiling to the lower edge of the hood at the centre of the location where the hood is going to be mounted. - Page 14 Installation 08. Insert the other 4 screws with washers. Before the 4 screws are tightened down, align the extractor hood properly. 09. Connect up the air outlet pipe. 10. Connect the hood to the electricity supply. 11. Stainless steel model: Remove the protective film from the two flue ducts.
- Page 15 DHZ 5145 353121...
- Page 16 E-Mail: bosch-infoteam@bshg.com Online-Shop: www.bosch-eshop.com 9000 432 192 Printed in Germany 0209 Es.