400x500mm Working area: Weight (machine): ca 80 kg Size Rack: ca 90x110x160 cm Weight Rack: ca 100 kg Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
If the controller is used within a closed cabinet or room temperatures higher than 25°C, you have to supply additional measures for ventilation. Increased dust load must be prevented by suitable measures. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Do not pull the cables while the machine is under power. First switch off controller and wait for po- tential equalisation. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
/ or English manual coming with the machine into your native language. A declaration of EU conformity is appending. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
S-video-plug door switches. Please control connection of power cable va- cuum cleaner and suction tube. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Page 9
6 bar. Connect the compressor to the pressure redu- cer of the machine. Compare the connection of the spindle with the picture above. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Page 10
Y-axis is the upper cross tra- verses and the Z-axis with the spindle sits on the traverse and moves vertically. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Page 11
Your machine only works correctly with the corres- ponding machine configuration!) or access the ad- vanced features, such as correction factors. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Page 12
0. Then the spindle moves back to the sensor to check Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Page 13
PCB with the values shown in the software !!!l!) Go to to tab Run CNC..Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Page 14
With click on Start the machine again makes a reference run and the processing is carried out in the same manner as with drilling. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Page 17
Now your Software RoutePro3000 is ready to use. Have fun with your CCD and the new software Routero3000! Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Z-axis no longer matches with the position adopted by the program. This could cause damage to the machine table. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Page 20
If you loosen the thumbscrew and slide the aluminium bar to the right, you can move the Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Wipe the steel shafts of the guiding profiles regularly with a lint-free cloth soaked with acid-free oil. Do not forget the shafts on the bottom of the profiles! Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Create a drill file with two or six refer- ence holes. These reference holes form a mirror axis, which is needed to reference the bottom Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
Etched PCBs The board already shows the tracks and pads. The drilling must exactly fit the pads. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...
For appropriate precautions and protective devices, the user has to care himself. Any liability for damage that is caused by the operation in such environment is hereby expressly excluded. Copyright (C) 2014 Bungard Elektronik Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: support@bungard.de...