SmartRG SR505N User Manual
  1. Manuals
  2. Brands
  3. SmartRG Manuals
  4. Network Router
  5. SR505n
  6. User manual

SmartRG SR505N User Manual

4 port vdsl2 11n router
Hide thumbs Also See for SR505N:
Table of Contents

Advertisement

Quick Links

Download this manual
Model:SR505N
User Manual
4 port VDSL2 11n Router
Model:SR505N
V33 User Manual
1

Advertisement

Table of Contents
loading

Related Manuals for SmartRG SR505N

Summary of Contents for SmartRG SR505N

  • Page 1: Table Of Contents

    Model:SR505N User Manual 4 port VDSL2 11n Router Model:SR505N V33 User Manual...

  • Page 2: Table Of Contents

    Model:SR505N Table of Contents UPNP ......................42 TABLE OF CONTENTS ..................1 DNS P ..................... 42 ROXY Device Installation ..................4 .................... 43 NTERFACE ROUP Power on Router ................... 4 ......................45 Factory Reset Button..................5 ....................... 47 ULTICAST Network Connections ..................5 ......................
  • Page 3 V33 User Manual...

  • Page 4: Device Installation

    Device Installation The DSL connects two separate physical interfaces, an ADSL (WAN) and an Ethernet (LAN) interface. Place the Router in a location where it can be connected to the various devices as well as to a power source. The Router should not be located where it will be exposed to moisture or excessive heat.

  • Page 5: Factory Reset Button

    Factory Reset Button The Router may be reset to the original factory default settings by using a ballpoint or paperclip to gently push down the reset button in the following sequence: 1. Press and hold the reset button while the device is powered off. 2.

  • Page 6: Configuration

    Appendix A – Troubleshooting Configuration This section will show you how to configure your new D-Link Router using the web-based configuration utility. Web-based Configuration Utility Connect to the Router The default IP address for ADSL MODEM is: 192.168.1.1; The Subnet Mask is：255.255.255.0. Users can configure ADSL MODEM through an Internet browser.

  • Page 7: Device Info

    Appendix A – Troubleshooting Device Info To access the Device Info window, click either the Device Info or Summary button in the Device Info directory. The following page opens: V33 User Manual...

  • Page 8: Summary

    Appendix A – Troubleshooting Summary To access the Router’s first Summary window, click the Summary button in the Device Info directory. This window displays the current status of your DSL connection, including the software version, LAN IP address, and DNS server address. V33 User Manual...

  • Page 9: Wan

    Appendix A – Troubleshooting To access the WAN Info window, click the WAN button in the Device Info directory. This window displays the current status of your WAN connection. USB Access Methods We can access the USB devices and handle some files with the following steps. We access the USB devices through the samba as the following pictures.
  • Page 10 Appendix A – Troubleshooting Picture 2 We can find the file which name is storage. Enter the file, we find the usb1_1 (As show as the Picture 3). This file is our USB device. V33 User Manual...
  • Page 11 Appendix A – Troubleshooting Picture 3 After accessed the usb1_1, we can do some operating what you want to do. V33 User Manual...

  • Page 12: Route

    Appendix A – Troubleshooting Route To access the Device Info – Route window, click the Route button in the Device Info directory. This read-only window displays routing info. To access the Device Info – ARP window, click the ARP button in the Device Info directory. This read-only window displays Address Resolution Protocol info.

  • Page 13: Advanced Setup

    Appendix A – Troubleshooting Advanced Setup This chapter include the more advanced features used for network management and security as well as administrative tools to manage the Router, view status and other information used to examine performance and for troubleshooting. Layer2 Interface To access the DSL ATM Interface Configuration window, click the ATM Interface button in the Layer2 Interface directory.

  • Page 14: Atm Interface

    Appendix A – Troubleshooting ATM Interface The ATM PVC Configuration window allows you to set up ATM PVC configuration. Enter Virtual Path Identifier,and Virtual Channel Identifier. The VPI and VCI values should be provided by your ISP. This window also allows you to select DSL Link Type, PPPoA、IpoA and EoA (EoA is for PPPoE, IPoE, and Bridge) Use the drop-down menu to select the desired Encapsulation Mode..

  • Page 15: Wan Service

    Appendix A – Troubleshooting WAN Service To access the Wide Area Network (WAN) Service Setup window, click the WAN Service button in the Advanced Setup directory. This window is used to configure the WAN interface. You can add and delete WAN interface on this window. If you are setting up the WAN interface for the first time, click the Add button.
  • Page 16 Appendix A – Troubleshooting This window allows you to select the appropriate connection type. The choices include PPP over ATM (PPPoA), PPP over Ethernet (PPPoE), IP over Ethernet (IpoE), IP over ATM (IPoA), and Bridging. WAN Service Configuration – PPPoE Click the PPP over Ethernet (PPPoE) radio button on this window.
  • Page 17 Appendix A – Troubleshooting WAN Service Configuration – PPPoE This window allows you to set the username and the password for your PPP connection. This information is obtained from your ISP. Additional settings on this window will also depend on your ISP. And You can input ip on this page.
  • Page 18 Appendix A – Troubleshooting WAN Service Configuration – IPoE Click the IP over Ethernet radio button on this window. Click the Next button to continue. V33 User Manual...
  • Page 19 Appendix A – Troubleshooting WAN Service Configuration – IPoE This window allows you to configure the WAN IP settings. This information is obtained from your ISP. Click the Next button to continue. V33 User Manual...
  • Page 20 Appendix A – Troubleshooting WAN Service Configuration – BRIDGING Click the Bridge radio button on this window. Click the Next button to continue. V33 User Manual...
  • Page 21 Appendix A – Troubleshooting WAN Service Configuration – BRIDGING This summary window allows you to confirm the bridging settings you have just made. Click the Apply /Save button to save your new bridging settings and restart the Router. WAN Service Configuration – PPPoA This window allows you to enter service description.
  • Page 22 Appendix A – Troubleshooting WAN Service Configuration – PPPoA This window allows you to set the username and the password for your PPP connection. This information is obtained from your ISP. Additional settings on this window will also depend on your ISP. And You can input ip on this page.
  • Page 23 Appendix A – Troubleshooting WAN Service Configuration – IPoA This window allows you to enter service description. Click the Next button to continue. WAN Service Configuration – IPoA This window allows you to configure the WAN IP settings. This information is obtained from your ISP.

  • Page 24: Lan

    Appendix A – Troubleshooting You can configure the LAN IP address to suit your preference. Many users will find it convenient to use the default settings together with DHCP service to manage the IP settings for their private network. The IP address of the Router is the base address used for DHCP. In order to use the Router for DHCP on your LAN, the IP address pool used for DHCP must be compatible with the IP address of the Router.
  • Page 25 Appendix A – Troubleshooting This window allows you to set up a LAN interface. When you are finished, click the Apply / Save button. V33 User Manual...
  • Page 26 Appendix A – Troubleshooting To access the IPv6 LAN Auto Configuration window, click the IPv6 AutoConfig button in the LAN directory. This window allows you to set up IPv6 LAN Auto Configuration. When you are finished, click the Save /Apply button.

  • Page 27: Port Triggering

    Appendix A – Troubleshooting Port Triggering Some applications such as games, video conferencing, remote access applications and others require that specific ports in the Router's firewall be opened for access by the applications. You can configure the port settings from this screen by selecting an existing application or creating your own (Custom application).

  • Page 28: Dmz Host

    Appendix A – Troubleshooting DMZ Host Since some applications are not compatible with NAT, the Router supports use of a DMZ IP address for a single host on the LAN. This IP address is not protected by NAT and will therefore be visible to agents on the Internet with the right type of software.

  • Page 29: Security

    Appendix A – Troubleshooting Security To access the Security window, click the Security button in the Advanced Setup directory. The Security button appears after configuring WAN interface in PPPoA, PPPoE, IPoE or IPoA. IP Filtering The IP Filtering button appears when configuring WAN interface in PPPoA, PPPoE, IPoE or IPoA. IP Filtering - Outgoing This window allows you to create a filter rule of Outgoing.
  • Page 30 Appendix A – Troubleshooting Enter the information in the section. Explanations of parameters are described below. Click the Apply / Save button to add the entry in the Active Outbound IP Filtering table. IP Filtering – Incoming This window allows you to create a filter rule of Incoming. Click change default policy to change the mode of policy.
  • Page 31 Appendix A – Troubleshooting Enter the information in the section. Explanations of parameters are described below. Click the Apply / Save button to add the entry in the Active Inbound IP Filtering table. V33 User Manual...

  • Page 32: Parental Control

    Appendix A – Troubleshooting Parental Control Use this window to deny access to specified MAC address. If you are setting up the MAC address blocking, click the Add button. MAC address is a specially formatted text string (xx:xx:xx:xx:xx:xx) that uniquely identification of a device. This section will allow users to block devices with certain MAC addresses on the LAN.

  • Page 33: Url Filter

    Appendix A – Troubleshooting URL Filter This window allows you to set up URL Filter on the Router. Choose URL List Type Exclude or Include first and click Add button. Enter the URL address and port number then click Apply / Save to add the entry to the URL filter.

  • Page 34: Quality Of Service

    Appendix A – Troubleshooting Quality of Service QoS or Quality of Service allows your Router to help prioritize the data packet flow in your Router and network. This is very important for time sensitive applications such as VoIP where it may help prevent dropped calls. Large amounts of non-critical data can be scaled so as not to affect these prioritized sensitive real-time programs.

  • Page 35: Queue Config

    Appendix A – Troubleshooting Queue Config Click the Add button to add a QoS Queue Configuration table entry. This window allows you to configure a QoS queue entry and assign it a specific network interface. Click the Apply / Save button to save and activate the filter. V33 User Manual...

  • Page 36: Qos Classification

    Appendix A – Troubleshooting QoS Classification Choose Add or Remove to configure network traffic classes. Use this window to create a traffic class rule to classify the upstream traffic, assign a queue that defines the precedence and the interface, and optionally overwrite the IP header DSCP byte.

  • Page 37: Routing

    Appendix A – Troubleshooting Routing To access the Routing windows, click the Routing button in the Advanced Setup directory. Default Gateway Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.

  • Page 38: Policy Routing

    Appendix A – Troubleshooting Enter the static routing information for an entry to the routing table. Click the Apply / Save button when you are finished. Policy Routing Click the Add button on the Policy Routing Settup window to access the following window displayed on the next page.

  • Page 39: Rip

    Appendix A – Troubleshooting Enter the Policy Routing information.Click the Apply / Save button when you are finished. To activate RIP for the device, select the Enabled radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the 'Enabled' checkbox for the interface.

  • Page 40: Dns

    Appendix A – Troubleshooting To access the DNS windows, click the DNS button in the Advanced Setup directory. The DNS button appears when configuring WAN interface in PPPoA, PPPoE, MER or IPoA. DNS Server Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system.

  • Page 41: Dynamic Dns

    Appendix A – Troubleshooting Dynamic DNS The Router supports Dynamic DNS (Dynamic Domain Name Service). The Dynamic DNS service allows a dynamic public IP address to be associated with a static host name in any of the many domains, allowing access to a specified host from various locations on the Internet.

  • Page 42: Upnp

    Appendix A – Troubleshooting UPNP To access the UPnP Configuration window, click the UPnP button in the Advanced Setup directory. This window allows you to Config UPnP Proxy. Click the Apply / Save button when you are finished. DNS Proxy To access the DNS Proxy Configuration window, click the DNS Proxy button in the Advanced Setup directory.

  • Page 43: Interface Group

    Appendix A – Troubleshooting Interface Group Interface Group supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group.
  • Page 44 Appendix A – Troubleshooting To create a new mapping group, enter Group Name, add interfaces to Grouped Interfaces. Click Apply / Save to save the changes. V33 User Manual...

  • Page 45: Ipsec

    Appendix A – Troubleshooting IPSec To access the IPSec Tunnel Mode Connections window, click the IPSec button in the Advanced Setup directory. This window allows you to configure IPSec. Click Add New Connection to edit IPSec tunnel mode connections from this page V33 User Manual...
  • Page 46 Appendix A – Troubleshooting This window allows you to advanced settings. V33 User Manual...

  • Page 47: Multicast

    Appendix A – Troubleshooting Multicast To access the IGMP Configuration window, click the Multicast button in the Advanced Setup directory. Enter IGMP protocol configuration fields if you want modify default values shown below V33 User Manual...

  • Page 48: Security

    Appendix A – Troubleshooting Security This page allows you to configure security features of the wireless LAN interface. You may setup configuration manually or through WiFi Protcted Setup(WPS) You can select to configure WEP encryption, Shared, 802.1x, WPA, and WPA2 authentication. V33 User Manual...

  • Page 49: Mac Filter

    Appendix A – Troubleshooting MAC Filter This page can help you to allow or deny certain MAC addresses to pass through or block out. Click Add to see the following page. Enter MAC Address and click Apply / Save to add the MAC address to MAC filter.

  • Page 50: Advanced

    Appendix A – Troubleshooting Advanced This page allows you to configure advanced wireless LAN interface. Configuring these settings may increase the performance of your router but if you are not familiar with networking devices and protocols, this section should be left at its default settings. Click Apply / Save to save the settings.

  • Page 51: Station Info

    Appendix A – Troubleshooting Station Info This page shows the authenticated wireless stations and their status. Click Refresh to update the information. V33 User Manual...

  • Page 52: Diagnostics

    Appendix A – Troubleshooting Diagnostics Your modem is capable of testing your DSL connection with access to Diagnostics. This window is used to test connectivity of the Router. V33 User Manual...

  • Page 53: Management

    Appendix A – Troubleshooting Management The Management directory features an array of options designed to help you get the most out of your Router. Settings To access the Settings - Backup window, click the Settings button in the Management directory. This window allows you to backup your DSL Router configurations.

  • Page 54: Internet Time

    Appendix A – Troubleshooting Internet Time To access the Time settings window, click the Internet Time button in the Management directory. This window allows you to set the Router’s time configuration. When you are finished, click the Save/Apply button. V33 User Manual...

  • Page 55: Access Control

    Appendix A – Troubleshooting Access Control To access the Access Control windows, click the Access Control button in the Management directory. Passwords This window allows you to change the password on the Router. When you are finished, click the Save/Apply button. V33 User Manual...

  • Page 56: Reboot

    Appendix A – Troubleshooting Reboot To access this window, click the Reboot button in the Management directory. To save your settings and reboot the system, click the Reboot button. V33 User Manual...

  • Page 57: Troubleshooting

    Appendix A – Troubleshooting Troubleshooting This chapter provides solutions to problems that might occur during the installation and operation of the DSL-STV504. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1.
  • Page 58 Appendix A – Troubleshooting 4. Why can’t I get an Internet connection? For ADSL ISP users, please contact your ISP to make sure the service has been enabled/connected by your ISP and that your ISP username and password are correct. 5.
  • Page 59 FCC Information FCC Caution • Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Table of Contents