SmartRG does not assume any liability arising out of the application or use of any products, or software described herein. Either does it convey any license under its patent rights nor patent rights of others. SmartRG further reserves the right to make changes to any products described herein without notice.
Page 5
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. SmartRG Inc declares that the WR100 is limited to operations on Channels 1 through 11, from 2400 to 2483.5 MHz by specified firmware controlled in the USA.
Learn more at www.SmartRG.com. Purpose & Scope The purpose and scope of this document is to provide the customers of SmartRG with installation, configuration and monitoring information for all CPE platforms. Intended Audience The information in this document is intended for Network Architects, NOC Administrators, Field Service Technicians and other networking professionals responsible for deploying and managing broadband access networks.
LED Status Indicators: Your SmartRG gateway has several indicator lights (LEDs) on its front panel. The number of DSL ports or USB ports may vary from model to model but generally, these indicators are available on all models: POWER LAN 1-4...
Connections: Below is a generic representation of a SmartRG gateway, however your specific model may have greater or fewer ports and con- trols across the back of the unit. Refer to the Quick Start Guide enclosed with your gateway for specifics regarding installation of your particular model.
A stand-alone RJ45 port labeled WAN enables your SmartRG gateway to be hard-wired to another network device with a RJ45/ Ethernet output such as a cable, fiber, or DSL modem. For models with a stand-alone, RJ45, WAN port and a DSL port, the WAN port can be re-purposed to function as an additional LAN port when your internet connection is via DSL.
To manually configure the SmartRG Gateway, access the gateway’s embedded web UI: 1. Attach your computer’s RJ45 connection to any of the SmartRG gateway’s LAN ports (1-4) 2. Configure your computer’s IP interface to acquire an IP address using DHCP (See the IMPORTANT note below for in- structions on logging in to a SmartRG gateway configured for “bridge mode”...
Page 12
For in depth ”how-to” information for specific scenarios, please take advantage of the knowledge base found at our support web site. Ac- cess to this site is restricted to SmartRG customers and partners. Do not attempt to share links to this site with your subscribers.
Reset Statistics button near the bottom of the screen to reset these counters. NOTE: Not all SmartRG gateway models support the SmartPort feature wherein a LAN port can be re-purposed to function as a WAN port (as displayed in the Interface column below note, LAN3, LAN2, LAN1, WAN.) Only models SR5xxn and SR360n support...
WAN Service Device Info -> Statistics -> WAN displays the TX/RX Bytes, Packets, Error and Drops for each WAN interface for your SmartRG Gateway. All WAN interfaces configured for your SmartRG gateway are included. Use the Reset Statistics button near the bottom of the screen to reset these counters.
The Device Info -> Statistics -> xTM displays the ATM/PTM statistics for your SmartRG Gateway. All WAN interfaces configured for your SmartRG gateway are included. Use the Reset button near the bottom of the screen to reset these counters. The individual fields on this screen are defined as follows:...
Device Info -> Statistics -> xDSL displays the DSL statistics for your SmartRG Gateway. All xDSL (VDSL or ADSL) interfaces configured for your SmartRG gateway are included. You are also able to reset these counters by selecting the Reset Statistics button located on the xTM screen as shown below.
Route Device Info -> Route displays the LAN and WAN route table information config- ured in your SmartRG Gateway for both IPv4 and IPv6 implementation. The individual fields on this screen are defined as follows: Field Name Description Destination (Including IPv6 Route) Displays the Destination IP addresses.
Device Info -> ARP displays the host IP addresses and their hardware (MAC) addresses for each LAN Cli- ent connected to the SmartRG Gateway via a LAN Ethernet port or Wireless LAN. The individual fields on this screen are defined as follows:...
Device Info -> DHCP displays a list of locally connected LAN hosts and their DHCP lease status, which are directly connected to the SmartRG Gateway via a LAN Ethernet port or Wireless LAN. The individual fields on this screen are defined as follows:...
VC scheduling is unique from Default Queue’s. PTM Interface The SmartRG gateway’s VDSL2 standards support Packet Transfer Mode (PTM). An alternative to ATM mode, PTM transports packets (IP, PPP, Ethernet, MPLS, and others) over DSL links. Reference the IEEE802.3ah standard for Ethernet in the First Mile (EFM) for additional information.
Page 33
Disables multicast filtering between WAN and LAN (VlanMux) network. MTU size [1370-1492] Edit the Maximum Transmission Units (MTU) for PPP service. Use Base MAC Address Use SmartRG Devices Base (Primary) MAC address. When unchecked a unique MAC per ser- on this WAN interface vice is assigned. ADDITIONAL OPTIONS Enable IPv6 Unnumbered Model WHEN IPV4&IPV6 or IPV6...
Check as applicable for desired rule. MAC Filtering Your SmartRG gateway can block or forward packets based on the originating device. This MAC filtering feature is available only in Bridging mode. For other modes, similar functionality is available via IP Filtering.
Applies the filter to the selected interface(s). Parental Control The Parental Control features of your SmartRG gateway enable restriction of internet access on a LAN host by LAN host basis. This is achieved without the need for client software to be installed on each host.
The stand-alone modem capability does not maintain a unique Allow and Block List for each individual LAN device. Some additional flexibility however is available when your SmartRG gateway is under management of Cisco Prime Home™. Refer to Cisco documentation regarding, “Content Filtering” for instruc- tions.
DSL Bonding NOTE: This feature supported only on SmartRG models SR550n and SR552n. Bonding enables two DSL lines to feed the same modem. Utilize this screen to leverage the bandwidth of both lines. Bonded, they will behave as a single, higher bandwidth connection.
IP Tunnel IP Tunneling is typically used as a means to establish a path between two independent networks. Your SmartRG gateway sup- ports connecting islands of IPv6 networks across the IPv4 internet or IPv4 in IPv6 as well. IPv6inIPv4 After selecting Advanced Setup ->...
DIAGNOSTICS Diagnostics Line performance diagnostic tools are supported by your SmartRG gateway. Three legs of the data path are included in the avail- able tests: LAN connectivity, DSL connectivity and Internet connectivity tests. After selecting Diagnostics -> Diagnostics from the left navigation bar, click the Test button at the bottom of the screen.
TR-069 Client SmartRG gateways support TR-069 based standards for remote management. Utilize this screen to configure the gateway with details about the management ACS (Auto Configuration Server) to which this gateway will be linked.
Update Software Utilize this feature to update the firmware of your SmartRG gateway. Software updates for SmartRG product are available for download by SmartRGs direct customers. Reboot Occasional troubleshooting measures may require that the router be rebooted. The reboot function is located on this screen.
NOTE If you prefer to configure your SmartRG’s WAN interface manually, connect a laptop to any of the LAN ports and follow the instructions in the “Logging in to Your SmartRG Gateway” and “Remote Management” sections. Do not connect the WAN interface cable until after the configuration is completed.
Calix Compass/Consumer Connect ACS solution Affinegy ACS SmartRG gateways have been tested to confirm maximum interoperability with the Affinegy ACS solution. Cisco Prime Home™ ACS SmartRG gateways have a long history of Prime Home™ (formerly ClearVision) ACS interoperability.
Page 116
APPENDIX B: SMARTRG PRODUCT FAMILY – FEATURE COMPARISON MATRIX SmartRG residential gateways combine WAN connectivity with a firewall-protected router and industry-leading TR-069 remote management support. Most variants provide 802.11n Wi-Fi connectivity, as well. See the SmartRG feature details below: Broadband LAN Device...