Advertisement
3.2.2 ASSEMBLY/DISASSEMBLY OF CABINET PARTS AND ELECTRICAL PARTS
Disassembly procedure
STEP
Fig.
PART NAME
No.
No.
[1]
BOTTOM COVER ASSY
3-2-1
[2]
HDD COVER ASSY
3-2-2
[3]
HDD
3-2-3
[4]
HDD CASE ASSY
3-2-4
[5]
OPE.UNIT
3-2-5
[6]
REAR COVER ASSY
3-2-6
[7]
TOP COVER ASSY
3-2-7
[8]
BATT TERMINAL BOARD ASSY
[9]
FRONT ASSY
3-2-8
[10]
MIC
3-2-9
[11]
UPPER ASSY
3-2-10
[12]
STROBE ASSY
3-2-11
[13]
MAIN BOARD ASSY
3-2-12
[14]
SHIELD MAIN ASSY
3-2-13
[15]
OP BLOCK ASSY
3-2-14
3-2-15-1
[16]
OPE. BOARD ASSY
/3-2-15-2
3-2-16-1
[17]
SPEAKER
/3-2-16-2
[18]
MONITOR ASSY
3-2-17
NOTE1:
When removing the BOTTOM COVER ASSY, open and pull
up the COVER (SD).
NOTE2:
Pull out the GRIP BELT from the hook and leave it released
before removing the HDD COVER ASSY.
NOTE3a:
During the procedure, be careful in handling the parts. Pay
special attention not to give any external shock to the HDD.
NOTE3b:
When the HDD is replaced, be sure to refer to REPLACING
HDD in "SECTION2 SPECIFIC SERVICE INSTRUCTIONS"
for the procedure after HDD replacement.
NOTE3c:
Be careful as the GELS at the four corners are easily come
off when the HDD is removed from the main unit. If the
GELS come off, be sure to attach them in the correct direc-
tion shown in the figure.
Attach the GELS with their HOLES on the same side of the
connector.
NOTE3d:
When connecting the FPC to the connector, insert the FPC
straight into the connector. When locking the connector, be
careful not to give so much load that it bends the board.
NOTE3e:
In this procedure, the FPC connected to the HDD connector
is not removed. If the FPC is removed due to broken wire,
be careful in attachment direction. Be sure to connect the
STOPPER side to the HDD.
Pay attention as wrong attachment could damage the HDD.
NOTE3f:
Be careful with the wiring.
POINT
NOTE
4(S1),L1a,3(L1b)
NOTE1
GRIP BELT,2(S2a),2(S2b),
NOTE2
L2a,b,c,d
CN3
NOTE3a,b,c,d,e,f
4(S4a),S4b
-
CN5,S5,L5a,b,c,2(L5d)
NOTE5
S6a,4(S6b),L6
S7a,3(S7b),L7a,b
-
S8,2(L8),CN8
NOTE8
S9a,2(S9b),L9a,b,CN9
NOTE9a,b
2(S10),L10a,b,PLATE(MIC)
NOTE10
CN11,3(S11),3(L11)
NOTE11a,b
CN12,2(S12),L12a,b,2(L12c)
NOTE12a,b
CN13a,b,2(S13)
-
3(S14)
-
3(S15),2(L15)
NOTE15a,b
S16,CN16a,3(S16),
NOTE16a,b,c
2(L16a),L16b,CN16b
SPEACER,2(S17),
NOTE17
L17a,b,c,BKT(SPEAKER)
2(S18),2(L18)
NOTE18
NOTE5:
When attaching, be sure to fit the two positioning studs in the
holes.
NOTE8:
During the procedure, do not touch the terminals (elec-
trodes).
NOTE9a:
When attaching, be careful with the wiring (MIC).
NOTE9b:
Rfer to 3.2.3 ASSEMBLY/DISASSEMBLY OF [9] FRONT
ASSY of FRONT ASSY.
NOTE10:
When attaching, be careful with the wiring (MIC).
NOTE11a:
When removing the screw No.30, open the MONITOR AS-
SY, and then remove the screw paying attention not to dam-
age the screen.
NOTE11b:
When removing, release the connector lock, and then pull
out the FPC together with the UPPER ASSY.
NOTE12a:
During the procedure, be careful to avoid electric shock.
NOTE12b:
When removing, be careful not to break the parts as the
hooks behind the STROBE ASSY make removal difficult.
NOTE15a:
During the procedure, be careful in handling the parts
NOTE15b:
Refer to 3.2.5 DISASSEMBLY OF [15] OP BLOCK ASSY/
CCD BOARD ASSY of OP BLOCK ASSY.
NOTE16a:
When removing, remove the screw No.43 first to release the
FPC, and then pull out the FPC from the connector.
NOTE16b:
During the procedure, be careful not to damage the parts.
NOTE16c:
When attaching, be careful with the wiring.
NOTE17:
When attaching, be careful with the wiring.
NOTE18:
Refer to 3.2.4 DISASSEMBLY OF [18] MONITOR ASSY of
MONITOR ASSY.
Destination of connectors
CN.
CONNECTOR
No.
CN3
MAIN
CN102
CN5
MAIN
CN104
CN8
MAIN
CN103
CN9
MAIN
CN107
CN11
MAIN
CN101
CN12
MAIN
CN109
CN13a MAIN
CN106
CN13b MAIN
CN105
CN16a MAIN
CN402
CN16b MAIN
CN403
PIN
No.
HDD
-
40
OPE.UNIT
-
10
BATT TERMINAL BOARD ASSY -
6
MIC
-
4
OPE
CN401
30
STROBE ASSY
-
14
OP BLOCK ASSY
-
24
CCD
CN802
61
MONITOR
CN7601 22/23
SPEAKER
-
2
(No.YF180)1-7
Advertisement
