Impex MARCY PRO DELUXE CAGE PM-5108 Owner's Manual
  1. Manuals
  2. Brands
  3. Impex Manuals
  4. Fitness Equipment
  5. MARCY PRO DELUXE CAGE PM-5108
  6. Owner's manual

Impex MARCY PRO DELUXE CAGE PM-5108 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PM-5108
Retain This
Manual for
Reference
190205
OWNER'S
MANUAL
MARCY PRO
DELUXE CAGE
PM-5108
IMPEX
2801 S Towne Ave, Pomona, CA 91766
Tel: (800) 999-8899 Fax: (626) 961-9966
www.marcypro.com
support@impex-fitness.com
®
INC.

Advertisement

Table of Contents
loading

Related Manuals for Impex MARCY PRO DELUXE CAGE PM-5108

Summary of Contents for Impex MARCY PRO DELUXE CAGE PM-5108

  • Page 1 PM-5108 Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model PM-5108 Retain This Manual for Reference 190205 ® OWNER'S IMPEX INC. 2801 S Towne Ave, Pomona, CA 91766 MANUAL Tel: (800) 999-8899 Fax: (626) 961-9966 www.marcypro.com support@impex-fitness.com...

  • Page 2: Table Of Contents

    WARRANTY....................…. ORDERING PARTS...................….. BEFORE YOU BEGIN ® Thank you for selecting the MARCY PRO PM-5108 by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.

  • Page 3: Important Safety Notices

    PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS.
  • Page 4 The warning labels shown here have been placed on the Cross Brace, Upper Frame, and Bench Rear Stabilizer. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. ©IMPEX INC. www.marcypro.com...

  • Page 5: Cage Hardware Pack

    CAGE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. ©IMPEX INC. www.marcypro.com...
  • Page 6 CAGE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. ©IMPEX INC. www.marcypro.com...

  • Page 7: Cage Assembly Instructions

    Bracket (#18), two Ø ¾” Washers (#55), and two M10 Aircraft Nuts (#57). H.) Attach the Chin-up Bar (#6) to the Left and Right Vertical Frame. Secure each end with two M10 x 1 5/8” Carriage Bolts (#46), two Ø ¾” Washers (#55), and two M10 Aircraft Nuts (#57). ©IMPEX INC. www.marcypro.com...
  • Page 8 DIAGRAM 1 ©IMPEX INC. www.marcypro.com...
  • Page 9 M10 x 2 3/8” Allen Bolt (#50) and one Ø ¾” Washer (#55). Secure the lower hole with one M10 x 2 ½” carriage Bolt (#45), one Ø ¾” Washer (#55), and one M10 Aircraft Nut (#57). G.) Securely tighten all Nuts and Bolts in Step-1 and Step-2. ©IMPEX INC. www.marcypro.com...
  • Page 10 DIAGRAM 2 ©IMPEX INC. www.marcypro.com...
  • Page 11 CABLE LOOP DIAGRAM ©IMPEX INC. www.marcypro.com...
  • Page 12 E.) Draw the Cable around the Pulley then downward to the triangular bracket on the Sliding Weight Post (#14). Secure the end of Cable to the bracket with one M10 x 1” Allen Bolt (#53), two Ø ¾” Washers (#55), and one M10 Aircraft Nut (#57). ©IMPEX INC. www.marcypro.com...
  • Page 13 DIAGRAM 3 ©IMPEX INC. www.marcypro.com...
  • Page 14 Washers (#55), and one M10 Aircraft Nut (#57). D.) To adjust the tension of the Cable system by moving the lower Pulley position on Double Floating Pulley Brackets. Move up the Pulley to increase the tension, move down the Pulley to loosen the tension. ©IMPEX INC. www.marcypro.com...
  • Page 15 DIAGRAM 4 ©IMPEX INC. www.marcypro.com...
  • Page 16 C.) Connect the Lat Bar (#16) to the Upper Cable (#42) with two Hooks (#58) and the 10-link Chain (#59). D.) Connect the Shiver Bar (#17) to the Lower Cable (#43) with two Hooks(#58) and the 15-link Chain (#60). Replace the Shiver Bar with Single Handle (#39) or Ankle Strap (#40) for various exercises. ©IMPEX INC. www.marcypro.com...
  • Page 17 DIAGRAM 5 ©IMPEX INC. www.marcypro.com...
  • Page 18 PM-5108 WEIGHT RESISTANCE CHART Weight Plate Lat Pull Low Pulley Load even weights on each side of Sliding Weight Post Numbers are approximate. Actual weights may vary. ©IMPEX INC. www.marcypro.com...

  • Page 19: Exploded Diagram

    EXPLODED DIAGRAM ©IMPEX INC. www.marcypro.com...

  • Page 20: Cage Parts List

    45 M10 x 2 ½” Carriage Bolt 46 M10 x 1 5/8” Carriage Bolt 47 M10 x ¾” Carriage Bolt 48 M10 x 3 1/8” Allen Bolt 49 M10 x 2 ¾” Allen Bolt 50 M10 x 2 3/8” Allen Bolt ©IMPEX INC. www.marcypro.com...

  • Page 21: Multi-Purpose Bench Hardware Pack

    MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. ©IMPEX INC. www.marcypro.com...
  • Page 22 MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. ©IMPEX INC. www.marcypro.com...

  • Page 23: Multi-Purpose Bench Assembly Instructions

    D.) Attach the other end of Main Frame to the Rear Stabilizer (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#28), two Ø ¾” Washers (#35), and two M10 Aircraft Nuts (#37). E.) Securely tighten all Nuts and Bolts. DIAGRAM 1 ©IMPEX INC. www.marcypro.com...
  • Page 24 Securely tighten Nut and Bolt in A & B. C.) Attach two Seat Brackets (#4) to the Main Frame. Secure each Seat Bracket with one M8 x 2 ¾” Allen Bolt (#27), two Ø 5/8” Washers (#36), and one M8 Aircraft Nut (#33). DIAGRAM 2 ©IMPEX INC. www.marcypro.com...
  • Page 25 M8 x 1 5/8” Allen Bolts (#32) and  5/8” Washers (#36). B.) Place the Seat Pad (#10) onto the two Seat Brackets (#4). Secure it with four M8 x 1 1/8” Allen Bolts (#31) and  5/8” Washers (#36). DIAGRAM 3 ©IMPEX INC. www.marcypro.com...
  • Page 26 Push six Foam rolls (#14) onto the Tubes from both ends. Plug six Foam Roll End Caps (#16) into the Ends. D.) Attach an Olympic Sleeve (#15) onto the Leg Developer Weight Post. Attach a Spring Clip (#21) to the Olympic Sleeve. DIAGRAM 4 ©IMPEX INC. www.marcypro.com...

  • Page 27: Exploded Diagram

    ©IMPEX INC. www.marcypro.com...

  • Page 28: Multi-Purpose Bench Parts List

    M8 x 1 1/8” Allen Bolt M8 x 1 5/8” Allen Bolt M8 Aircraft Nut Ø 1” End Cap Ø ¾” Washer Ø 5/8” Washer M10 Aircraft Nut Ø 1” x Ø 3/8” Washer 6# Allen Wrench (Tool) 5# Allen Wrench (Tool) ©IMPEX INC. www.marcypro.com...

  • Page 29: Warranty

    IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.

This manual is also suitable for:

Marcy pro pm-5108

Table of Contents