Page 1
PLASMA DISPLAY TV Chassis : F34B(N_HD_R1)_Lily Model : HPT5044X/XAA SERVICE Manual PLASMA DISPLAY TV CONTENTS 1. Precaution 2. Product Specification 3. Disassembly & Reassembly 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram 7. Schematic Diagram HP-T5044 Refer to the service manual in the GSPN (see the rear cover) for the more information.
When Check the AC power cord for possible damages. Keep voltage exceeds the specified limits, check each special the part or the lead away from any heat-emitting part. materials. Samsung Electronics...
Page 5
Critical safety parts should be bracketed with ( Use only regular parts for replacements (in particular, flame resistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire. Samsung Electronics...
AC source and turn the switch on. Connect the insu- lating resistance meter (500v) to the AC plug blade. The insulating resistance between the blade of the AC plug and that of the conductive material should be more than 1 ㏁. Samsung Electronics...
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
5. Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric shock. Samsung Electronics...
2. Product Specification 2-1 Product Specification Features Block Specification Major IC Remark NTSC/VSB/QAM Tuner Digital/Analog (DTV Built In) S5H2111X01(Lake1) PDP Module Samsung SDI W2A Module 42"HD/50"HD New Module Samsung/Dong-yang electro Power mechanics SMPS NTSC 3.58, ATSC HDMI Lake1 Video DNIe(FBE2)
Page 11
New Features explanation ■ ■ - Anynet+ : Anynet+ is an AV network system that enables you to control all connected Samsung AV devices with your Samsung TV's remote. To directly connect to TV Connect the [HDMI 1], [HDMI 2]...
PDP TV PDP TV Built-In Tuner ○ ○ Resolution 1365 x 768 1024 x 768 PDP Module Samsung SDI V5.1 Basic Screen Size 50" 42" Picture ratio 16 : 9 16 : 9 Dimensions (WxHxD) 1227.1 x 844.8 x 340 mm 41.5 x 28 x 3.8 inches...
3-1-2 Separation of ASSY PCB MISC-MAIN Part Name Description Description Photo Main ① Detach all connectors from the Main Board Board. ② Remove 4 screws. : PH,+,WWP,M3,L8,NI PLT ③ Remove the Main Board. Samsung Electronics...
Page 17
Description Photo Wall ① Remove 8 screws. ( Bracket : BH,+,S,M4,L10,ZPC(BLK) ② Remove 8 screws. ( : BH,+,B,M4,L12,ZPC(BLK) ③ Remove Wall Bracket. : Please lay the PDP panel face down on a soft surface when separating front cover. Samsung Electronics...
Page 18
② Remove 8 screws. : PH,+,WWP,M3,L8,NI PLT ③ Remove the SMPS. : Wear gloves when handling the power board as there may be some remaining electrical charge in the capacitor. Specifically, avoid touching any part of the capacitor. Samsung Electronics...
Page 19
3-1-9 Separation of ASSY PDP MODULE P-LOGIC MAIN BOARD Part Name Description Description Photo 50" ① Detach all connectors from the Logic Logic Main Board. Board ② Remove 4 screws. : WSP,PH,+,M3,L8,NI PLT ③ Remove the Logic Main Board. Samsung Electronics...
Page 20
X-Board, press the upper and the lower sides of the connector. 42" ① Remove 4 screws. X-Main : PH,+,WWP,M3,L8,NI PLT Board ② Remove the X-Main Board. 50" ① Remove 4 screws. X-Main : PH,+,WWP,M3,L8,NI PLT Board ② Remove the X-Main Board. Samsung Electronics...
Page 21
Flat Cable ① Detach the 6 scan board connectors from the panel by pulling the holder from both the top and bottom ends. 42" ① Remove 3 screws. Y-Scan : PH,+,WWP,M3,L8,NI PLT Board 50" ① Remove 5 screws. Y-Scan : PH,+,WWP,M3,L8,NI PLT Board Samsung Electronics...
Page 22
Description Photo 42" ① Remove 4 screws. Y-Main : PH,+,WWP,M3,L8,NI PLT Board ② Detach all connectors from the Y-Main Board. 50" ① Remove 4 screws. Y-Main : PH,+,WWP,M3,L8,NI PLT Board ② Detach all connectors from the Y-Main Board. Samsung Electronics...
Page 23
② Remove 12 screws. : PH,+,WWP,M3,L8,NI PLT ③ Remove the E-Board and F-Board. 50" ① Detach the all connectors from the Buffer buffer board. Board ② Remove 14 screws. : PH,+,WWP,M3,L8,NI PLT ③ Remove the E-Board and F-Board. Samsung Electronics...
Page 24
: BH,+,B,M4,L3,ZPC(BLK) ② Remove 4 screws. ( : BH,+,S,M4,L10,ZPC(BLK) ③ Remove the Side Panel Brackets. 3-1-14 Separation of ASSY PCB FUNCTION Part Name Description Description Photo Function ① Remove 2 screws. Board : BH,+,B,M4,L3,ZPC(BLK) ② Remove the Function Board. Samsung Electronics...
- Check to see if the cables are connected according to the connection diagram. 2. Check the power input to the Main Board. 3. Check the voltage in and out between the SMPS ↔ Main Board, between the SMPS ↔ X, Y Main Board, and between the Logic Boards. Samsung Electronics...
Page 27
Is the Fuse (F801S) of the SMPS ① Replace Fuse (F801S) Power Input Part blown? SMPS CN801 ② Pin 3 : STB 5V Replace the SMPS Pin 2 PS-ON : Check to see if it is 0V Replace the Main Board Samsung Electronics...
Page 28
MAIN SMPS, CN4701 OF THE X MAIN BOARD, AND CN5707 OF THE Y MAIN BOARD, A SPARK MAY BE Caution GENERATED BY THE ELECTRIC CHARGE OF THE HIGH CAPACITY CAPACITOR. THEREFORE, WAIT SOME TIME AFTER DISCONNECTING THE POWER CORD FROM THE UNIT. Samsung Electronics...
Page 29
MAIN SMPS, CN4701 OF THE X MAIN BOARD, AND CN5707 OF THE Y MAIN BOARD, A SPARK MAY BE Caution GENERATED BY THE ELECTRIC CHARGE OF THE HIGH CAPACITY CAPACITOR. THEREFORE, WAIT SOME TIME AFTER DISCONNECTING THE POWER CORD FROM THE UNIT. Samsung Electronics...
Page 30
Is the output voltage of SMPS normal? ② (CN801 #13) Replace the SMPS Is the speaker output terminal of the Main Board normal? Replace the Main Board ③ Replace the Speaker Samsung Electronics...
Page 31
- Check the CVBS cable connection. - Check the power input of the Main board. Troubleshooting Procedures Is the antenna connection setting properly configured? Configure properly ① Check CN101 pin2 for +5V Replace the SMPS Replace the Main Board Samsung Electronics...
Page 32
Check the U101, D108 Normal Abnormal Check the U201, Q203, Q204 Normal Abnormal Check the U501 Abnormal Check the U601 Multi Normal Abnormal Check the Q401, Q402 Normal Check the Other board (Image Board or Driver Board) or Cable. Samsung Electronics...
Page 33
Some horizontal lines appear to be linked on screen Scan Buffer, FPC of X/Y Address Open Some vertical lines don't exist on screen Logic Main, Logic Buffer, TCP Address Short Some vertical lines appear to be linked on screen Logic Main, Logic Buffer, TCP Samsung Electronics...
Page 34
F5004 for VCC F4004 for VDD F5005 for OUT_L F4005 for Ve Q4002~Q4003 SHORT SHORT Q5009~Q5021 FET/ Q4011~Q4016 FET/ D5005, D5007 Replace the Board Replace the Board DIODE D4004 DIODE D5008 D4006~D4008 Y-MAIN X-MAIN Normal State Normal State Samsung Electronics...
Page 35
FUSE Replace the Board FUSE Replace the Board F5004 for VCC F4004 for VDD F5005 for OUT_L F4005 for Ve SHORT SHORT Q4002~Q4003 Q5009~Q5021 Replace the Board Replace the Board Q4011~Q4016 Y-MAIN X-MAIN Normal State Normal State 4-10 Samsung Electronics...
Page 36
④ Sustain Short (some horizontal lines appear to be linked on Video) [ Y-FPC ] Sustain Short (Discharging in unwanted Scan line) After Changing Y-buffer, Replace the Panel recheck the status There is a defect on the FPC Done (Defect is from Y-buffer) Samsung Electronics 4-11...
Page 37
Buffer Board and the Logic Main address data output section. Check the FFC connection status Check the detailed waveform Replace Logic Main / and control the signal waveform Address Buffer (E or F) / DONE Replace the Panel 4-12 Samsung Electronics...
Page 38
- Check the version of each program - Replace the Main board A blank upper (or lower) block Upper/Lower Y Buffer defect appears on the screen. - Replace the corresponding upper/lower buffers (E, F) Samsung Electronics 4-13...
Page 39
- Adjust the SMPS voltage according to the voltage printed on the module label Dim screen (blurred in red) X-Main board defect - Replace the X-Main board A blank screen appears - Replace the Y-Main board 4-14 Samsung Electronics...
Page 40
No Power, Abnormal screen for each input source, PIP screen trouble, Sound trouble ASSY BOARD P-FUNCTION The side function key does not work properly 10 ASSY BOARD P-POWER&IR The remote control does not work properly, the LED does not work properly. Samsung Electronics 4-15...
① Write down the value of HDMI White Balance of Factory Mode before replacing Board. ② PDP Option of Factory Mode → set the Factory Data Type item as the suitable value of relevant model. ③ Set the value of HDMI White Balance with the value written down before. 4-16 Samsung Electronics...
Page 42
※ If you have adjusted the settings in Service Mode, you have to reset the product. ※ If you exit Service Mode without reset, DNIe vlaue keeps Off regardless of setting up the user. Samsung Electronics 4-17...
Page 43
1200 1200 1200 HDMI Mode Ident Auto Auto Auto Auto Auto Select FBE FBE2X FBE2X FBE2X FBE2X FBE2X WM_Calibration SVP Caption level No MGT Case Hotel Mode * Spread Spectrum Item Data SSC Range SSC RESET SEL 4-18 Samsung Electronics...
Page 46
③ UV Delay Item Range AV/S-video Component HD HDMI U Delay V Delay ④ PGA Item Range AV/S-video Component HD HDMI TCD3_Contrast TCD3_Bright TCD3_YC_Delay ANALOG_Y_Offset ANALOG_PB_Offset ANALOG_PR_Offset ANALOG_Y_Gain ANALOG_PB_Gain ANALOG_PR_Gain Samsung Electronics 4-21...
Page 48
M-Skin-Tv M-Au Sub color MW_Skin Tu MW_Skin Tv M-Wi Sub color 7. MSP44XX Item Range AV/S-video Component HD HDMI FM_Precale Melody Volume SpdifDelay InternalDelayDtv InternalDelayAnalog Carrier Mute Pilot High Pilot Low Scart1 Out Volume Scart2 Out Volume Samsung Electronics 4-23...
Page 50
No Info No Info No Info No Info Panel Version Logic SW Version 61128 61128 61128 61128 61128 Factory Update Factory Data Type 50SPuu 50SPuu 50SPuu 50SPuu 50SPuu CDC_SW CDC_STRENG_TH BRE_SE PANEL TEMP 15. RESET 16. 10W, NONE Samsung Electronics 4-25...
Page 51
Perform in NTSC B&W Pattern #24 Lattice Component IN (Model_#6) Perform in 720p B&W Pattern #24 Lattice Perform in VESA XGA (1024x768) PC Analog IN (Model_#21) Lattice B&W Pattern #24 HDMI IN Perform in 720p B&W Pattern #24 Lattice <Table 1> 4-26 Samsung Electronics...
Page 52
6) In "HDMI Calibration Off" status, press the "▶" key to perform Calibration. 7) When Calibration is complete, it returns to the high-level menu. 8) You can see the change of the "HDMI Calibration" status from Failure to Success. Samsung Electronics 4-27...
Page 53
3. Pattern : Pattern #92 4. Use Equipment : MIK-7256 (MSPG925L) ( SAMSUNG WHITE BALANCE Adjustment PATTERN with FPD ) 5. Work order ① Connect HDMI (DVI) output terminal of MIK-7256 (MSPG925L) to the HDMI input in main set ② Set the input to HDMI mode ③...
Page 55
ASSY PDP MODULE P-Y-MAIN SCAN BUFFER ASSY PDP MODULE P-ADDRESS E BUFFER ASSY PDP MODULE P-ADDRESS F BUFFER ※ When replacing the SMPS or PDP panel, you have to check the voltage printed on the panel sticker and adjust it. 4-30 Samsung Electronics...
Page 56
(If you do not adjust the voltage, an abnormal discharge symptom may appear.) Value Board Adjustment Vset SMPS Vscan -190 SMPS Voltage Label 2. A point of adjusting SMPS-MAIN voltage. Vs Adjustment Vs Test point Va Test point Va Adjustment Samsung Electronics 4-31...
Page 57
Troubleshooting Y-RR and Y-FR controls ■ ■ Test Point Set the main reset (rising : 60usec, falling : 80usec) by change the value of variable resistor. 60usec 80usec Rising ramp variable resistor Falling ramp variable resistor 4-32 Samsung Electronics...
It takes about 30 sec. (Warning: Don't remove USB flash driver during upgrade.) ⑨ The banner OSD "Upgrade is completed" is displayed when the upgrade is completed. ⑩ Remove the USB flash driver from PDP TV and check the program version. Samsung Electronics 4-33...
Page 59
② Place the cursor over the "On" of "Function Help", and press the "Info" key on the remote control ③ The version of the program is displayed at the bottom of the Menu screen MAIN PROGRAM VERSION MICOM VERSION 2. How to check Program Version on factory mode. MAIN PROGRAM VERSION MICOM VERSION 4-34 Samsung Electronics...
Page 67
KEY_INPUT2 5.3V 5.3V LED_CTRL ⑨ ⑩ ⑪ 401(MAIN B'D) N1802P(MAIN B'D) CN800(SMPS) ↔ ↔ ↔ SPEAKER FUNCTION AC INLET Pin No. Signal Pin No. Signal Pin No. Signal R+_OUT KEY_INPUT1 AC Neutral R-_OUT KEY_INPUT2 L+_OUT AC Live L-_OUT Samsung Electronics...
Page 68
CN1404 Video signal input connect form Side AV ass'y CN1606 Power SW input connect on Main Board CN1203 Speak out connect on Main Board Function input(source,ch up/down...) connect to Main board Power SW input connect to Main Board Samsung Electronics...
Connects to the Y terminal block, 1) provides maintaining voltage waveform (including ERC), 2) provides Y Rising, Falling Ramp waveforms, and 3) maintains the Vscan bias. ■ Address Buffer Board It delivers the data signal and control signal to the TCP. Samsung Electronics...
Page 72
Schematic Diagram 7-2 Schematic Diagram 7-2-1 MAIN POWER BLOCK This Document can not be used without Samsung’s authorization. Power " 2 " 2 , " , " ) " Samsung Electronics...
Page 73
Schematic Diagram 7-2-2 STANDBY MICOM (WT61P6) This Document can not be used without Samsung’s authorization. Power & c t i Samsung Electronics...
Page 74
Schematic Diagram 7-2-3 SOUND PROCESSOR (MSP4450) This Document can not be used without Samsung’s authorization. Power Samsung Electronics...
Page 75
Schematic Diagram 7-2-4 SOUND AMP (NTP3000) & POP SOLUTION This Document can not be used without Samsung’s authorization. Power Samsung Electronics...
Page 76
Schematic Diagram 7-2-5 NIM TUNER 1410 This Document can not be used without Samsung’s authorization. Power Samsung Electronics...
Page 77
Schematic Diagram 7-2-6 BACK AV IN/OUT This Document can not be used without Samsung’s authorization. Power Samsung Electronics...
Page 78
Schematic Diagram 7-2-7 HDMI SWITCH & PC & HDMI INPUT This Document can not be used without Samsung’s authorization. Power Samsung Electronics...
Page 79
Schematic Diagram 7-2-8 SVP-PX POWER BLOCK This Document can not be used without Samsung’s authorization. Power 7-10 Samsung Electronics...
Page 80
Schematic Diagram 7-2-9 VIDEO DECODER & SCALER (SVP-PX) This Document can not be used without Samsung’s authorization. Power > - l a i n i l & n i l Samsung Electronics 7-11...
Page 81
Schematic Diagram 7-2-10 SVP-PX DDR MEMORY This Document can not be used without Samsung’s authorization. Power 7-12 Samsung Electronics...
Page 82
Schematic Diagram 7-2-11 LVDS & PWM CONTROL & PANEL I/F This Document can not be used without Samsung’s authorization. Power Samsung Electronics 7-13...
Page 83
Schematic Diagram 7-2-12 LAKE (I2C & GPIO & USB & UART & INTERRUPT) This Document can not be used without Samsung’s authorization. Power 7-14 Samsung Electronics...
Page 84
Schematic Diagram 7-2-13 LAKE (I2S IN/OUT & TS-INPUT & YCbCr OUTPUT) This Document can not be used without Samsung’s authorization. Power Samsung Electronics 7-15...
Page 85
Schematic Diagram 7-2-14 LAKE (DDR MEMORY) This Document can not be used without Samsung’s authorization. Power 7-16 Samsung Electronics...
Page 86
Schematic Diagram 7-2-15 LAKE (STATIC MEMORY & DEBUG) This Document can not be used without Samsung’s authorization. Power Samsung Electronics 7-17...
Page 87
Schematic Diagram 7-2-16 LAKE (POWER BLOCK) This Document can not be used without Samsung’s authorization. Power 7-18 Samsung Electronics...
Page 88
Schematic Diagram 7-2-17 SUB FUCNTION This Document can not be used without Samsung’s authorization. Power Samsung Electronics 7-19...