Table of Contents
Related Manuals for Hitachi CP-RX80W
Summary of Contents for Hitachi CP-RX80W
- Page 1 trusted dependable most name projector lamp sales. http://www.myprojectorlamps.com http://www.myprojectorlamps.ca http://www.myprojectorlamps.eu The following projector manual has not been modified or altered in any way.
-
Page 2: About This Manual
Projector CP-RX80 User’s Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read all manuals for this product. Be sure to read “Safety Guide” fi rst. After reading them, store them in a safe place for future reference. -
Page 3: Table Of Contents
Contents Contents Contents About this manual ... 1 PICTURE menu ... . 26 Contents ....2 RIGHTNESS ONTRAST AMMA... -
Page 4: Projector Features
Projector features / Preparations Projector features Projector features This projector realizes the large projection image, even if in a small space. Preparations Preparations Checking the contents of package Your projector should come with the items MY SOURCE/ VIDEO COMPUTER DOC.CAMERA shown below. -
Page 5: Part Names
Part names Part names Part names Projector HOT! (2) (3) (1) Lamp cover ( The lamp unit is inside. (2) Focus ring ( (3) Zoom ring ( (11) (4) Control panel ( (5) Elevator buttons (x 2) ( (6) Elevator feet (x 2) ( (10) (7) Remote sensor ( (8) Lens (... -
Page 6: Control Panel
Part names Control panel (1) STANDBY/ON button ( (2) INPUT button ( 16, 22) (3) MENU button ( It consists of four cursor buttons. 11, 14, 58) (4) POWER indicator ( (5) TEMP indicator ( (6) LAMP indicator ( Rear panel (1) AUDIO OUT port (5) Shutdown switch ( (2) AUDIO IN port... -
Page 7: Remote Control
Part names Remote control (1) VIDEO button ( (10) (2) COMPUTER button ( (3) SEARCH button ( MY SOURCE/ COMPUTER VIDEO DOC.CAMERA (4) STANDBY/ON button ( AUTO ASPECT SEARCH BLANK (14) (5) ASPECT button ( MAGNIFY FREEZE PAGE VOLUME (12) (6) AUTO button ( DOWN (11) -
Page 8: Setting Up
Setting up Setting up Setting up Install the projector according to the environment and manner the projector will be used in. Arrangement Refer to the illustrations and tables below to determine screen size and projection distance. The values shown in the table are calculated for a full size screen: 1024 x 768 a Screen size (diagonal) b Projection distance (±10%) c1 , c2 Screen height (±10%) - Page 9 Setting up Arrangement (continued) WARNING ►Place the projector in a stable horizontal position. If the projector falls or is knocked over, it could cause injury and/or damage to the projector. Using a damaged projector could then result in fi re and/or electric shock.
-
Page 10: Connecting Your Devices
Setting up Connecting your devices Be sure to read the manuals for devices before connecting them to the projector. 追 Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them. - Page 11 Setting up Connecting your devices (continued) NOTE • Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.
-
Page 12: Connecting Power Supply
Setting up Connecting power supply Put the connector of the power cord into the AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange. -
Page 13: Remote Control
Holding the hook part of the battery cover, remove it. Align and insert the two AA batteries (HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control. Replace the battery cover in the direction of the arrow and snap it back into place. -
Page 14: About The Remote Control Signal
Remote control About the remote control signal The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. Approx. The sensor senses the signal within the following range 30º 30º when the sensor is active: 60 degrees (30 degrees to the left and right of the sensor) within 3 meters about. -
Page 15: Power On/Off
Power on/off Power on/off Power on/off STANDBY/ON button Turning on the power POWER indicator Make sure that the power cord is fi rmly and correctly connected to the projector and the outlet. Make sure that the POWER indicator is 58). steady orange ( MY SOURCE/ VIDEO... -
Page 16: Operating
Operating Operating Operating Adjusting the volume VOLUME +/- button Use the VOLUME +/VOLUME - buttons to adjust the volume. MY SOURCE/ A dialog will appear on the screen to aid you in adjusting the VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK volume. -
Page 17: Selecting An Input Signal
Operating Selecting an input signal Press INPUT button on the projector. INPUT button Each time you press the button, the projector switches its input port from the current port as below. COMPUTER IN S-VIDEO VIDEO ● While ON is selected for AUTO SEARCH item in OPTION 42), the projector will keep checking the ports in menu ( above order repeatedly till an input signal is detected. -
Page 18: Searching An Input Signal
Operating Searching an input signal SEARCH button Press SEARCH button on the remote control. The projector will start to check its input ports as below in MY SOURCE/ VIDEO COMPUTER DOC.CAMERA order to fi nd any input signals. ASPECT AUTO SEARCH BLANK When an input is found, the projector will stop searching... -
Page 19: Adjusting The Projector's Elevator
Operating Adjusting the projector’s elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the 14°... -
Page 20: Using The Automatic Adjustment Feature
Operating Using the automatic adjustment feature AUTO button Press AUTO button on the remote control. Pressing this button performs the following. MY SOURCE/ For a computer signal VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK The vertical position, the horizontal position and the horizontal MAGNIFY FREEZE PAGE... -
Page 21: Correcting The Keystone Distortions
Operating Correcting the keystone distortions KEYSTONE button Press KEYSTONE button on the remote MY SOURCE/ control. A dialog will appear on the screen to COMPUTER VIDEO DOC.CAMERA ASPECT AUTO SEARCH BLANK aid you in correcting the distortion. FREEZE PAGE VOLUME MAGNIFY Use the ◄/►... -
Page 22: Temporarily Freezing The Screen
Operating Temporarily freezing the screen FREEZE button Press the FREEZE button on the remote control. The “FREEZE” indication will appear on the screen (however, MY SOURCE/ VIDEO COMPUTER DOC.CAMERA the indication will not appear when the OFF is selected for AUTO ASPECT SEARCH... -
Page 23: Using The Menu Function
Operating Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, SECURITY and EASY MENU. EASY MENU consists of functions often used, and the other menus are classifi ed into each purpose and brought together as the ADVANCED MENU. Each of these menus is operated using the same methods. - Page 24 Operating Using the menu function (continued) To close the MENU, press the MENU button again or select EXIT and press the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds. ●...
-
Page 25: Easy Menu
EASY MENU EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table. Item Description Using the ◄/► buttons switches the mode for aspect ratio. ASPECT 29 ). - Page 26 EASY MENU Item Description Using the ◄/► buttons turns off/on the eco mode. ECO MODE See the ECO MODE item in SETUP menu ( 34 ). Using the ◄/► buttons switches the mode for mirror status. MIRROR 34 ). See the MIRROR item in SETUP menu ( Performing this item resets all of the EASY MENU items except the FILTER TIME and LANGUAGE.
-
Page 27: Picture Menu
PICTURE menu PICTURE menu PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. -
Page 28: Color Temp , C
PICTURE menu Item Description Using the ▲/▼ buttons switches the color temperature mode. 1 HIGH 1 CUSTOM 2 MID 2 CUSTOM 6 CUSTOM 3 LOW 6 Hi-BRIGHT-3 3 CUSTOM 5 CUSTOM 5 Hi-BRIGHT-2 4 CUSTOM 4 Hi-BRIGHT-1 To adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the ►... -
Page 29: My Memory
PICTURE menu Item Description This projector has 4 memories for adjustment data (for all the items of the PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each function. SAVE-1 SAVE-2 SAVE-3 SAVE-4 LOAD-4 LOAD-3... -
Page 30: Image Menu
IMAGE menu IMAGE menu IMAGE menu From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. - Page 31 IMAGE menu Item Description Using the ◄/► buttons adjusts the horizontal phase to eliminate fl icker. Right Left H PHASE • This item can be selected only for a computer signal or a component video signal. Using the ◄/► buttons adjusts the horizontal size. Small Large •...
-
Page 32: Input Menu
INPUT menu INPUT menu INPUT menu From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. -
Page 33: Video Format , C
INPUT menu Item Description The video format for S-VIDEO port and VIDEO port can be set. 追 (1) Use the ▲/▼ buttons to select the input port. S-VIDEO VIDEO (2) Using the ◄/► buttons switches the mode for video format. VIDEO FORMAT AUTO NTSC... -
Page 34: Resolution
INPUT menu Item Description The resolution for the COMPUTER IN input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed. -
Page 35: Setup Menu
SETUP menu SETUP menu SETUP menu From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. -
Page 36: Standby Mode , M
SETUP menu Item Description Using ▲/▼ buttons switches the standby mode setting between 変 NORMAL and SAVING. NORMAL SAVING When SAVING is selected, the power consumption in the standby STANDBY MODE mode is lowered with some functional restriction as below: •... -
Page 37: Audio Menu
AUDIO menu AUDIO menu AUDIO menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table. -
Page 38: Screen Menu
SCREEN menu SCREEN menu SCREEN menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. - Page 39 SCREEN menu Item Description This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.
- Page 40 SCREEN menu Item Description Using the ▲/▼ buttons turns on/off the MyScreen lock function. When the ON is selected, the item MyScreen is locked. Use this MyScreen Lock function for protecting the current MyScreen. • This function cannot be selected when the ON is selected to the 48 ).
- Page 41 SCREEN menu Item Description Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE NAME menu will be displayed. (2) Use the ▲/▼...
- Page 42 SCREEN menu Item Description The C.C. is the function that displays a transcript or dialog of the audio portion of a video, fi les or other presentation or other relevant sounds. It is required to have NTSC format video or 480i@60 format component video source supporting C.C.
-
Page 43: Option Menu
OPTION menu OPTION menu OPTION menu From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. -
Page 44: Auto Off , L
OPTION menu Item Description Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) Short (min. 0 minute = DISABLE) When the time is set to 0, the projector is not turned off automatically. AUTO OFF When the time is set to 1 to 99, and when the passed time with no- signal or an unsuitable signal reaches at the set time, the projector... - Page 45 OPTION menu Item Description This item is to assign one of the following functions to MY BUTTON 1/2 on the remote control ( 6 ). (1) Use the ▲/▼ buttons on the MY BUTTON menu to select a MY BUTTON - (1/2) and press the ► button to display the MY BUTTON setup dialog.
- Page 46 OPTION menu Item Description Selecting this item displays the SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item. FAN SPEED Using the ▲/▼ buttons switches the rotation speed of the cooling fans.
- Page 47 OPTION menu Item Description KEY LOCK Using the ▲/▼ buttons turns on/off the key lock feature. When ON is selected, the buttons on the projector except the STANDBY/ON 変 button are locked. • Please use this function to prevent tampering or accidental operation.
-
Page 48: Security Menu
SECURITY menu SECURITY menu SECURITY menu This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed. To use SECURITY menu: User registration is required before using the security functions. Enter the SECURITY menu 1. -
Page 49: Myscreen Password
SECURITY menu Item Description The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten. 1 Turning on the MyScreen PASSWORD 1-1 Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ►... - Page 50 SECURITY menu Item Description PIN LOCK is a function which prevents the projector from being used unless a registered Code is input. 1 Turning on the PIN LOCK 1-1 Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/ off menu.
-
Page 51: My Text Password
SECURITY menu Item Description The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT; • The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting. •... -
Page 52: My Text Writing
SECURITY menu Item Description (1) Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT DISPLAY and press the ► button to display the MY TEXT DISPLAY on/off menu. (2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select on or off. -
Page 53: Maintenance
Maintenance Maintenance Maintenance Replacing the lamp A lamp has fi nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. - Page 54 Maintenance Replacing the lamp (continued) Lamp warning HIGH TEMPERATURE HIGH PRESSURE HIGH VOLTAGE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
-
Page 55: Cleaning And Replacing The Air Fi Lter
Maintenance Cleaning and replacing the air fi lter Please check and clean the air fi lter periodically. When the indicators or a message prompts you to clean the air fi lter, comply with it as soon as possible. Replace the air fi lter when it is damaged or heavily soiled. To prepare a new air fi... - Page 56 Maintenance Cleaning and replacing the air fi lter (continued) WARNING ►Before taking care of the air fi lter, make sure the power cable is not plugged in, then allow the projector to cool suffi ciently. Taking care of the air fi lter in a high temperature state of the projector could cause an electric shock, a burn or malfunction to the projector.
-
Page 57: Other Care
Troubleshooting Other care Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year. Caring for the lens If the lens is fl awed, soiled or fogged, it could cause deterioration of display quality. -
Page 58: Troubleshooting
Troubleshooting Troubleshooting Troubleshooting If an abnormal operation should occur, stop using the projector immediately. WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. -
Page 59: Regarding The Indicator Lamps
Troubleshooting Regarding the indicator lamps When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER LAMP TEMP Description indicator indicator indicator Lighting Turned Turned The projector is in a standby state. Orange Please refer to the section “Power on/off”. -
Page 60: Shutting The Projector Down
Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP Description indicator indicator indicator There is a possibility that the interior portion has become heated. Please turn the power off, and allow the projector to cool down at least Blinking 20 minutes. After the projector has suffi ciently cooled down, please make confi... -
Page 61: Phenomena That May Be Easy To Be Mistaken For Machine Defects
Troubleshooting Phenomena that may be easy to be mistaken for machine defects About the phenomenon confused with a machine defect, check and cope with it according to the following table. Reference Phenomenon Cases not involving a machine defect page The electrical power cord is not plugged in. Correctly connect the power cord. - Page 62 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The signal cables are not correctly connected. Correctly connect the audio cables. The MUTE function is working. Restore the sound pressing MUTE or VOLUME +/- button on the remote control.
- Page 63 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The brightness and/or contrast are adjusted to an extremely low level. Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function.
-
Page 64: Xit Specifi Cations
Specifi cations Specifi cations Specifi cations Specifi cation Item Specifi cation Product name Liquid crystal projector Liquid Crystal Panel 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens, f = 19 ~ 23 mm (approximately) Lamp 210W UHP Speaker Power supply AC 100-120V/3.7A, AC220-240V/1.8A Power consumption... - Page 65 Specifi cations Specifi cations (continued) [unit: mm]...