Makita DTD154 Instruction Manual
Hide thumbs
Also See for DTD154:
- Instruction manual (77 pages) ,
- Instruction manual (73 pages) ,
- Instruction manual (56 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DTD154
Summary of Contents for Makita DTD154
- Page 1 INSTRUCTION MANUAL Cordless Impact Driver DTD154 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DTD154 Fastening capacities Machine screw 4 mm - 8 mm Standard bolt 5 mm - 16 mm High tensile bolt 5 mm - 14 mm No load speed Hard impact mode 0 - 3,600 min Medium impact mode... -
Page 3: General Power Tool Safety Warnings
Prevent unintentional starting. Ensure the SAFETY WARNINGS switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with General power tool safety warnings your finger on the switch or energising power tools that have the switch on invites accidents. WARNING: Remove any adjusting key or wrench before Read all safety warnings and all... - Page 4 WARNING: DO NOT let comfort or familiarity causing fires, personal injury and damage. It will with product (gained from repeated use) replace also void the Makita warranty for the Makita tool and strict adherence to safety rules for the subject charger. product. MISUSE or failure to follow the safety rules stated...
-
Page 5: Functional Description
Indicating the remaining battery FUNCTIONAL capacity DESCRIPTION Only for battery cartridges with "B" at the end of the model number CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge CAUTION:... -
Page 6: Overheat Protection
Overheat protection Lighting up the front lamp When the tool/battery is overheated, the tool stops automatically. In this situation, let the battery cool CAUTION: Do not look in the light or see the before turning the tool on again. source of light directly. Overdischarge protection When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery. - Page 7 Reversing switch action CAUTION: Always check the direction of rotation before operation. CAUTION: Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may dam- age the tool. CAUTION: When not operating the tool, always set the reversing switch lever to the neu-...
- Page 8 Impact force grade displayed Maximum blows Purpose Example of application on panel Hard 3,800 min (/min) Tightening when force and Tightening underwork mate- speed are desired. rials, tightening long screws, tightening bolts. Medium 2,600 min (/min) Tightening when a good finish- Tightening finishing boards, ing is needed. plaster boards.
-
Page 9: Operation
Procedure 2 OPERATION In addition to Procedure 1, insert the bit-piece into the sleeve with its pointed end facing in. The proper fastening torque may differ depending upon ► 1 . Driver bit 2. Bit-piece 3. Sleeve the kind or size of the screw/bolt, the material of the workpiece to be fastened, etc. The relation between fas- To remove the driver bit, pull the sleeve in the direction tening torque and fastening time is shown in the figures. -
Page 10: Maintenance
These accessories or attachments NOTICE: If you use a spare battery to continue are recommended for use with your Makita tool the operation, rest the tool at least 15 min. specified in this manual. The use of any other accessories or attachments might present a risk of NOTE: Use the proper bit for the head of the screw/ injury to persons. Only use accessory or attachment... - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885506-223 www.makita.com 20160216...