Accessories - Amana ART104TFDB00 User Instructions

If you experience Possible Causes and/or Recommended Solutions
The door is blocked open - Move food packages away from door. Push bin or shelf back into the correct
The door will not
I
position. Make sure the crisper cover is fully pushed in, so that the back rests on the supports.
close completely
Gaskets are dirty or sticky - Clean gaskets and contact surfaces with mild soap and warm water. Rinse
The door is
I
and dry with soft cloth.
difficult to open
New Installation - Allow 24 hours following installation for the refrigerator to cool completely.
Temperature is
I
too warm
Door(s) opened often or not closed completely - Allows warm air to enter refrigerator. Minimize door
I
openings and keep doors fully closed.
A large amount of warm food has been recently added - Allow several hours for refrigerator to return to
I
normal temperature.
Check that the Temperature Control(s) are set correctly for the surrounding conditions - Adjust the
I
controls to one setting colder. Check temperature in 24 hours. See "Using the Control(s)."
Humid room - Contributes to moisture buildup in the refrigerator.
There is interior
I
moisture buildup
Door(s) opened often or not closed completely - Allows humid air to enter the refrigerator. Minimize door
I
NOTE: Some
openings and keep door fully closed.
moisture buildup is
normal.
The ice maker is not connected to a water supply - Connect refrigerator to water supply and turn water
The ice maker is
I
shutoff valve fully open.
not producing ice
or not enough ice
A kink in the line can reduce water flow - Straighten the water source line.
I
(on some models)
Ice maker is not turned on - Make sure the ice maker wire shutoff arm or switch (depending on model) is
I
in the ON position.
New installation - Wait 24 hours after ice maker installation for ice production to begin. Wait 3 days for full
I
ice production.
Large amount of ice recently removed - Allow sufficient time for ice maker to produce more ice.
I
Ice cube jammed in the ice maker ejector arm - Remove ice from the ejector arm with a plastic utensil.
I
A reverse osmosis water filtration system connected to your cold water supply can decrease water
I
pressure - See "Water Supply Requirements."
The water valve is not completely open - Turn the water shutoff valve fully open.
The ice cubes are
I
hollow or small
A kink in the line can reduce water flow - Straighten the water source line.
I
(on some models)
A reverse osmosis water filtration system connected to your cold water supply can decrease water
NOTE: This is an
I
pressure - See "Water Supply Requirements."
indication of low
water pressure.
If questions regarding water pressure remain, call a licensed, qualified plumber.
I
New plumbing connections can cause discolored or off-flavored ice - Discard the ice and wash the ice
Off-taste, odor or
I
storage bin. Allow 24 hours for the ice maker to make new ice, and discard the first 3 batches of ice
gray color in the
produced.
ice (on some
models)
Ice stored too long can develop an off-taste - Discard ice. Wash ice bin. Allow 24 hours for ice maker to
I
make new ice.
Food odor transferring to ice - Use airtight, moisture proof packaging to store food.
I
There are minerals (such as sulfur) in the water - A water filter may need to be installed to remove the
I
minerals.
The following accessories are available for your refrigerator. To
order, contact us and ask for the Part Number.
In the U.S.A., visit our web page www.amana.com or call
1-800-442-9991.
In Canada, visit our web page www.amanacanada.ca
or call 1-800-807-6777.

ACCESSORIES

affresh ® Stainless Steel Cleaner:
In U.S.A., order Part #W10355016
In Canada, order Part #W10355016B
affresh ® Stainless Steel Wipes:
In U.S.A., order Part #W10355049
In Canada, order Part #W10355049B
affresh ® Kitchen & Appliance Cleaner:
In U.S.A., order Part #W10355010
In Canada, order Part #W10355010B
15