Panasonic PP105168 Operating Instructions Manual page 3

Weather band receiver
Table of Contents

Advertisement

Caution
Observe the following cautions when
using this unit.
Keep the sound volume at an appropriate
level.
Keep the volume level low enough to be aware of
road and traffic conditions while driving.
This unit is designed for use exclusively in
trucks.
Do not operate the unit for a prolonged period
with the engine turned off.
Operating the audio system for a long period of
time with the engine turned off will drain the bat-
tery.
Do not expose the unit to direct sunlight or
excessive heat.
Otherwise these will raise the interior temperature
of the unit, and it may lead to smoke, fire, or other
damage to the unit.
Do not use the product where it will be ex-
posed to water, moisture, or dust.
Exposure of the unit to water, moisture, or dust
may lead to smoke, fire, or other damage to the
unit. Make especially sure that the unit does not get
wet in truck washes or on rainy days.
To ensure safety, never attempt to preset sta-
tions while you are driving.
Depending upon the transmission condition
of electro-magnetic waves, the geographical
reasons and/or the weather conditions, you may
not receive the NOAA radio partially or at all.
Make sure that your weather radio can receive
properly before driving, especially, before use
in a critical condition.
Set the volume level to low enough before the
AUX connection is completed.
Failure to observe this, the loud noise may come
out and damage your speakers and your hearing.
Direct connection of the speaker/headphone output
of an external device without any attenuator may
distort sound or damage the connected external
device.
When using this unit, noise may occurs when
there is an electromagnetic-wave generator
such as a cellular phone near this unit, if that
noise is obvious and cannot be eliminated,
please keep an electromagnetic-wave genera-
tor such as a cellular phone away from this
unit.
Observe the following cautions when
installing.
Refer wiring and installation to qualified
service personnel.
Installation of this unit requires special skills and
experience. For maximum safety, have it installed by
the dealership. We are not liable for any problems
resulting from your own installation of the unit.
Follow the instruction to install and wire the
product.
Not following the instructions to properly install and
wire the product could cause an accident or fire.
Take care not to damage the leads.
When wiring, take care not to damage the leads.
Prevent them from getting caught in the vehicle
chassis, screws, and moving parts such as seat
rails. Do not scratch, pull, bend or twist the leads.
Do not run them near heat sources or place heavy
objects on them. If leads must be run over sharp
metal edges, protect the leads by winding them
with vinyl tape or similar protection.
Use the designated parts and tools for installa-
tion.
Use the supplied or designated parts and appropri-
ate tools to install the product. The use of parts
other than those supplied or designated may result
in internal damage to the unit. Faulty installation
may lead to an accident, a malfunction or fire.
Do not block the air vent or the cooling plate of
the unit.
Blocking these parts will cause the interior of the
unit to overheat and will result in fire or other dam-
age.
Do not install the product where it is exposed
to strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for
installation. If the installation is not stable, the unit
may fall down while driving and this can lead to an
accident or injury.
Installation Angle
The product should be installed in a horizontal posi-
tion with the front end up at a convenient angle.
The user should bear in mind that in some areas
there may be restrictions on how and where this
unit must be installed. Consult your dealer for
further details.
Wear gloves for safety. Make sure that wiring
is completed before installation.
To prevent damage to the unit, do not connect
the power connector until the whole wiring is
completed.
Do not connect more than one speaker to one
set of speaker leads. (except for connecting to
a tweeter)
3

Advertisement

Table of Contents
loading

This manual is also suitable for:

932cr-bt4509

Table of Contents