Related Manuals for LG 23CAT42K-B.AUS
Summary of Contents for LG 23CAT42K-B.AUS
- Page 1 OWNER'S MANUAL CLOUD MONITOR (LED LCD MONITOR) Please read the safety information carefully before using the product. CLOUD Monitor(LED LCD Monitor) Model 23CAT42K www.lg.com...
-
Page 2: Table Of Contents
Table of Contents TABLE OF CONTENTS ASSEMBLING AND PRODUCT SPECIFICATION PREPARING Preset Mode Unpacking Power Indicator Parts and buttons Lifting and moving the Monitor PROPER POSTURE Setting Up the Monitor set Proper posture for using the monitor - Attaching the Stand Base - Mounting on a table USING THE CITRIX CLOUD - Adjusting the angle... -
Page 3: Assembling And Preparing
Stand Base (This cable is not included in all counties) CAUTION Only use an approved LG power adapter. Damage caused by other power adapters is not covered by warranty. NOTE Note that the components may look different from those shown here. -
Page 4: Parts And Buttons
ASSEMBLING AND PREPARING Parts and buttons Input Connectors (See p.15 ) Power Indicator LED On : Power is on LED Off: Power is off (Power Button) Front Side Buttons Input Connectors (See p.12 to 15) -
Page 5: Lifting And Moving The Monitor
ASSEMBLING AND PREPARING Lifting and moving the Setting Up the Monitor set Monitor Attaching the Stand Base Please heed the following information when moving the monitor. Place the monitor's screen face down. CAUTION CAUTION To protect the screen from scratches, cover Avoid touching the screen at all times, as this the surface with a soft cloth. -
Page 6: Mounting On A Table
ASSEMBLING AND PREPARING Mounting on a table Adjusting the angle Lift the monitor and place it on the table in an Place the monitor mounted on the stand base upright position. in an upright position. Install at least 10 cm away from the wall to ensure sufficient ventilation. -
Page 7: Adjusting The Stand Height
ASSEMBLING AND PREPARING Adjusting the stand height Using the Kensington locking device Place the monitor mounted on the stand base The connector for the Kensington lock is located in an upright position. on the rear of the monitor. For more information on installation and usage, Remove the tape attached at the bottom rear refer to the Kensington lock user manual or visit of the stand body, then pull out the locking... -
Page 8: Detaching The Stand Base
ASSEMBLING AND PREPARING Detaching the stand base Detaching the stand body Place the monitor's screen face down. Place the monitor's screen face down. To protect the screen from scratches, cover the To protect the screen from scratches, cover the surface with a soft cloth. surface with a soft cloth. -
Page 9: Swivel Stand
ASSEMBLING AND PREPARING Swivel stand Be careful with the cables when rotating the screen. Image shown may differ from your Monitor set. Swivel 90 degrees and adjust the angle of the Monitor set to suit your view. Using the Pivot function The pivot function allows you to rotate the screen 90 degrees clockwise. -
Page 10: Installing The Wall Mount Plate
Mounting on a wall This monitor has a VESA compatible mount on the Install the monitor at least 10 cm away from the back. Most mounts will require an LG mounting wall and leave about 10 cm of space at each side plate. - Page 11 Installing the monitor on the ceiling or on a slanted wall may result in the monitor falling off, which could lead to injury. Please use a LG wall mounting bracket when using a VESA mount. For more information, contact your local retail store or a qualified installer.
-
Page 12: Using The Monitor Set
USING THE MONITOR SET USING THE MONITOR SET Connecting Input Signal Cable NOTE This monitor supports the *Plug and Play Apple Adapter feature. An adapter may be needed for Apple *Plug and Play: A feature that allows you to add a device to your computer, without having computers. -
Page 13: Dvi Connection
USING THE MONITOR SET DVI connection CAUTION Transfers digital video signals from the Cloud Mon- Connect the input signal itor to an extended monitor. cable and tighten in the Connect the Cloud Monitor to an extended monitor direction of the arrow. To using a DVI cable. -
Page 14: Connecting Lan/Peripherals
USING THE MONITOR SET Connecting LAN/Peripherals NOTE LAN connection The LAN cable is sold separately. The following LAN cable type can be used: Connect the router or switch to the monitor using a Standard: IEEE 802.3 ETHERNET LAN cable as illustrated below. If a device is connected into the earphone out port via a LAN cable, you can adjust the volume with the volume icon on PC taskbar. -
Page 15: Peripheral Device Connection
USING THE MONITOR SET Peripheral device connection NOTE Connect peripheral devices to the monitor using Peripheral devices are sold separately. USB, microphone and headphone ports. The USB ports on the left and bottom of the monitor can be used to connect the key- board, mouse, and other USB devices. -
Page 16: Self Image Adjustment
USING THE MONITOR SET Self Image Adjustment Press the power button on the front to turn on the monitor. When powered on, the "Self Image Adjustment" function will run automatically (only available for analog [D-SUB input] signals). NOTE What is "Self Image Adjustment"? This func- tion runs when the monitor is connected for the first time and performs automatic image adjustment for each signal (only available for... -
Page 17: Customizing Settings
CUSTOMIZING SETTINGS CUSTOMIZING SETTINGS Press the desired button on the bottom of the Monitor set. Change the value of the menu item by pressing the buttons on the bottom of the Monitor set. To return to the upper menu or set other menu items, use the up arrow ( ) button. -
Page 18: Customizing Settings
CUSTOMIZING SETTINGS Customizing Settings Menu Settings Press MENU button on the bottom of the Monitor set to display the MENU OSD. Set the options by pressing the ◄ or ► or ▼ buttons. Select the "NEXT MENU" button to enter the more option settings. -
Page 19: Picture
CUSTOMIZING SETTINGS PICTURE Press MENU button on the bottom of the Monitor set to display the MENU OSD. Select the "NEXT MENU" button to enter the more option settings. Enter to PICTURE by pressing the ▼ button. Set the options by pressing the ◄ or ► buttons. Select EXIT to leave the OSD menu. -
Page 20: Color
CUSTOMIZING SETTINGS COLOR Press MENU button on the bottom of the Monitor set to display the MENU OSD. Select the "NEXT MENU" button to enter the more option settings. Select COLOR by pressing the ► button. Enter to COLOR by pressing the ▼ button. Set the options by pressing the ◄... -
Page 21: Display
CUSTOMIZING SETTINGS DISPLAY Press MENU button on the bottom of the Monitor set to display the MENU OSD. Select the "NEXT MENU" button to enter the more option settings. Select DISPLAY by pressing the ► button. Enter to DISPLAY by pressing the ▼ button. Set the options by pressing the ◄... -
Page 22: Others
CUSTOMIZING SETTINGS OTHERS Press MENU button on the bottom of the Monitor set to display the MENU OSD. Select the "NEXT MENU" button to enter the more option settings. Select OTHERS by pressing the ► button. Enter to OTHERS by pressing the ▼ button. Set the options by pressing the ◄... -
Page 23: Volume
CUSTOMIZING SETTINGS VOLUME Press the VOL button at the bottom of the monitor to display the VOL OSD menu. Press the ◄ or ► button to adjust the volume. Press the button to enable or disable Mute. Select EXIT to leave the OSD menu. Each option is explained below. -
Page 24: Troubleshooting
Troubleshooting TROUBLESHOOTING Nothing is displayed on the screen Is the monitor's power cord plugged in? y Check if the power cord is correctly plugged in to the outlet. Is the power indicator on? y Check the power indicator. y Adjust the brightness and the contrast. Is the power indicator displaying as red? y If the monitor is in power saving mode, move the mouse or press any... - Page 25 Troubleshooting The image is displayed abnormally. Does the display area appear un- Pressing the AUTO button will automatically optimize the screen to the current centered? display mode. Does the screen exhibit vertical Pressing the AUTO button will automatically optimize the screen to the current lines? display mode.
-
Page 26: Product Specification
Product Specification PRODUCT SPECIFICATION 23CAT42K LCD Screen Type 58.42 cm (23 inch) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Screen Diagonal length of the screen: 58.42 cm Pixel Pitch 0.2652 mm x 0.2652 mm Resolution Maximum Resolution 1920 x 1080 @ 60 Hz Recommended Resolution 1920 x 1080 @ 60 Hz DVI-D output 1920 x 1200 @ 60 Hz... -
Page 27: Preset Mode
Product Specification Preset Mode 23CAT42K Display Modes Horizontal Vertical Polarity (H/V) Remark (Resolution) Frequency (kHz) Frequency (Hz) 720 x 400 31.468 70.08 640 x 480 31.469 59.94 800 x 600 37.879 60.317 1024 x 768 48.363 1280 x 1024 63.981 60.02 1680 x 1050 65.290... -
Page 28: Proper Posture
Proper Posture PROPER POSTURE Proper posture for using the monitor Adjust the angle so that the screen is slightly lower than your eyes. Using the monitor for a prolonged period of time can cause eye fatigue. Take a 10-minute break every hour. -
Page 29: Using The Citrix Cloud Monitor
[Log in Window] Enter user name, password and domain to con- nect to the VDI server. After power on, restart or factory reset, the LG logo is displayed as shown below. y Network status: If a network connection is available, the message "Connected" next to the round green icon is displayed. - Page 30 Diagnosis" function enables the system program for managingthen cloud products to check and diagnose problems with the provided by LG Electronics. network connection, network setting or VDI server. The time required to connect to the VDI server may vary depending on the network environment.
-
Page 31: Application Screen
USING CITRIX CLOUD MONITOR Application Screen [3] Adding applications y A list of applications that can be added is dis- If there is only one virtual OS for the user account, played. the system is connected to the OS directly. y When you select an item, focus is given to the item and the sub-list is displayed. -
Page 32: Power Button
USING CITRIX CLOUD MONITOR Setting Button Power Button With this button, you can set the network, server On the Log in screen, if you click MENU > Power, and language for the Cloud monitor. you can select "Power Off" or "Restart". [Power Off] [Language Setting] Select the "Power Off"... - Page 33 You can select Auto-Detect, 10Mbps, software program for managing the cloud products 100Mbps or 1000Mbps. provided by LG Electronics. y DHCP: sets the DHCP mode. When DHCP is set to On, the IP address from the DHCP server is populated.
- Page 34 USING CITRIX CLOUD MONITOR eZ-CMS Setting Primary Display Setting y Enter the eZ-CMS server address to connect to y Resolution: sets the resolution of the monitor. the management software. 23CAT42K: the Cloud monitor supports the fol- lowing resolution: Auto, 1920x1080, 1680x1050, 1280x1024 and 1024x768.
- Page 35 USING CITRIX CLOUD MONITOR Secondary Display Setting [Volume Setting] y Resolution: sets the resolution of the monitor. You can set the volume for Playback and MIC. Se- The following options are available for the reso- lect the “Mute” checkbox to mute the playback and lution supported by the DVI monitor.
- Page 36 USING CITRIX CLOUD MONITOR [Mouse Setting] [Factory Reset] This menu resets the system to the factory default You can set the cursor speed by dragging the settings and reboots it. scroll bar. Select from "Right Handed" and "Left Handed" under the "Button Type" menu to change Click the "Reset"...
-
Page 37: Info Button
Wake on LAN can only be set in eZ-CMS. network connection. eZ-CMS is a software program for managing If the VDI address is not set, the address is the cloud products provided by LG Electronics. empty and the eZ-CMS server address is displayed as 0.0.0.0. -
Page 38: Pop-Up Message Linked To Ez-Cms
USING CITRIX CLOUD MONITOR Pop-up Message Linked to [Ping Tab] eZ-CMS On the Ping tab, you check the network connection to a specific IP address or host from a local client [1] Shutdown/Restart message as well as local network status. This pop-up window is used for performing shut- down or restart without delay or postponing shut- NOTE... - Page 39 USING CITRIX CLOUD MONITOR [2] Remote View [4] Firmware update notice This pop-up window is displayed when the eZ- The pop-up window is displayed when the eZ-CMS CMS manager asks for the remote view. manager sends the system firmware update com- y Selecting the "Yes"...
- Page 40 Address : 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U.S.A LG Electronics will also provide open source code to you on CD-ROM for a charge covering TEL: 201-266-2534 the cost of performing such distribution (such...