LG 47G2 Owner's Manual page 7

Warning - To reduce the risk of fire or
y y
electrical shock, do not expose this product
to rain, moisture or other liquids. Do not
touch the TV with wet hands. Do not install
this product near flammable objects such
as gasoline or candles, or expose the TV to
direct air conditioning.
Do not expose to dripping or splashing and
y y
do not place objects filled with liquids, such
as vases, cups, etc. on or over the apparatus
(e.g. on shelves above the unit).
Grounding
y y
(Except for devices which are not grounded.)
Ensure that you connect the earth ground
wire to prevent possible electric shock
(i.e. a TV with a three-prong grounded AC
plug must be connected to a three-prong
Short-circuit Breaker
grounded AC outlet). If grounding methods
are not possible, have a qualified electrician
install a separate circuit breaker. Do not try to
ground the unit by connecting it to telephone
wires, lightening rods, or gas pipes.
Short-circuit Breaker
DISCONNECTING DEVICE FROM MAINS
y y
Mains plug is the disconnecting device. The
plug must remain readily operable.
As long as this unit is connected to the AC
y y
wall outlet, it is not disconnected from the
AC power source even if the unit is turned
off.
Do not attempt to modify this product in any
y y
way without written authorization from LG
Electronics. Unauthorized modification could
void the user's authority to operate this
product.
Power Supply
Power Supply
Short-circuit Breaker
Power Supply
ANTENNAS Outdoor antenna grounding
y y
(Can differ by country):
If an outdoor antenna is installed, follow
the precautions below. An outdoor antenna
system should not be located in the vicinity
Antenna Lead in Wire
of overhead power lines or other electric light
Antenna Lead in Wire
or power circuits, or where it can come in
Antenna Discharge Unit
(NEC Section 810-20)
Antenna Discharge Unit
contact with such power lines or circuits as
Grounding Conductor (NEC Section 810-20)
(NEC Section 810-21)
Grounding Conductor
Ground Clamps (NEC Section 810-21)
death or serious injury can occur. Be sure the
Power Service Grounding Ground Clamps
Electrode System
antenna system is grounded so as to provide
(NEC Art 250, Part H) Power Service Grounding
NEC: National Electrical Code Electrode System
(NEC Art 250, Part H)
some protection against voltage surges
NEC: National Electrical Code
and built-up static charges. Section 810 of
the National Electrical Code (NEC) in the
U.S.A. provides information with respect to
Antenna Lead in Wire
proper grounding of the mast and supporting
Antenna Discharge Unit
(NEC Section 810-20)
structure, grounding of the lead-in wire to
Grounding Conductor
(NEC Section 810-21)
an antenna discharge unit, size of grounding
Ground Clamps
conductors, location of antenna discharge Power Service Grounding
Electrode System
(NEC Art 250, Part H)
NEC: National Electrical Code
unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Ground Clamp
Electric Service
Equipment
Ground Clamp
NEC: National Electrical Code
y Cleaning
y
NEC: National Electrical Code
When cleaning, unplug the power cord and
wipe gently with a soft cloth to prevent
scratching. Do not spray water or other
liquids directly on the TV as electric shock
may occur. Do not clean with chemicals
such as alcohol, thinners or benzine.
Moving
y y
Make sure the product is turned off,
unplugged and all cables have been
removed. It may take 2 or more people to
carry larger TVs. Do not press or put stress
on the front panel of the TV.
Ventilation
y y
Install your TV where there is proper
ventilation. Do not install in a confined
space such as a bookcase. Do not cover the
product with cloth or other materials while
plugged. Do not install in excessively dusty
places.
7
Before Use
Antenna Lead
Antenna Disc
Antenna Lead in Wire
(NEC Section
Grounding Co
Antenna Discharge Unit
(NEC Section 810-20) (NEC Section
Grounding Conductor
(NEC Section 810-21)
Ground Clamp
Power Service Grounding
Electrode System
Power Service
(NEC Art 250, Part H)
Electrode Sys
(NEC Art 250,