Advertisement
English
Supplied accessories
– AC power cord
Top and front panels (See 1)
1 Source selector:
CD,TUNER (MW/FM),
TAPE/OFF
– selects CD, tuner (MW or FM) or tape
source of sound
– switch off switch
2 VOLUME – adjusts volume level
3 LIFT•OPEN – opens the CD door
4 MIC (built-in microphone) – for voice
recording via cassette recording
5 Cassette recorder keys:
; – pauses playback or recording
9/ – stops the tape;
– opens the cassette holder
5 or 6 – fast winds/ rewinds tape
1 – starts playback
0 – starts recording
6 CD Display – shows the CD functions
7 PROG – programs and reviews
programmed track numbers
8 REPEAT – repeats a track/
CD program/entire CD
9 BAND – selects FM or MW waveband
0 TUNING – tunes to radio stations
! 2; – starts or pauses CD playback.
9 – stop playback;
– erases a CD program
∞, § – skips or searches a passage/track
backwards
4
Controls/Power Supply
Back panel (See 1)
@ Telescopic antenna – improves FM
reception
# Battery door – open to insert 6 x 1.5V
R-14/ UM2/ C-cells
$ p – 3.5 mm stereo headphone socket
Helpful hints: The speakers will be muted
when headphones are connected to the set.
% AC MAINS – inlet for power cord
CAUTION
- Visible and invisible laser radiation.
If the cover is open, do not look at
the beam.
- High voltage! Do not open.You run
the risk of getting an electric shock.
The machine does not contain any
user-serviceable parts.
- Modification of the product could
result in hazardous radiation of
EMC or other unsafe operation.
Power Supply
Whenever convenient, use the mains supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1 Open the battery compartment and insert
six batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct polarity
as indicated by the "+" and "–" symbols inside
the compartment. (See 1)
2 Replace the compartment door, making sure
the batteries are firmly and correctly in place.
The set is now ready to operate.
Batteries contain chemical substances, so
they should be disposed of properly.
•
Incorrect use of batteries can cause
electrolyte leakage and will corrode the com-
partment or cause the batteries to burst:
Power Supply
•
Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.
•
When inserting new batteries, do not try to
mix old batteries with the new ones.
•
Remove the batteries if the set is not to be
used for a long time.
Using AC Mains
1 Check if the power/mains voltage, as shown
on the type plate located on the
bottom of the set, corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2 Connect the power cord to the AC MAINS
inlet and the wall socket.The mains lead is
now connected and ready for use.
3 To switch the set off completely, withdraw the
power cord from the wall socket.
4
Install the unit near the AC outlet and where
the AC power plug can be easily reached.
•
Disconnect the mains lead from the wall
socket to protect your set during heavy
thunderstorms. Children could seriously injure
themselves as the free end of the cable may
still be live if only the connector is removed
from the MAINS socket at the back of the
unit.
The type plate is located on the bottom
of the set.
Helpful hints :
–
To avoid unnecessary energy consumption,
always adjust the source selector to
TAPE/OFF after using the set, and also
check that the tape deck keys are released.
General Operation/Radio
General operation
1 To select your sound source, adjust the
source selector to : CD, TUNER or
TAPE/OFF.
2 To switch off the set, adjust the source
selector to TAPE/OFF position and check
the cassette keys are released.
Helpful hints:
–
To change from TAPE to TUNER or CD
function, or when you are switching off the set:
first, make sure you press the tape 9/ key to
end playback and all the cassette keys are
released.
Adjusting volume
Adjust the volume with the VOLUME
control.
Radio reception
1 Adjust the source selector to TUNER.
2 Adjust BAND to FM or MW as your
desired band.
3 Turn TUNING to tune to a station.
•
For FM, extend and turn the telescopic
antenna for best reception. Reduce its length
if the signal is too strong.
•
For MW, the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.
4 To switch off the radio, adjust the source
selector to TAPE/OFF position and check
the cassette keys are released.
5
Advertisement
