Samsung SyncMaster 730MP Manual page 52

Picture rolls vertically.
"Check Signal Cable" message
Image is not clear. Picture is
blurred.
"Not Supported Mode" message
Picture image is unstable and
vibrates.
Picture rolls vertically.
Ghost images are shown in the
picture.
The image is too light or too dark
Image is not clear. Picture is
blurred.
Screen color is inconsistent.
Color image is distorted with
Picture image is unstable and
dark shadows.
vibrates.
White color is poor.
Ghost images are shown in the
picture.
Power Indicator blinks green.
The image is too light or too dark
Screen is blank and power
indicator light is steady green or
Screen color is inconsistent.
blinks every 0.5 or 1 seconds
Color image is distorted with
The screen is blank and is
dark shadows.
blinking.
White color is poor.
Power Indicator blinks green.
3. Problems related to Audio
Problems related to audio signals and their solutions are listed below.
Screen is blank and power
indicator light is steady green or
blinks every 0.5 or 1 seconds
Problems
The screen is blank and is
blinking.
No sound
3. Problems related to Audio
Problems related to audio signals and their solutions are listed below.
Sound level is too low.
Problems
No sound
Sound is too high pitched or too
low pitched
4. Problems related to Remote Control
Problems related to the remote control and their solutions are listed.
Sound level is too low.
Problems
The remote control buttons do
Sound is too high pitched or too
not respond.
low pitched
(Refer to the Connecting the
Check if the signal cable is securely connected.
Connect it again securely.
(Refer to Connecting to a
Ensure that the signal cable is firmly connected to the PC or
video sources.
(Refer to the Connecting the
Run Frequency Coarse and
Ensure that the PC or video sources are turned on.
Turn on again after removing all accessories
(video extension cable, etc.)
Set resolution and frequency to the recommended ranges.
Check the maximum resolution and the frequency of the
video adaptor.
Compare these values with the data in the
Check if the resolution and frequency set for the computer
Modes Chart.
video card falls in the range supported by the monitor.
If not, reset them referring to the current
the monitor menu and Preset Timing
Check if the signal cable is securely connected.
Connect it again securely.
(Refer to Connecting to a
Adjust the Brightness and Contrast.
Run Frequency Coarse and
(Refer to the Brightness, Contrast)
Turn on again after removing all accessories
(video extension cable, etc.)
Adjust color using Custom
Set resolution and frequency to the recommended ranges.
menu.
Check if the resolution and frequency set for the computer
video card falls in the range supported by the monitor.
If not, reset them referring to the current
the monitor menu and Preset Timing
The monitor is currently saving the changes made in settings
to the OSD memory.
Adjust the Brightness and Contrast.
(Refer to the Brightness, Contrast)
The monitor is using its power management system.
Press a key on the keyboard
Adjust color using Custom
menu.
If you see the "TEST GOOD" message on the screen when
you press the MENU button, check the cable connection
between the monitor and the computer to ensure that the
connector is properly connected.
The monitor is currently saving the changes made in settings
to the OSD memory.
The monitor is using its power management system.
Press a key on the keyboard
Solutions
If you see the "TEST GOOD" message on the screen when
you press the MENU button, check the cable connection
Ensure that the audio cable is firmly connected to both the
between the monitor and the computer to ensure that the
audio-in port on your monitor and the audio-out port on your
connector is properly connected.
sound card.
(Refer to the Connecting the
Check the volume level.
(Refer to the Volume)
Check the volume level.
(Refer to the Volume)
If the volume is still too low after turning the control to its
maximum, check the volume control on the computer sound
Solutions
card or software program.
Ensure that the audio cable is firmly connected to both the
Adjust the Treble and Bass
audio-in port on your monitor and the audio-out port on your
sound card.
(Refer to the Connecting the
Check the volume level.
(Refer to the Volume)
Check the volume level.
(Refer to the Volume)
If the volume is still too low after turning the control to its
maximum, check the volume control on the computer sound
Items to check
card or software program.
Check the battery polarities (+/-).
Adjust the Treble and Bass
Check if the batteries have been exhausted.
Monitor)
Computer)
Monitor)
Fine tuning.
Preset Timing
Information
Modes.
Computer)
Fine tuning.
under OSD Color Adjustment
Information
Modes.
under OSD Color Adjustment
Monitor)
to appropriate level.
Monitor)
to appropriate level.
under
under