Table Of Contents - Yamaha PDP-300 Owner's Manual

CONTENTS
KEYBOARD STAND ASSEMBLY ......................... 2
THE CONTROLS AND CONNECTORS ................. 4
LISTEN TO THE DEMONSTRATION.................... 6
PLAYING THE PDP-300 ...................................... 6
DUAL MODE ........................................................ 7
TOUCH SENSITIVITY .......................................... 7
TAKING CARE OF YOUR PDP-300
Your PDP-300 is a fine musical instrument, and de-
serves the most careful treatment. Observe the following
points and your PDP-300 will sound and look great for
many years.
1. Never open the case and touch or tamper with the in-
ternal circuitry.
2. Always turn the POWER switch OFF after use, and
cover the instrument with the dust cover provided.
3. Clean the cabinet and keys of your PDP-300 only with
a clean, slightly damp cloth. A neutral cleanser may
be used if desired. Never use abrasive cleansers,
waxes, solvents or chemical dust cloths since these
can dull or damage the finish.
4. Never place any vinyl products on your PDP-300.
Contact with vinyl can cause irreversible damage to
the finish.
5. Install your PDP-300 in a place that is away from di-
rect sunlight, excessive humidity or heat.
6. Never apply excessive force to the controls, connec-
tors or other parts of your PDP-300, and avoid
scratching or bumping it with hard objects.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT
: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
3. NOTE:
This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for
Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of
this product in a residential environment will not result in harmful interference with other electronic devices. This equip-
ment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users
manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations
does not guarantee that interference will not occur in all installations. If this product is found to be the source of interfer-
ence, which can be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by using one of
the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Elec-
tronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
FCC INFORMATION (U.S.A.)
TRANSPOSITION ................................................. 7
PITCH CONTROL ................................................. 7
MIDI FUNCTIONS ................................................ 8
MIDI DATA FORMAT ......................................... 11
TROUBLESHOOTING ......................................... 13
SPECIFICATIONS............................................... 13
PREPARATION
• Check your power supply
Make sure that your local AC mains voltage matches
the voltage specified on the name plate on the bottom
panel. Make sure that the voltage selector is set for the
voltage in your area.
• The music stand
If you will be using sheet music with your PDP-300,
raise the music stand built into it's top panel by lifting
the rear edge of the music stand until it clicks into
place.
The music stand can be lowered after slightly lifting
the stand and pressing the two brackets which support it
inward.
1