Prior To Installation; Control Descriptions - Cerwin-Vega CVT-12 Operating Instructions Manual

S u b w o o f e r
P
RIOR TO INSTALLATION
Carefully unpack your subwoofer, saving the box and all of the packing material; at
some point you may need to transport, ship, or move your subwoofer. Before
continuing with the installation, please make sure the subwoofer is unplugged and
WARNING: Severe damage may result from
the power switch is turned "OFF. "
improperly selected voltage. Set voltage selection switch,
I
NSTALLATION
Please read the following to determine which installation procedure is best for your
audio/video system. For additional hook-up connections, you may want to refer to
your A/V receiver, processor, preamplifier, or amplifier's manual.
and observe the "Safety Instructions" on preceding page before starting the installation.
C D
ONTROL ESCRIPTIONS
The following controls are located on the subwoofer's rear panel, as shown (back cover).
Attention! The Cerwin-Vega VE-28S have LFE, LINE-LEVEL, and SPEAKER-
LEVEL input connections; choose one option only for hook-up. Do not hook up
more than one option!
LFE INPUT: Mono "low frequency effects"connection. Use this input if
receiver/preamp/processor has a dedicated LFE or subwoofer OUT. Refer to
the owner's manual provided by your receiver/preamp/processor manufacturer.
(see figure 1, back cover for hook-up)
LINE-LEVEL INPUT: Stereo low level input to subwoofer. Connect to "LINE-OUT",
"MAIN-OUT or PREAMP-OUT", of your receiver/preamp/processor using a dual RCA
patchcord (not supplied). Refer to the owner's manual provided by your receiver/
preamp/processor manufacturer. (see figure 2, back cover for hook-up)
SPEAKER-LEVEL INPUT: Stereo high-level inputs to subwoofer. Use these terminals
when line-level connections are not available from A/V receiver/preamp/processor.
Connect to SPEAKER outputs on receiver using high quality speaker wire (16-gauge
or heavier). (see figure 3, back cover for hook-up)
SPEAKER-LEVEL OUTPUT: Audio loop of stereo high-level (SPEAKER-LEVEL)
inputs . Use to loop (continue) signal to speaker connections to the left
and right main speakers.
VOLUME CONTROL: Controls volume level of subwoofer. Use to balance the output
of the subwoofer with the main speaker output.
CROSSOVER FREQUENCY: The crossover control allows you to adjust the upper
limit of the subwoofer's frequency response from 40 to 120 Hz. The subwoofer's
response will begin rolling off above the set frequency. Set the CROSSOVER FRE-
QUENCY to the lower value listed in the main speaker manual.* (Note: Crossover
control does not function when LFE input is used.)
PHASE: This switch allows you to compensate for having the subwoofer
in a different location than the main speakers. This control allows the signal to be
delayed 180 degrees so the output of the subwoofer will blend in with the
main speakers. Slide the PHASE switch to "180". At the listening position, listen to
the midbass output. If it sounds weak, set PHASE back to "0."
POWER LED: Power indicator lamp. Glows green in "ON"mode if audio signal is
present. Glows red in both "OFF"mode and "ON "mode if receiving AC power,
and if audio signal is not present after approximately 30 minutes.
T
ROUBLESHOOTING
S C
YMPTOM AUSE
Bass sounds distorted Subwoofer amplifier has
reached maximum output
Tone controls are set too
high
Distortion with volume control Defective receiver or
near minimum preamplifier; shorted
speaker wires
Distortion on music peaks or Dynamic soundtrack (e.g.,
sound effects explosions)
Buzz, hum, or crackle when Connecting wires with
connecting wires power on causes transient
signal spikes
Buzz or hum when system is Grounding problem or
on ground loop
No sound after listening at Amplifier's thermal
high levels protection is on
to the proper AC voltage.
NOTE: Be sure to read
S
OLUTION
Turn down volume control
on subwoofer or lower
receiver level
Set bass flat; use controls
sparingly
Repair defective receiver,
preamplifier or replace
speaker wires
Turn down volume control to
lower overall range; use a
more powerful
receiver/amplifier
Connect wires only when
audio system power is off
Check receiver or
preamplifier manual for
ground loop elimination
Turn down volume control
and allow amplifier to cool;
sound should resume
automatically
USA: Cerwin-Vega, 9340 De Soto Ave., Chatsworth, CA 91311
Stanton Group Europe: 382 Avenue de la Couronne, 1050 Brussels, Belguim
I n s t a l l a t i o n
POWER: Two-position power switch. In the "ON"mode, the subwoofer's
amplifier is automatically activated if an audio signal is present and will automatically
become inactive when there is no audio signal present after approximately 30
minutes. In the "OFF" mode, power is shut off to the amplifier.
VOLTAGE SELECTION: User-switchable voltage selection for use with 110-120V/
Attention: All subwoofer models come from the factory preset to
220-240V AC.
110-120 volts.
To select a different voltage, use a flat head screwdriver to reposition
the switch to the desired voltage.
improperly selected voltage. Make sure you know the voltage requirement of
the country you are in before attempting to connect this subwoofer to AC
power.
POWER CORD RECEPTACLE: Connect IEC cord to this receptacle (supplied
with the VE subwoofer). If the cord supplied does not fit an available AC outlet,
purchase the correct AC cord from your audio dealer or an electrical supply store.
REPLACEABLE FUSE: Protects system from overload, replace with fuse rating as
indicated on amplifier panel at fuse location. The fuse holder is located at the AC
receptacle. Gently pry open to access the fuse.
P
LACEMENT
Your VE Series powered subwoofer produces low frequencies which are omnidirectional.
As a result, placement requirements for your subwoofer are flexible and subject to your
listening room's acoustic characteristics. To determine the best position for your
subwoofer, start by positioning it along the same wall, or plane, as your main speakers.
Experiment with various locations until you find the location that sounds best to you.
Note: Typically, your powered subwoofer will sound louder when placed in close
proximity to walls or corners.
Caution! Cerwin-Vega VE-28S speakers are intended for FLOOR
PLACEMENT ONLY! Do not place heavy objects of any type, such as televisions on
top of any Cerwin-Vega speaker unless otherwise recommended by Cerwin-Vega!
VE Series speakers are for residential applications only.
* Refer to the owner's manual provided by your main speaker manufacturer to
determine your main speaker's low end frequency response.
N
OTES
WARNING: Severe damage may result from