Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ryobi RCS18X3050
Summary of Contents for Ryobi RCS18X3050
- Page 1 ORIGINAL INSTRUCTIONS Cordless Chainsaw RCS18X3050 OCS1830...
- Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modification.
-
Page 3: Intended Use
Safety, performance, and dependability have been given a power tool. Distractions can cause you to lose top priority in the design of your cordless chainsaw. control. ELECTRICAL SAFETY INTENDED USE ■ Power tool plugs must match the outlet. Never The cordless chainsaw is only intended for use outdoors. modify the plug in any way. -
Page 4: Chainsaw Safety Warnings
connected and properly used. Use of dust collection maintained. can reduce dust-related hazards. ADDITIONAL GENERAL SAFETY WARNINGS POWER TOOL USE AND CARE ■ Some regions have regulations that restrict the use of ■ Do not force the power tool. Use the correct power the product. - Page 5 on the rear handle and your left hand on the front saw. As a chainsaw user, you should take several steps to handle. Holding the chainsaw with a reversed hand keep your cutting jobs free from accident or injury. configuration increases the risk of personal injury and Kickback is the result of tool misuse and/or incorrect should never be done.
- Page 6 bar and could result in serious injury or fatality. The should comply with EN 397 and be CE marked – length of chain depends on the temperature. Check the Hearing protection tension frequently. – should comply with EN 352-1 and be CE marked ■...
-
Page 7: Residual Risks
Remove dirt, stones, loose bark, nails, staples and wire cut, wait for the saw chain to stop before you move the from the tree. chainsaw. Always stop the motor before moving from tree to tree. Do not attempt to fell trees which are rotten or have been damaged by wind, fire, lightning, etc. -
Page 8: Risk Reduction
■ Unforeseen, abrupt movement, or kickback of the guide guide bar and chain combinations recommended by the bar (cutting hazards) manufacturer. As saw chains are sharpened, they lose some of the low RISK REDUCTION kickback qualities and extra caution is required. For your safety, replace saw chains when cutting performance It has been reported that vibrations from hand-held tools decreases. -
Page 9: Operation
Recommended chain lubricating oil movement or falling to prevent injury to persons or damage to the product. ■ The manufacturer recommends you use only Ryobi chainsaw lubricating oil. (Available from your authorised TRANSPORTING LITHIUM BATTERIES Ryobi service centre) Transport the battery in accordance with local and national INSTALLING THE BATTERY PACK provisions and regulations. -
Page 10: Maintenance Schedule
MAINTENANCE SCHEDULE dull chain is replaced with a new one, available from your authorised Ryobi service centre. The part number Daily check is available in the product specification table in this Bar lubrication Before each use manual. -
Page 11: Symbols On The Product
SYMBOLS ON THE PRODUCT Set the chain brake to the RUN position. Safety alert Rotate to adjust chain tension + = Tighten the chain Read and understand all instructions - = Loosen the chain before operating the product, follow all warnings and safety instructions. - Page 12 RCS18X3050...
- Page 13 OCS1830...
- Page 15 4-5.5 mm...
- Page 17 p.17 p.18 p.19 p.20 p.21...
- Page 18 p.23 p.24 p.25 p.26...
- Page 19 5 cm / 2 in 5 cm / 2 in...
- Page 24 4-5.5 mm...
- Page 25 4-5.5 mm...
-
Page 29: Product Specifications
The declared vibration value has been measured with a Cordless Chainsaw standard test method and may be used to compare one tool with another. Model RCS18X3050/OCS1830 The declared vibration value may be used in a preliminary Rated voltage 18 Volts assessment of exposure. - Page 30 4. For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation.
- Page 31 AUTHORISED SERVICE CENTRES ACD PLANT LTD C J Sinclair Limited ToolTech Industrial Equipment 145 Southbank Road 44 Victoria Road 227 E Dunhill Road, Macosquin Coundon St Peters Coleraine, Co Londonderry Coventry, West Midlands Broadstairs, Kent BT514LQ CV6 1FG CT10 2UG Phone: 028 70359493 Phone: 02476 594348 Phone: 01843 869400...
-
Page 32: Declaration Of Conformity
Max-Eyth-Strasse 10, 71364 Winnenden, Germany Herewith we declare that the product Cordless Chainsaw Brand: RYOBI Model number: RCS18X3050/OCS1830 Serial number range: 46211501000001 - 46211501999999 is in conformity with the following European Directives and harmonised standards 2006/42/EC, 2014/30/EU, 2000/14/EC, 2005/88/EC, 2011/65/EU, EN 60745-1:2009+A11:2010,... - Page 36 Techtronic Industries GmbH Max-Eyth-Straße 10, 71364 Winnenden, Germany 960994069-02...