Iris; Main Operation; Battery/P2Card - Panasonic SPX900 Operating Instructions Manual

8-5-8

IRIS

Items/ Adjustable
Data Saved Range
A.IRIS LEVEL 000 Set the target value for auto iris.
:
050
:
– C U F E 100
A.IRIS PEAK/ 000 Determine the peak-to-standard ratio for the
auto iris.
AVE :
040
A larger value sets the auto iris to respond to
:
the peak in the IRIS detection window, while
100
a smaller value sets it to respond to the
average value in the window.
– C U F E
A.IRIS MODE NORM1 Select the auto iris detection window.
NORM1:The window closer to the center of
NORM2
CENTR
NORM2:The window closer to bottom of the
CENTR: The spot window in the center of the
– C U F E
S.IRIS LEVEL 000 Set the target value for the super iris.
:
080
:
– C U F E 100
IRIS GAIN CAM Select which unit controls IRIS GAIN.
<Note>
LENS
Lenses with an extender, such as
sold before FUJINON DIGI POWER,
perform IRIS compensation while enabling
the extender. Therefore, if this setting is
switched to CAM, the camera's iris control
will not operate properly.
– C U F E
IRIS GAIN 01 Set the adjustable value for IRIS GAIN. This
setting is effective when CAM is selected for
VALUE :
08
IRIS GAIN.
:
– C U F E 20
106
Remarks
the screen.
screen.
screen.
2,
8-6

MAIN OPERATION

8-6-1

BATTERY/P2CARD

Items/ Adjustable
Data Saved Range
BATTERY PRO14
SELECT TRIM14
HYTRN50
HYTRN100
HYTRN120
DIONIC90
DIONIC160
HP-90L
BP-H120
NP-L50
ENDURA50
ENDURA80
BP-L60/90
NiCd14
NiCd13
NiCd12
TYPE A
TYPE B
– C U F –
EXT DC IN AC_ADPT
SELECT PRO14
TRIM14
HYTRN50
HYTRN100
HYTRN120
0.8
DIONIC90
DIONIC160
HP-90L
BP-H120
NP-L50
ENDURA50
ENDURA80
BP-L60/90
NiCd14
NiCd13
NiCd12
TYPE A
TYPE B
– C U F –
BATT NEAR ON
END ALARM OFF
– C U F –
BATT NEAR ON
END CANCEL OFF
– C U F –
BATT END ON
ALARM OFF
– C U F –
BATT REMAIN 100%
FULL 70%
– C U F –
The ____ in the Adjustable Range column indicates the preset
mode.
Remarks
Select the battery to use. Remaining
capacity detection is also performed
according to the selected battery.
The selectable battery types change
depending on the settings under [8-6-2
BATTERY SETTING1] and [8-6-3 BATTERY
SETTING2].
Set the remaining capacity detection type
when a battery is connected to the DC IN
connector. Remaining capacity detection is
also performed according to the selected
battery type.
The selectable battery types change
depending on the settings under [8-6-2
BATTERY SETTING1] and [8-6-3 BATTERY
SETTING2].
<Note>
The % display is disabled even when a
digital battery is connected to the DC IN
connector.
Select whether or not to set the alarm to
beep for BATT NEAR END ALARM.
If set to ON, the warning tone and indication
can be canceled by pressing the MODE
CHECK button when BATT NEAR END
ALARM is triggered.
Select whether or not to set the alarm to
beep for BATT END ALARM.
Set the display content of the remaining
battery capacity indicator bars in the display
window when using a digital battery.
100%: Indicate FULL at 100% capacity.
70%: Indicate FULL at 70% capacity.