Related Manuals for Hyundai HY2192
Summary of Contents for Hyundai HY2192
- Page 1 20V Cordless Pole Saw HY2192 Instruction Manual WARNING: Read the instructions carefully before use.
-
Page 2: Table Of Contents
Contents Technical Data…………......29 Introduction……..……………………………3 Recycling And Disposal..………………...30 Safety Information…..…………………..4-13 Understand Your Machine.…..…………...4 Personal Safety...…….……………………4-5 Declaration Of Conformity…..…………..31 Inspect Your Machine…………………..5 Work Area…….……………………………..6 Useful Information…..……………………..32 During Use…….………………………………7 Our YouTube Channel…..………………..32 Batteries…….…………………………………8 Warranty…………………………………….32 Charger………………………………………..8 Manual Updates….……………………….32 Electricity…….………………...…………...8-9 Returning Your Product….……………….32 Double Insulated Devices…..……..9 Leaving A Review….……………………...32 Vibrations….…………………………..10 Ordering Spare Parts.……………………..32... -
Page 3: Introduction.........................................3 Technical Data
THE MACHINE. Keep for future reference and pass it on if the machine is loaned or sold to another user. This manual has been produced by Hyundai Power Products and should be kept with the product. Please read and understand these instructions before you use your product. -
Page 4: Safety Information............................4-13 Recycling And Disposal
Safety Information Understand Your Machine • WARNING! You must read these instructions carefully before operating the machine. Make sure that you are familiar with the controls and properly operate the machine. You must learn how to stop the machine quickly. If you do not follow the warnings and instructions, it may result in fire and/or serious injury. -
Page 5: Inspect Your Machine
Safety Information Personal Safety (Continued) • Do not touch parts that might be hot from operation. Allow parts to cool before attempting to maintain, adjust, or service. • Do not overreach. Keep proper footing and balance at all times. This enables better control of the machine in unexpected situations. -
Page 6: Work Area
Safety Information Work Area • You must only work in daylight or with good artificial light in good visibility conditions. Do not work at night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the area. -
Page 7: During Use
Safety Information During Use • Do not operate the machine in confined areas where there may be a risk of crushing the operator between the machine and another object. • Never attempt to make any adjustments, while the machine is running. •... -
Page 8: Charger
Safety Information Batteries Batteries present a risk if they become damaged by the possible leaking of electrolyte. Electrolyte is an acid and can cause serious burn injuries. Care should be taken when working on or near them. NOTE: the electrolyte may be in a liquid or gel form. -
Page 9: Electricity
Safety Information Electricity (Continued) • Power tools plug must match the outlet. Never modify the plug in any way. DO NOT use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. •... -
Page 10: Residual Risks
Safety Information Vibrations (Where Applicable) • Prolonged use of hand held (operated) machines will cause the user to feel the effects of/from vibrations. These vibrations can lead to white finger (Raynaud’s phenomenon) or carpal tunnel syndrome. This condition reduces the ability of the hand to feel and regulate temperature, causing numbness and heat sensations and may cause nerve damage and circulatory tissue death. -
Page 11: Intended Use
Safety Information Intended Use The HY2192 is a 20V Cordless Pole Saw. It is powered by a 775W HYUNDAI motor. This machine is specifically a pedestrian tool, manufactured according to the latest safety requirements. Every precaution is only effective when it’s followed exactly. -
Page 12: Personal Protective Equipment
Safety Information Personal Protective Equipment Appropriate Personal Protective Equipment (PPE), MUST be worn at all times when operating or repairing the machine. No protective equipment can ensure 100% protection. When selecting PPE, make sure it’s CE marked and it suits the user in terms of size, fit, etc. -
Page 13: Symbols On The Machine
Safety Information Symbols On The Machine We have provided safety messages in this manual and on the machine. This information alerts you to potential hazards that could hurt you or others. Please read these messages carefully. However, we may not have listed all of the possible hazards, you must also use your own judgement. - Page 14 2. Lay the contents out and check them. If any part is damaged or missing, you must not use the machine. Contact HYUNDAI POWER PRODUCTS immediately. 3. You must keep the packaging material in case the machine needs to be returned or repaired.
- Page 15 Unboxing *Not To Scale Features Blade Cover Power Safety Button Hedge Trimmer Head On/Off Trigger Oil Cap and Gauge Battery Level Indicator Head Angle Button Battery Release Button Trimmer Head Interlock 2.0Ah Lithium Ion Battery Battery Charger Pole Handle Interlock Telescopic Release Catch Shoulder Strap Strap Hoop...
-
Page 16: Assembly
Assembly HY2192 Main Body Assembly Insert the Pole Handle Interlock (F) into the Trimmer Head interlock (E). This is “keyed” so it will only fit 1 way, to avoid misconstruction. Rotate the Collar on the Pole Handle Interlock (F) clockwise to secure. -
Page 17: Pre-Operation Oil Top Up
Assembly Pre-Operation Oil Top up Ensure the Battery is Disconnected when filling with oil Remove the Oil Cap (C), and fill with the provided oil. To check a sufficient amount of oil, use the Oil Gauge to check Check the chain deflection, pinch the chain and lift. It should lift about 2-3mm. -
Page 18: Insert Battery
Assembly HY2192 Insert Battery Ensure battery is fully charged before assembly, see page Insert the Battery (N) into the Battery Carriage (I), with the Battery Release button (M) facing away from the carriage. An audible *click!* will be heard when it’s secured properly. -
Page 19: Operation
Operation Battery Charger Operation Ensure the power source switch is OFF when plugging in Battery Charger You MUST understand the whole Instruction Manual before any operation Slide the Battery (N) into the Battery Charger (O), by lining up the terminals on both. It will be secured with an affirmative *click!*. NOTE –... -
Page 20: Starting And Stopping
Operation HY2191 Starting and Stopping Warning! You MUST read and fully understand the whole user manual before operation *CAUTION* - The chain of this machine is sharp, and correct PPE must be worn with ALL machine operation. Remove the Blade Guard (A) To start the machine, you must firstly press the Power Safety Button (J). -
Page 21: Pole Extension
Operation HY2191 Starting and Stopping HY2192 Pole Extension Lift the latch on the Telescopic Release Catch (G). Extend the telescopic pole to your preferred length Press the Telescopic Release Catch (G) back into place, locking your selected length. www.hyundaipowerproducts.co.uk www.hyundaipowerproducts.co.uk... -
Page 22: Pivoting Head Operation
Operation Pivoting Head Operation CAUTION : Do not place hand between pivoting head and base. Failure to follow this caution could result in a pinch point injury. Place the machine on a sturdy flat surface. Push the Head Angle Button (D) either side of the machine and adjust Saw Head. -
Page 23: How To Cut Selected Branches
Operation How to cut selected branches Sawing of small branches Set your saw cut of smaller branches (0 0-8 cm) from top to bottom, as illustrated. Be aware of easily breaking of the branch if you have underestimated the size and weight. Be completely aware of the falling cut material. -
Page 24: Maintenance & Care
Maintenance & Care General Maintenance WARNING : Turn OFF the machine, allow all moving parts to come to a complete stop, and disconnect the power cord before maintaining the machine. You need to wear proper clothing and protective gloves whenever your hands are at risk. -
Page 25: Chain Maintenance
Maintenance & Care Chain Maintenance Sprocket Tip Lubrication CAUTION: The sprocket tip on your new saw has been pre-lubricated at the factory. Failure to lubricate the guide bar sprocket tip as explained below will result in poor performance and seizure, voiding the manufacturer’s warranty. Lubrication of the sprocket tip is recommended after 25 hours of use or once a week, whichever occurs first. - Page 26 Maintenance & Care Chain Maintenance Chain Sharpening WARNING: Always wear protective gloves during maintenance operations. Do not carry out maintenance when the machine is hot. For the inexperienced chain saw user, we recommend that the saw chain be professionally sharpened by the nearest professional service centre. If you feel comfortable sharpening your own saw chain, special tools are available from the professional service centre.
- Page 27 Maintenance & Care Chain Maintenance Chain Sharpening Sharpen the chain using protective gloves and a round file of ø5/32” (4mm). Always sharpen the cutters only with outward strokes observing the values in the diagram. After sharpening, the cutting links must all have the same width and length.
-
Page 28: Guide Bar Maintenance
Maintenance & Care Guide Bar Maintenance Guide Bar WARNING: Proper adjustment of the depth gauge is as important as proper sharpening of the chain. The bar should be reversed every 8 working hours to ensure uniform wear. Keep the bar groove and lubrication hole clean using a bar groove cleaner (optional). Check the bar rails frequently for wear. - Page 29 Technical Data Machine Specification Model HY2192 Telescopic Tube Total Length 2.4M Net Weight 3.09kg Voltage 20V MAX Chain Speed 4.5m/s www.hyundaipowerproducts.co.uk...
- Page 30 Recycling & Disposal Recycling & Disposal We do not offer a takeback scheme for the recovery of Waste Electrical Electronic Equipment (WEEE) & Batteries. Instead the responsibility to dispose of WEEE and/or Batteries is passed onto you by us. So when it becomes necessary to dispose of your machine you must take it to your local Civic Amenity Site.
-
Page 31: Declaration Of Conformity
Genpower Ltd Isaac Way, Pembroke Dock, SA72 4RW Country of Origin: China Description: Cordless Pole Saw SKU Code: HY2192 Date of Issue: 21/12/2021 Regulations and Directives of Compliance • 2006/42/EC The Machine Directive • 2014/30/EU EMC Directive • 2011/65/EU RoHS... -
Page 32: Useful Information
Go to YouTube and search ‘Hyundai Power Products’. Warranty Proof of purchase will be required before you make a warranty claim. Full warranty terms and conditions can be found on the HYUNDAI POWER PRODUCTS website: www.hyundaipowerproducts.co.uk Manual Updates Our manuals are constantly being reviewed and updated. Should you find an error, omission or something unclear, please contact us for assistance. -
Page 33: Product Record
Product Record Information As soon as you have purchased the machine, we recommend that you fill out the following. If you need to contact an authorised dealer or customer service for information on servicing, you may need to provide the following information. Date Of Purchase:……………………………………………………………………………….. -
Page 34: Notes
Notes www.hyundaipowerproducts.co.uk... - Page 35 Our friendly aftersales team will be more than happy to help you. Phone Call our team on 01646 687 880 Email aftersales@hyundaipowerproducts.co.uk Online Live Chat Go to www.hyundaipowerproducts.co.uk Post Genpower Ltd, Isaac Way, Pembroke Dock, Pembrokeshire, SA72 4RW. Hyundai Support Website Go to hyundaisupport.co.uk www.hyundaipowerproducts.co.uk...
- Page 36 Importer: GENPOWER LTD Isaac Way, London Road, Pembroke Dock, UK, SA72 4RW. T: +44 (0) 1646 687 880 E: info@hyundaipowerproducts.co.uk www.hyundaipowerproducts.co.uk Imported / Distributed by Genpower Ltd for the United Kingdom & Ireland Licensed by Hyundai Corporation, Korea...