POLE SAW / HEDGE TRIMMER Hedge Trimmer 17. Handle Introduction 18. Lock/release 19. Gear housing The operating instructions are a part of this product. They contain 20. Cutter bar 21. Base plate (hedge trimmer) important information about safety, usage and disposal. Before using the 22.
Noise and vibration information: NOTE Noise measurement value determined in accordance with ISO 22868, ► The vibration level specified in these instructions has been measured EN 10517. The A-rated noise level of the power tool is typically as follows: in accordance with the standardised measuring procedure specified Hedge Trimmer: in EN ISO 11 806-1, EN ISO 10517, EN ISO 11680-1 and can be Sound pressure level L...
Page 8
Attention! Risk of suffocation! Press the fuel pump (primer) 6x Caution! Poisonous CO vapours (carbon monoxide vapours)! Mixing ratio: 40 parts petrol to 1 part oil Do not use the appliance in confined spaces! Warning! Do not use circular saw blades for the cutting Semi-synthetic 2-stroke oil and unleaded petrol at 40:1 ratio blade function .
Hedge Trimmer Safety – Do not smoke . – Refuel outside only . – Never store the hedge trimmer or the fuel tank in a room where there is IMPOrTAnT! reAD CAreFUllY BeFOre USe! an open flame, for example in a hot water boiler . KeeP FOr YOUr reCOrDS .
Maintenance and storage ■ Carry the hedge trimmer by the front handle when switched off, with the cutter bar facing away from your body. When transporting a) If the hedge trimmer is shut down for maintenance, inspection or storage, or storing the trimmer, always put on the protective cover. Careful switch off the engine, pull the spark plug connector off the spark plug handling of the appliance reduces the likelihood of accidental contact and ensure that all rotating parts have come to a standstill .
Use and handling ■ Any such reaction can lead to you losing control over the saw and possibly injuring yourself . Do not rely solely on the chainsaw's built-in ■ Never start the appliance before the blade, saw chain and sprocket safety devices .
Personal safety Operational safety instructions for cutting blades ■ The appliance can blind and cause injuries to bystanders . Maintain a Preparation minimum distance of 15 metres in all directions between the appliance and other people or animals . ■ The cutting blade flings objects and soil with great force .
Before use Assembling the hedge trimmer ♦ Start by undoing the screw grip on the boom of the engine unit. &CAUTION! ♦ ' Push the pin on the front boom� of the ■ Always wear non-slip footwear and appropriate safety clothing hedge trimmer into the groove on the engine such as protective gloves, a hard hat, a protective mask and safety goggles as well as hearing protection.
Tightening and checking the saw chain & WARNING! ► Wear protective gloves! There is a danger of injury from the sharp cutting teeth! ♦ Turn the chain-tensioner screw l4l) in a clockwise direction using the flat-blade screwdriver (i to increase the tension. ♦...
ATTENTION! Left-hand thread! Putting on the carrying harness & CAUTION! ■ Please pay attention to the statutory provisions in the relevant noise protection regulations. ■ The following adjustments can be made to make sure that you can work without becoming fatigued. The settings may vary depending on Before starting the appliance, always check that: your body size.
Turning the engine off Prevent kickback emergency stop sequence When working with the 3-section cutting blade there is a risk of kickback if If the appliance needs to be stopped immediately, turn the On/Off switch the blade strikes against solid obstacles (tree trunks, branches, tree stumps, rocks or similar) .
Cleaning Saw in sections Trim long or thick branches before you make the final cut (see figure) . Cleaning the engine unit NOTE ■ Clean the appliance thoroughly after every use . ■ Always switch off the appliance before cleaning and then disconnect the spark plug connector ■...
Maintenance Storage and transportation Air filter maintenance Contaminated air filters reduce the engine performance due to low air ■ Store the appliance in a safe location. supply to the carburettor. ■ Store the appliance and accessories in a safe location which is pro...
Troubleshooting Maintenance intervals engine unit Pole pruner The figures given here are based on normal operating conditions . In the Problem Possible cause Troubleshooting event of more difficult conditions, such as strong dust generation and The engine does Incorrect start-up process . Follow the instructions longer daily operating hours, the given intervals are to be reduced corres- not start .
Warranty Proof of purchase will be required before you make a warranty claim. Full warranty terms and conditions can be found on the HYUNDAI POWER PRODUCTS website: www.hyundaipowerproducts.co.uk...
Contact Us Phone Call our team on 01646 687880, open Monday-Friday 8.30am-5pm. Email aftersales@hyundaipowerproducts.co.uk Online Live Chat Go to www.hyundaipowerproducts.co.uk Live chat is open Monday-Friday from 8.30am-5pm.
Notified Body for EC Directive 2000/14/EC TÜV Rheinland (Shanghai) Co., Ltd. Product Details Brand: Hyundai Model: HYMT5200X, HYBC5200X, HYPS5200X, HYPT5200X Description: Petrol brushcutter, multi-tool, pole saw and pole hedgetrimmer. Name and address of technical documentation holder and EU distributor: Genpower Ltd, Isaac Way, Pembroke Dock, Pembrokeshire, SA72 4RW, UK.
Page 23
Isaac Way, London Road, Pembroke Dock, UNITED KINGDOM, SA72 4RW T: +44 (0) 1646 687 880 F: +44 (0) 1646 686 198 E: info@hyundaipowerequipment.co.uk www.hyundaipowerproducts.co.uk Imported/Distributed by Genpower Ltd for The United Kingdom & Ireland Licensed by Hyundai Corporation, Korea...