Sony HCD-GTK1i Service Manual page 15

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : parts extracted from the conductor side.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.
• Abbreviation
AR : Argentina model
AUS : Australian model
CND : Canadian model
E2 : 120V AC area in E model
E4 : African model
E51 : Chilean and Peruvian model
MX : Mexican model
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HCD-GTK1i/GTK2i
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.
• 2 : nonfl ammable resistor.
• C : panel designation.
Note: Note:
The components identi- Les composants identifi és
fi ed by mark 0 or dotted par une marque 0 sont
line with mark 0 are criti- critiques pour la sécurité.
cal for safety. Ne les remplacer que par
Replace only with part une piéce portant le nu-
number specifi ed. méro spécifi é.
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
* : Impossible to measure
• Voltages are taken with VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : AUDIO
I : IPOD
: TUNER
f
: USB
J
• Abbreviation
AR : Argentina model
AUS : Australian model
CND : Canadian model
E2 : 120V AC area in E model
E4 : African model
E51 : Chilean and Peruvian model
MX : Mexican model
• Waveforms
– MAIN Board –
1 IC102 qh (CLK IN)
556.7 mVp-p
50 Hz
200mV/DIV, 24.6msec/DIV
2 IC100 qd (/X-OUT)
266.7 mp-p
376mHz
100mV/DIV, 12.3msec/DIV
15 15
HCD-GTK1i/GTK2i
– IPOD Board –
3 IC1100 ra (X OUT-PLL)
320.0mVp-p
30 MHz
100mV/DIV, 49.3nsec/DIV